1 | 2 | 4 | 2 |
| 5 |
| 7 | 8 |
|
| 9 |
|
| 11 |
|
| 12 | 14 |
| GAIN |
| VOLUME | 1 |
| GAIN | VOLUME | 2 | TREBLE |
| BASS | MIDDLE | REVERB | |||||
| 5 |
| 5 |
|
| 5 | 5 |
|
| 5 |
| 5 |
| 5 | 5 | POWER | ||
INPUT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
0 |
| 10 | 0 | 10 |
| 0 | 10 | 0 | 10 |
| 0 | 10 | 0 | 10 | 0 | 10 | 0 | 10 |
|
| BOOST |
|
| CHANNEL |
|
| BRIGHTNESS |
|
|
|
|
|
| Traynor Guitar Amplifier |
| STANDBY | |
|
|
|
|
| SELECT |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| 3 |
|
| 6 |
|
| 10 |
|
|
|
|
|
|
|
|
| 13 |
15 | 16 |
CAUTION: REPLACE WITH |
|
SAME TYPE FUSE AND RATING |
|
ATTENTION: UTILISER UN FUSIBLE DE |
|
RECHANGE DE MEME TYPE ET CALIBRE |
|
| ON |
•
UALITY Q
&
I
N
N
| 17 |
|
OV | MODEL TYPE:YS1006 | |
|
| |
A | 230V | 120VAC |
O | ||
T |
|
|
I | 50Hz 0,25A | 60Hz 0.5A |
• | ||
N |
|
|
| FUSE: T400mAL | FUSE: T1.0A sloBlo |
| EFX / LINE |
|
18 | 19 | |
CH. SELECT | EXT. SPKR | |
/ BOOST | ||
|
20 21
PHONES | DI OUT |
DESIGNED & MANUFACTURED BY
YORKVILLE SOUND • Toronto, CANADA
AVANT
Custom Valve
20
TRAYNOR YCV20 II
• |
|
|
|
| • |
E |
|
|
|
| 3 |
S |
|
| 6 | ||
| T | 9 |
| ||
|
| ABLISHED1 |
|
| |
INT. SPKR
POWER SERVICING! L’APPEREIL COUVERCLES!
PREAMP 
12AX7 | SPLITTER | 12AX7 |
V2 |
| V1 |
| 12AX7 |
|
| V3 |
|
POWER
THIS UNIT MUST BE GROUNDED!
CET APPAREIL DOIT ETRE MIS Á TERRE!
SENDRTN
FOOTSWITCH
DEFEAT
DISCONNECT BEFORE DEBRANCHER D’ENLEVER LES
POWER | POWER |
6BQ5 | 6BQ5 |
V4 | V5 |
Chassis Layout
Top
1.Input jack –
2.Channel 1 Gain and Volume Controls.
3.Channel 1 Boost Switch – Activates the boost circuitry.
4.Boost LED – Illuminated Red when the boost is active.
5.Channel 1 Indicator LED – Illuminates Yellow when active.
6.Channel Select Switch – Channel 1 is optimized for lead, Channel 2 for clean
7.Channel 2 Gain Control.
8.Channel 2 Volume Control.
9.Channel 2 Indicator LED – Illuminates Green when active.
10. Channel 2 Brightness Switch – Add sparkle to your clean sound.
11. Main Tone Controls – Treble, Bass, and Middle.
12. Reverb Control – Adjusts the Accutronics® reverb level for both channels.
13. Standby Switch – Activates standby mode to keep the tubes warm while the amp is not in use. 14. Power Indicator Jewel – Illuminates Red when in Active mode, and Yellow when in Standby mode.
Rear
15. Fuse and Power Cord
16. Power Switch.
17. Send / Return (Efx/Line) jacks –
18. Channel Select Footswitch jack – uses a
19.External Speaker jack and selectable defeat.
20.Headphone jack.
21.D.I. Output for connections straight to the 'board.