Pioneer Important Information on HDMI and Speaker Settings for VSX-818V & VSX-918V
Page 70

12Additional information

Important information regarding the HDMI connection

(VSX-918V model only)

There are cases where you may not be able to route HDMI signals through this receiver (this depends on the HDMI equipped component you are connecting-check with the manufacturer for HDMI compatibility information).

If you aren’t receiving HDMI signals properly through this receiver (from your component), please try the following configuration when connecting up.

Configuration1

Connect your HDMI-equipped component directly to the display using an HDMI cable. Then use the most convenient connection (digital is recommended) for sending audio to the receiver. See the operating instructions for more on audio connections. Set the display volume to minimum when using this configuration.

Resetting the main unit

Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.

1Switch the receiver into standby.

2While holding down the ADVANCED SURROUND button, press and hold the STANDBY/ON button for about three seconds.

3When you see RESET? appear in the display, press ‘ST –’.

OK? shows in the display.

4Press SOUND RETRIEVER to confirm. OK appears in the display to indicate that the receiver has been reset to the factory settings.

Switching the speaker impedance

We recommend using speakers of 8 Ω with this system, but it is possible to switch the impedance setting if you plan to use speakers with a 6 Ω impedance rating.

•With the receiver in standby, press STANDBY/ON while holding down the SPEAKERS button.

Each time you do this, you switch between the impedance settings:

•SP 6 OHM – Use this setting if your speakers are rated at 6 Ω.

•SP 8 OHM – Use this setting if your speakers are rated at 8 Ω or more.

Note

1• If your display only has one HDMI terminal, you can only receive HDMI video from the connected component.

•Depending on the component, audio output may be limited to the number of channels available from the connected display unit (for example audio output is reduced to 2 channels for a monitor with stereo audio limitations).

•If you want to switch the input source, you’ll have to switch functions on both the receiver and your display unit.

•Since the sound is muted on the display when using the HDMI connection, you must adjust the volume on the display every time you switch input sources.

70

En

Page 69 Page 71
Image 70
Page 69 Page 71
Contents VSX-918V-S/-KVSX-818V-S/-K Important the Moulded Plug Operating EnvironmentVentilation Caution Contents Other connections Other SettingsControlling the rest of your system Additional informationChecking what’s in the box Before you startBefore you start Chapter Loading the batteriesIntroduction to home theater Minute guideMinute guide Chapter Listening to Surround SoundSwitch on the receiver and your TV 02 5 minute guideEnglish Deutsch Français Italiano Nederlands Español Minute guideEnter Other problems when using the Auto Mcacc Setup Better sound using Phase ControlPress Phase Phase Control to switch on phase correction Connecting up Chapter Connecting upMaking cable connections Receiver Connecting up Connecting a DVD player and TVUse a coaxial digital audio cable for the connection.1 VSX-918VItaliano Connecting upConnecting the multichannel analog outputs FrançaisAbout the WMA9 Pro decoder Connecting up Connecting other audio componentsCD-R, MD, DAT, Tape recorder, etc Connecting an HDD/DVD recorder, VCR and other video sources DeutschUse a three-way component video cable for the connection Connecting up Using the component video jacksConnecting using Hdmi Component 1 DVD Component 2 TV Component 3 DVRAbout Hdmi Connecting up Connecting to the front panel audio mini jack Connecting to the front panel video terminalTo improve FM reception Connecting up Connecting antennasUsing external antennas To improve AM receptionConnecting up Connecting the speakers AntennaTwist exposed wire strands together Hints on speaker placementBare wire connections Tighten terminalSwitching the speaker system Speaker placement diagramsFollowing illustrations show 5.1 channel speaker setups Front panel Controls and displaysControls and displays Chapter 14 15 16Controls and displays DisplayPRO Logic AnalogDTS VIR. SBControls and displays Remote control Level + Master Volume +Setup AV ParameterTuner Disp AccessSignal SEL ClassTV CH + Operating range of remote controlTV Control buttons TV VOL +Auto playback Listening to your systemListening to your system Chapter Listening in surround soundListening to your system Using the Advanced surround effectsPress ADV Surr repeatedly to select a listening mode Listening in stereoUsing Stream Direct Listening to your system Using Front Stage Surround AdvanceUsing the Sound Retriever Using Virtual Surround Back VSB Setting Listening to your system Setting the AV optionsWhat it does Options Setting What it does Options CH1Listening to your system Playing other sources Choosing the input signalPress Portable SHIFT+iPod USB on the remote control Selecting the front audio inputsUsing the System Setup menu System Setup menuSystem Setup menu Chapter Manual Mcacc speaker setupSelect ‘Fine Ch Level’ from the Manual Mcacc setup menu System Setup menuSelect ‘Manual MCACC’ from the System Setup menu Fine Channel LevelFine Speaker Distance Select ‘Fine SP Distance’ from the Manual Mcacc setup menuVolume increases to the reference level After pressing ENTER, test tones will be outputCopying your Acoustic Calibration EQ settings Setting the Acoustic Calibration EQ automaticallyAcoustic Calibration EQ Select ‘OK’ to copy and confirm Setting the Acoustic Calibration EQ manuallySelect the channels you want and adjust to your liking Might distort. If this happens, bringSpeaker Setting Manual speaker setupChecking your Acoustic Calibration EQ settings Select ‘Speaker Setting’ from the Manual SP Setup menu Crossover NetworkSelect ‘Channel Level’ from the Manual SP Setup menu Select ‘Crossover Network’ from the Manual SP Setup menuAdjust the level of each channel using Select a setup optionAdjust the distance of each speaker Using Select ‘Speaker Distance’ from the Manual SP Setup menuSpeaker Distance Tuning directly to a station Using the tunerUsing the tuner Chapter Listening to the radioListening to station presets Using the tuner Saving station presetsNaming station presets English DeutschSearching for RDS programs Using the tuner An introduction to RDSDisplaying RDS information Press FM to select the FM band.3 Press PTY SearchUsing the tuner Using EONMaking recordings Chapter Making recordingsMaking an audio or a video recording Controlling the rest of your system Chapter Setting the remote to control other componentsControlling the rest of your system Operating other Pioneer componentsClearing all the remote control settings Use the number buttons to enter the preset codeButtons Function Components Controlling the rest of your system Controls for TVsSHIFT+ ENTER/DISC Controlling the rest of your systemControls for other components Function ComponentsSHIFT+ Edit Return DiscEnter Return Shift +Controlling the rest of your system Preset Code List DVD RecorderOther connections Connecting an iPodConnecting your iPod to the receiver Other connections ChapterFinding what you want to play Other connectionsIPod playback Basic playback controlsSymptom What it means Connecting a USB deviceSwitching the iPod controls1 Press iPod Ctrl to switch the iPod controls.2Connecting your USB device to the receiver Basic playback controlsOther compatibility information Selecting a file from the folder/file list for playbackCompressed audio compatibility USB ERR What it meansAbout MPEG-4 AAC Using this receiver with a Pioneer flat screen TVAbout WMA Using the SR+ mode with a Pioneer flat screen TV Front panel display shows SR+ on or OFFInput Assign menu Other SettingsOther Settings Chapter Assigning the digital inputsAssigning the component video inputs Other SettingsAssigning the Hdmi inputs Select ‘Other Setup’ then press Enter Other Settings Other Setup menuSR+ Setup for Pioneer flat screen TVs Select the ‘PDP Volume Control’ setting you wantAdditional information TroubleshootingProblem Remedy Additional information ChapterAdditional information VSX-918V model only The SRSymptom Remedy HdmiConfiguration1 Resetting the main unitSwitching the speaker impedance Important information regarding the Hdmi connectionCleaning the unit Additional information Changing the TV format settingPower cord caution Amplifier sectionFM Tuner Section Component video sectionHdmi Section AM Tuner SectionPioneer Corporation Printed XRB3091-A

