Pioneer HTP-LX70, SSP-LX70ST, SX-LX70W, AS-LX70 manual Getting started Chapter

Page 23

Getting started

Chapter 4

Getting started

Important

•RCV Press to set the remote control to receiver control mode in order to operate the receiver subwoofer (make sure that the LCD displays the RECEIVER screen, as shown below).

04

1Connect the microphone to the MCACC SETUP MIC jack on back of the display unit.

2Place the microphone at your normal listening position.

Place it about ear height, and make sure it is level by using a table or chair.

RECEIVER

SURR

ADV

F.S.

SURR

SURR

Using the Auto MCACC setup for optimal surround sound

The Multichannel Acoustic Calibration (MCACC) system measures the acoustic characteristics of your listening area, taking into account ambient noise, and testing for channel delay and channel level. After you have set up the microphone provided, the system uses the information from a series of test tones to measure standing wave and reverb, optimizing the speaker settings and equalization (MCACC Effect) for your

particular room.1

Important

•The test tones used for Auto MCACC setup are loud; however, do not turn the volume down during setup as this may result in a sub-optimal setup.

•Make sure the microphone and speakers are not moved during the MCACC setup.

Make sure there are no obstacles between the speakers and the microphone.

RECEIVER

3 If the receiver subwoofer is off, press RECEIVER to turn the power on.

4MCACC Press MCACC.

Try to be as quiet as possible after pressing MCACC. The volume increases automatically and the system outputs a series of test tones.

•To cancel Auto MCACC setup before it has finished, press MCACC. The unit will continue to use the previous settings.

•If the ambient noise level is too high, Noisy! blinks in the display for five seconds. To exit and check the noise levels2, press MCACC, or to try again, press ENTER when Retry shows in the display.

•If you see an Error MIC! or Error Speaker! message in the display, there may be a problem with your mic or the speaker connections. To try again, press ENTER3.

When the MCACC setup is complete, the volume level returns to normal, Complete4 shows in the display, and MCACC Effect is activated.5

•Be sure to disconnect the microphone from this unit upon completion of the Auto MCACC setup.

Note

1 You only need to use the Auto MCACC setup once (unless you change the placement of your speakers or your room layout).

2• If the room environment is not optimal for the Auto MCACC setup (too much ambient noise, echo off the walls, obstacles blocking the speak- ers from the microphone) the final settings may be incorrect. Check for household appliances (air conditioner, fridge, fan, etc.), that may be affecting the environment and switch them off if necessary.

• Some older TVs may interfere with the operation of the mic. If this seems to be happening, switch off the TV during Auto MCACC setup.

3If this doesn’t work, press MCACC, turn off the power, and check the problem indicated by the Error message, then try the Auto MCACC setup again.

4If Complete doesn’t appear, it is likely an error occurred during the setup. Please check all connections and try again.

5See Listening with MCACC Effect on page 27 to switch on/off MCACC Effect.

