Getting started
02
Using the Auto MCACC setup for optimal surround sound
The Multichannel Acoustic Calibration (MCACC) system measures the acoustic characteristics of your listening area, taking into account ambient noise and testing for channel delay and channel level. After you have set up the microphone provided with your system, the receiver uses the information from a series of test tones to optimize the speaker settings and equalization (Acoustic Calibration EQ) for your particular room.1
Important
•These test tones are loud; however, do not turn the volume down during setup as this may result in a
•Make sure the mic and speakers are not moved during the MCACC setup.
2Place the microphone at your normal listening position.
Place it about ear height, and make sure it is level by using a table or chair.
Make sure there are no obstacles between the speakers and the microphone.
3 If the system is off, press
STANDBY/ON to turn the power on. If the tuner is selected, switch the input source.
4 Press SHIFT+MCACC.
Try to be as quiet as possible after pressing SHIFT+MCACC. The volume increases automatically and the system outputs a series of test tones.
• Press SHIFT+MCACC to cancel and revert |
to the previous Auto MCACC settings. |
• If the noise level is too high, NOISY blinks |
in the display for five seconds. To exit and |
English Deutsch Français Italiano
STANDBY |
| TUNER | SOUND |
/ON | DVD CD | (FM/AM) | RETRIEVER |
| USB | LINE | OPEN/CLOSE |
|
| ||
|
|
| PLAYLIST |
1 | 2 | 3 | 1 |
| AUDIO | SUBTITLE |
|
4 | 5 | 6 | 2 |
| ANGLE | ZOOM |
|
7 | 8 | 9 | 3 |
CLEAR | DISPLAY |
|
|
|
|
| 0 |
| TV CONTROL |
| SLEEP |
|
|
|
| ||
TOPMENU | TUNE | MENU |
|
|
|
|
|
| INPUT CHANNEL | VOLUME | MUTE |
SETUP |
| SR |
|
|
|
ST | ENTER | ST | SHIFT | VOLUME |
|
HOME |
|
|
|
|
|
MENU |
| RETURN |
|
|
|
MCACC | TUNE | TESTTONE |
|
|
|
F.S.SURR | SURROUND ADVANCED | SOUND |
|
|
|
check the noise levels2, press |
SHIFT+MCACC, or to try again, press |
ENTER when RETRY shows in the display. |
• If you see an ERR MIC or ERR SP message |
in the display, there may be a problem with |
your mic or the speaker connections. To try |
again, press ENTER when you see RETRY.3 |
Nederlands
1Connect the microphone to the MCACC MIC jack on the rear panel.
|
|
| COMPONENT | PR |
|
|
| VIDEO |
|
|
|
| VIDEO | PB |
|
|
|
| |
OPTICAL |
| IN |
| Y |
LINE 1 |
|
|
| |
DIGITAL IN | MCACC |
|
|
|
SETUP MIC | CONTROL | VIDEO OUT |
| |
|
|
When the MCACC setup is complete, the volume level returns to normal and COMPLETE4 shows in the display, indicating that the MCACC setup is complete and Acoustic Calibration EQ has been activated.5
Español
Note
1You only need to use the Auto MCACC setup once (unless you change the placement of your speakers or your room layout).
2 • If the room environment is not optimal for the Auto MCACC setup (too much ambient noise, echo off the walls, obstacles blocking the speakers from the microphone) the final settings may be incorrect. Check for household appliances (air conditioner, fridge, fan, etc.), that may be affecting the environment and switch them off if necessary.
•Some older TVs may interfere with the operation of the mic. If this seems to be happening, switch off the TV during the Auto MCACC setup.
3 If this doesn’t work, press SHIFT+MCACC, turn off the power, and check the problem indicated by the error message, then try the Auto MCACC setup again.
4 If COMPLETE doesn’t appear, it is likely an error occurred during the setup. Please check all connections and try again. 5 See Listening with Acoustic Calibration EQ on page 17 to switch on/off Acoustic Calibration EQ.
11
En