VSX-818V-K, VSX-918V-K specifications

The Pioneer VSX-918V-K and VSX-818V-K are both exemplary models in Pioneer’s range of home theater receivers, designed to deliver exceptional audio and video performance. These receivers highlight Pioneer's commitment to providing rich, immersive sound for a variety of entertainment formats.

One of the most significant features of the VSX-918V-K is its advanced 7.1 channel surround sound capability. This allows for a true multi-channel experience, making it an ideal choice for movie enthusiasts and gamers who seek depth and clarity in their audio. The VSX-818V-K, while being slightly less powerful with a 7.1 channel setup, still provides excellent audio performance with its clean and dynamic sound output, ensuring an engaging home cinema experience.

Both models are equipped with Pioneer’s latest Auto Room Tuning technology, which customizes the sound based on the room’s acoustics. This system utilizes a microphone and advanced algorithms to analyze the sound environment, adjusting settings to optimize performance. As a result, users can enjoy balanced audio whether they are in a small living room or a large theater space.

Another impressive feature is the incorporation of HDMI 1.3a support in both receivers, enabling high-definition audio and video passthrough. This capability ensures compatibility with the latest Blu-ray players, gaming consoles, and other HD devices. The receivers support various audio formats, including Dolby TrueHD and DTS-HD Master Audio, offering high-resolution sound that complements the latest film releases and video games.

In terms of connectivity, both the VSX-918V-K and VSX-818V-K feature multiple inputs, including composite and component video inputs, as well as optical and coaxial digital audio inputs. This extensive connectivity allows users to easily connect their devices and manage them through the intuitive on-screen GUI.

The models also boast a sleek design, with an appealing aesthetic that fits seamlessly into modern home theater setups. Their user-friendly interfaces and remote controls make navigation easy, ensuring that even non-technical users can enjoy a premium audio-visual experience.

Overall, the Pioneer VSX-918V-K and VSX-818V-K provide a robust set of features, ensuring outstanding audio fidelity and versatility, making them excellent choices for anyone looking to enhance their home entertainment systems.
Top Page Image Contents