23

En

Page 22 Page 24
Image 23
Page 22 Page 24
Contents HTP-LX Operating Environment Thank you for buying this Pioneer productVentilation Caution Contents Receiver subwoofer SX-LX70W box Accessory box AS-LX70What’s in the box Additional informationHome theater sound setup Speaker Setup GuideSpeaker Setup Guide Chapter Safety precautions when setting upNon-skid pads x Speaker Setup GuideAdditional notes on speaker placement Connect the speaker systemSide panel Connecting upConnecting up Chapter Receiver subwooferRear panel Connecting upBack of display unit FM antenna Connecting up Basic connectionsReceiver subwoofer Display unit Display cable AM loop antennaConnect each speaker Black Red + Color-coded wireAssemble the AM loop antenna Connect the AM and FM antennas1To Hdmi input Receiver subwooferDisplay unit Controls and displaysControls and displays Chapter Display Controls and displaysOperating the receiver subwoofer Controls and displays Remote controlLCD touch screen Operating the built-in FM/AM tunerCH Enter Operating Pioneer plasma televisions and TVsHome Menu CH RTNHome Menu Disp Play ModeTOP Menu / Disc Navigator MenuSubtitle Disp TOP MenuAudio Zoom CM Skip commercial skip HDDDVD CM Back commercial backStop REC Putting the batteries in the remote controlJukebox RECChoosing and operating a source component Controls and displays Using the remote controlOperating the remote control Using the LCD touch screenGetting started Chapter Using the Auto Mcacc setup for optimal surround soundGetting started Effective Sound for optimum sound Auto listening modeListening to your system Listening to your system ChapterListening to your system Using Advanced SurroundCenter image setting Dolby Pro Logic II Music settingsListening in stereo Using Front Stage Surround AdvanceGenre Sync Mode Using the Sound RetrieverListening to your system Listening with Mcacc Effect Listening to the radio Listening to the radioListening to the radio Chapter Changing the frequency step Listening to station presetsMemorizing stations Speaker distance setting1 Surround sound settingsSurround sound settings Chapter Using the Sound Setup menuDynamic Range Control Surround sound settingsDual mono setting LFE Attenuate Adjusting the channel levels using the test toneUsing the Virtual Surround Back mode Other connections Connecting auxiliary componentsConnecting for digital audio Connecting an analog audio componentListening to an external audio source Connecting an iPodOther connections Connecting using Hdmi Other connections Connecting external antennasReceiver screen Hdmi mode settingControl mode in order to operate the receiver About HdmiHdmi Control-compatible Pioneer plasma television Making the Hdmi Control connectionsHdmi Control Setting the Hdmi optionsSetting the Hdmi Control mode Synchronized amp mode Before using synchronizationAdditional information Chapter Setting up the remote to control your TVSetting the sleep timer Additional informationManufacturer Codes Additional information TV Preset code listSurround sound formats Additional information Resetting the systemInstallation and maintenance Hints on installationAdditional information General Additional information TroubleshootingThrough Mode Tuner Antenna refer to Connecting external antennas onHdmi C.ERR Displayed MessagesSacd DTS-HD Hdmi C.ERR 2CSSP-LX70ST Satellite Speaker Additional information SpecificationsAccessories Accessory box AS-LX70 D3-4-2-1-7cAChH Page 使用測試音調整聲道位準 使用 「自動 MCACC」設定以達最佳環繞音效清潔布 Hdmi Control請確認包裝箱內有下列項目的物品。 遙控器 （第 15 頁）準備揚聲器 01 揚聲器設定指南設定時應注意的安全措施 家庭劇院音效設定不使用隨附的揚聲器支座時 揚聲器設定指南揚聲器系統接線 關於揚聲器擺設的其他注意事項側面板 02 接線 接收重低音揚聲器後面板 顯示裝置背面前置／ 中置揚聲器 （左側） 環繞聲 （右側） 02 接線 基本連接顯示裝置 接收重低音揚聲器 顯示連接線 AM迴路天線顏色代碼的接頭 （連接至接收重低音揚聲器） 連接顯示裝置與接收重低音揚聲器。組裝 AM 迴路天線。 連接所有揚聲器。將重低音揚聲器連接至電視機。 02 接線接收重低音揚聲器 關於連接數位來源設備的方式，請參閱第 33 頁。前面板顯示 控制與顯示顯示裝置 頂部按鈕（第 24 頁）。 03 控制與顯示顯示幕 選擇直接聲音時 （即關閉有效聲音時）指示燈會亮起如需使用遙控器的詳細資訊，請參閱第 22 頁上的操 遙控器操作接收重低音揚聲器 用於選擇預設電台。 按下可清除任何輸入的內容並重新輸入。用於搜尋電台頻率。 按下可進入音效選單，進而調整低音與高音等。操作先鋒電漿電視和一般電視機 13 數字按鍵 Home Menu Zoom12 數字按鍵 Return ZoomAudio CM Skip （略過廣告） CM Back （返回廣告）17 錄製控制按鍵 裝入遙控器電池13 數字按鍵 使用液晶觸控畫面 03 控制與顯示 使用遙控器操作遙控器 若接收重低音揚聲器關閉，按下 Receiver 將其電源開啟。 開始操作使用 「自動 MCACC」設定以達最佳環 繞音效 請將麥克風置於正常的聆聽位置。以環繞音效聆聽 05 聆聽您的系統輸出的音效有效聲音 （適用於最佳聲音） 自動聆聽模式調整設定值，然後按下 Enter 確認。 聆聽您的系統輸出的音效使用 「先進環繞聲」功能 Dolby Pro Logic II Music 設定值以立體聲聆聽 使用前場前環繞聲模式類型同步化模式 使用 「聲音修正器」功能調整聲音延遲 聆聽您的系統輸出的音效 Mcacc 效果聆聽 調整低音及高音使用 「午夜」、「響度」及 「寂靜」聆 聽模式 改善 AM 音效不佳 06 收聽廣播收聽廣播 改善 FM 接收不良改變頻率間隔 記憶電台收聽預設電台 按鍵調整距離。 按鍵選擇聲道，或使用 鍵調整該聲道的位準。Enter 在完成時按下。 按鍵選擇揚聲器，或使用C. Mid －中等設定 開啟 「Sound Setup」選單。選擇設定。 C. High 或 D.R.C. Mid 用於 Dolby TrueHD 以外 的訊號。LFE 衰減 使用虛擬後環繞模式連接類比音效設備 其他接線連接輔助設備 數位音訊的連接連接 iPod 08 其他接線聆聽外接音訊來源 Control OUT 插孔。 其他接線 連接外接天線關於控制輸出連接 使用 Hdmi 連接出插孔。 Hdmi 模式設定關於 Hdmi 使用 Hdmi 連接線，將本接收重低音揚聲器的與HDMI Control相容的 Hdmi Control進行 Hdmi Control 連接 與HDMI Control 相容的若要使本功能發揮最大效用，建議您不要將 Hdmi 設 備連接至電漿電視，而是直接連接至本機的 Hdmi 端子。 設定 Hdmi 選項設定 Hdmi Control 模式 將電漿電視直接連接至本機。中斷與其他擴大器或 影音轉換器 （例如 Hdmi 開關）的直接連接可能導 致操作上的錯誤。同步化擴大器模式 使用同步化之前設定遙控器以控制電視機 10 其他資訊 10 章調暗顯示幕亮度 設定睡眠定時器請注意，指定正確預設代碼後，可能只有特定功能可供控制，或者表中的製造商代碼無法用於您目前的機種。 其他資訊 電視機預設代碼表Dolby Pro Logic II 和 Dolby Surround 10 其他資訊 重設系統 環繞音效格式安裝與維護 安裝提示中錄製的主要音源，不但未損失任何資料且保留了音 其他資訊10 其他資訊 故障排除 調諧器 Unknow 10 其他資訊顯示的訊息 DTS Express Dolby TrueHD Dolby D+ No MICSSP-LX70ST 衛星揚聲器 Pioneer Corporation

