A t u r e s O v e r v i e w | Fender Music Pedal guide

F e a t u r e s • O v e r v i e w

The Fender® Cyber Foot Controller™ can be used to send Program Change and Continuous Controller messages to any MIDI device, hands-free. Especially designed to complement Fender Cyber-Series™amplifiers, the Cyber Foot Controller adds functionality to any amp that interprets the following messages of the MIDI specification, (features as they relate to Cyber- Series amps shown in brackets):

◊Program Change messages: Use the DOWN and UP buttons to index by “tens,” then a 0–9 button to select the “ones” digit. [Selects any preset using the MIDI map.]

◊Continuous Controller messages: Use the CONTINUOUS CONTROLLER pedal to send Control Change messages. [Adjusts a preset parameter defined by your amplifier.]

◊Volume control messages: Use the VOLUME pedal to adjust the volume on your amplifier. [Adjusts master volume.]

Cyber-Series™messages (unspecified MIDI messages that may be interpreted differently by other amps.)

◊TAP TEMPO/TUNER BUTTON

•Set the time/rate parameter for the current effect

•Activate the on-board tuner.

◊EFFECTS ON BUTTON

•Engage or bypass the current preset’s effect.

Thank you for choosing Fender®,

—Tone, Tradition and Innovation—since 1946.

C y b e r – S e r i e s M I D I F u n c t i o n s

A.TAP TEMPO / TUNER BUTTON

Sets the time/rate parameter for the active effect with one or more quick presses. A single press will set the parameter to its maximum value.

Activates the TUNER Mode when held down for 2 seconds, (“tun” is displayed). Press any button to exit TUNER Mode.

Sends a Program Change message to Bank 1, Program 127.1

B.EFFECTS ON (OFF) BUTTON

Alternately engages and bypasses the effects for the current preset.

Continuous Controller assignment: 85. Sends alternating Control Change messages: Data 0 for OFF; Data 127 for ON.

C.LED DISPLAY

•Displays the last Program Change number transmitted (flashes “ 00_ ” until the first number is selected).

•Displays “tun” in TUNER Mode.

•Displays MIDI Transmit Channel during selection.

MIDI TRANSMIT CHANNEL SELECTION

Transmit channel is set to 1 by default at power-up. To select channels (1–16): While holding down TAP TEMPO/TUNER {A}, press EFFECTS ON {B}, then

D. DOWN (–10) & UP (+10) BUTTONS Pre-selectsthe “tens” range for a Program Change number at these intervals:

0 0 0 ↔ 0 1 0 ↔ 0 2 0 ↔ 0 3 0 ↔ 0 40↔050↔060↔0 70↔ 0 8 0 ↔ 0 9 0 ↔ 1 0 0 ↔ 1 1 0 ↔ 120↔000↔(loop)...

A Program Change number is not transmitted until the “ones” digit is selected (see item {E} below). Note: The display stops flashing when a DOWN or UP selection returns you to the interval containing the last Program Change number transmitted.

E.0, 1, 2, 3, 4, 5, 6, 7, 8, 9 BUTTONS

Selects the “ones” digit of the Program Change number within the pre–selected“tens” range, and transmits the Program Change number. For example, if the display shows, “12_,” pressing the “7” button will cause “127,” to display and the Program Change 127 to transmit.

Note: “128” and “129” cannot be selected.

F.CONTINUOUS CONTROLLER PEDAL

Controls any programmable parameter for the current preset.

Continuous Controller assignment: 11. Sends Control Change messages 0–127.

G.VOLUME PEDAL

Controls the MASTER volume level. Continuous Controller assignment: 7. Sends Control Change messages 0–127.

release both buttons. Select a channel using the DOWN and UP buttons {D}, (channel selection is displayed). Press any “0–9” button to exit.

1Bank Change #1 is used only to access the TUNER Mode, all other messages are prefaced with Bank Change #0, which corresponds to the MIDI Map on Fender® Cyber-Series™ amplifiers.