ADVANCED OPERATIONS: USING CUE POINTS/LOOP POINTS MEMORY
7Storing CUE points
Insert a Multimedia Card in the card insertion slot and perform the same pro- cedure as when the internal memory is used. ☞ P.16
7Storing Loop points
Insert a Multimedia Card in the card insertion slot and perform the same pro- cedure as when the internal memory is used. ☞ P.16
7Calling stored Cue/Loop points
Insert a Multimedia Card in the card insertion slot and perform the same pro- cedure as when the internal memory is used. ☞ P.16
7Deleting stored Cue/Loop points
Insert a Multimedia Card in the card insertion slot and perform the same pro- cedure as when the internal memory is used. ☞ P.16
7Deleting data from a specific disc
Deleting data from the memory card of a specific disc.
1.Insert the disc.
¶Insert the disc from which to delete Cue/Loop points etc. from the memory card.
2.Insert the Multimedia Card (MMC) in the card insertion slot.
¶When Cue and Loop points are stored, the calendar display and the play- back address display lights in red.
3.Hold down the CUE/LOOP DELETE button for 5 seconds or longer.
¶[DISC DELETE? PUSH MEMORY] is displayed on the display.
4.Press the CUE/LOOP MEMORY button.
¶With [DELETE] shown on the display, that disc’s Cue/Loop points etc will be deleted from the memory card.
¶All the lights of the calendar display and the Cue/Loop display etc. of the playback positioning display will go out.
7Formatting cards
Formatting deletes all data on the MMC.
1.Removing the disc.
2.Insert the Multimedia Card (MMC) in the card insertion slot.
3.Hold down the CUE/LOOP DELETE button for 5 seconds or longer.
¶[FORMAT? PUSH MEMORY] is displayed.
4.Press the CUE/LOOP MEMORY button.
¶[FORMAT] is displayed and all data on the card is deleted.
7Data other than CUE/LOOP stored on MMC
¶ Hot cue points A, B, C
Hot cue points A, B and C are automatically stored on MMC. When a disc storing hot cue points is inserted, the [A], [B] and [C] indicators light in green. To call stored hot cue points, press the A, B or C button.
The green flashing indicator will light steadily (when the call is made, sound will be interrupted briefly). If call is not needed, press the HOT CUE REC MODE button. The indicator will change to red, and you can set the hot cue point. To call the hot cue point, remove and replace the disc or MMC and the A, B and C buttons will blink on and off, at this time it is possible to call.
¶ WAVE display
When a wave display for one track is completed it is automatically stored on the MMC. When the same track is played again, the stored WAVE display is automati- cally called. Data for items beyond track number 21 are stored on the MMC.
CUE/LOOP
MEMORY
CUE/LOOP
DELETE
CUE/LOOP
CALL 2, 3
Copying MMC Data (From One MMC to Another)
Use the following procedure to copy data on one MMC (CARD A) to another MMC (CARD B).
1.Remove the disc.
2.Remove the card.
3.Hold down the CUE/LOOP MEMORY button for 5 seconds or longer.
¶[MMC>MMC(OVERWRITE), CARD A IN] is displayed.
4.Insert the MMC to copy data from in the card insertion slot.
¶[READING] is displayed.
5.After a few minutes, [CARD B IN] is displayed. Remove card A and insert the destination card (CARD B) in the insertion slot.
¶[WRITING] is displayed.
6.After a few minutes [CARD A IN] is displayed.
7.Repeat steps 4 to 6 twice for a 8M card and four times for a 16M card to complete the copy operation.
¶[COMPLETE] is displayed when copying is completed.
It is impossible to copy from a card with greater capacity to the receiving card.
Copying Data in the Internal Memory (Copying from internal memory onto MMC)
This procedure copies data in internal memory to MMC.
1.Remove the disc.
2.Remove the card.
3.Hold down the CUE/LOOP MEMORY button for 5 seconds or longer.
¶[MMC>MMC(OVERWRITE), CARD A IN] is displayed.
4.Press the CUE/LOOP MEMORY button again.
¶[INT>MMC(OVERWRITE), CARD IN] is displayed.
5.Insert the destination MMC.
¶[WRITING] is displayed.
¶[COMPLETE] is displayed when copying is completed.
*If the [Err] message appears in one of the displays, the memory data has not been copied properly. Turn the power to both players OFF and then ON again, and repeat the copying proce- dure from step 1.
*When copying from MMC to MMC, or from internal memory to MMC, the MMC memory is overwritten; as a result, any data previously recorded in MMC will be completely erased.
*Perform this procedure with the DIGITAL OUT mode set to "DJ".
17
<DRB1339>
En