HTP-LX70, AS-LX70, SX-LX70W, SSP-LX70ST specifications

The Pioneer HTP-LX70, SX-LX70W, SSP-LX70ST, and AS-LX70 represent a culmination of advanced audio technologies designed to deliver a premium home theater experience. Each component showcases an array of features that cater to audiophiles and casual listeners alike, ensuring versatility and high-quality sound.

The HTP-LX70 is an outstanding home theater package that includes a powerful AV receiver and a complete set of speakers. It supports the latest audio formats, including Dolby Atmos and DTS:X, creating an immersive surround sound environment. The receiver is equipped with Pioneer’s MCACC (Multi-Channel Acoustic Calibration System), which automatically adjusts the speaker settings to optimize sound quality based on the unique characteristics of the room.

The SX-LX70W is a powerful stereo amplifier designed for high-fidelity audio reproduction. It delivers a robust output with low distortion, ensuring clear sound across various frequency ranges. The amplifier features a sleek design, combining aesthetics with functionality. It supports multiple connectivity options, including Bluetooth and Wi-Fi, allowing users to stream their favorite music effortlessly from various devices.

Complementing the system is the SSP-LX70ST, a sophisticated processor-preamp that handles the decoding of high-resolution audio formats. It features advanced digital signal processing capabilities, making it suitable for both music and cinema applications. The SSP-LX70ST provides numerous audio and video inputs, accommodating various sources, from gaming consoles to Blu-ray players. Its user-friendly interface allows for easy navigation and adjustments.

Finally, the AS-LX70 is a compact yet powerful active subwoofer that enhances the low-frequency response of any audio setup. With its adjustable crossover and phase control, the subwoofer integrates seamlessly with the other speakers, delivering deep, rich bass that enhances the overall listening experience. Its sleek cabinet design reduces resonance and optimizes sound performance.

In conclusion, the Pioneer HTP-LX70, SX-LX70W, SSP-LX70ST, and AS-LX70 together form an exceptional home entertainment solution, incorporating cutting-edge technologies and thoughtful design to ensure audio fidelity and versatility. Whether for movie nights or music sessions, this lineup offers an unparalleled listening experience, highlighting Pioneer’s commitment to quality and innovation. Whether you are an audiophile seeking the best sound reproduction, or simply looking to enhance your home theater setup, these products are crafted to meet the diverse needs of today’s consumers, creating the perfect audio environment for any occasion.
Top Page Image Contents