| 4 |
| 5 |
1 | 2 | 2 |
|
1 | GAIN | VOLUME | TREBLE |
5 | 5 | 5 | |
INPUT |
|
|
|
|
|
|
| 9 |
|
|
|
|
|
6 |
|
| 8 |
| 11 |
| 12 | 13 | 15 |
BASS | MIDDLE | 2 | VOLUME | TREBLE | BASS | MIDDLE | MASTER VOLUME | REVERB |
|
5 | 5 | 5 | 5 | 5 | 5 | 5 | 5 | POWER | |
|
|
|
|
|
|
|
|
|
0 | 10 | 0 | 10 | 0 | 10 | 0 | 10 | 0 | 10 | 0 | 10 | 0 | 10 |
| 0 | 10 | 0 | 10 | 0 | 10 | 0 | 10 |
| |||
|
|
| BOOST |
|
|
|
|
|
|
|
| CHANNEL |
|
|
|
| BRIGHTNESS |
|
| Traynor Guitar Amplifier |
|
|
|
| STANDBY | |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||
|
|
|
|
|
|
|
|
|
|
|
| SELECT |
|
|
|
|
|
|
|
|
|
|
|
|
| |
3 | 7 | 10 | 14 |
MODEL TYPE:YS1003 | 230V |
Z359BR / 1v4 | |
| 50Hz 0.5A |
| FUSE: T800mA |
| ON |
DISCONNECT POWER | POWER |
BEFORE SERVICING! | |
DEBRANCHER L’APPEREIL AVANT |
|
D’ENLEVER LES COUVERCLES! |
|
16 17
120VAC
60Hz 1.0A FUSE: T2.0A sloBlo
|
|
|
| SEND | RTN | CH. SELECT |
|
|
|
| / BOOST | ||
|
|
|
| |||
CAUTION: REPLACE WITH |
|
|
| |||
SAME TYPE FUSE AND RATING |
|
|
| |||
ATTENTION: UTILISER UN FUSIBLE DE | EFX / LINE |
| FOOTSWITCH | |||
RECHANGE DE MEME TYPE ET CALIBRE |
| |||||
THIS UNIT MUST BE GROUNDED!
CET APPAREIL DOIT ETRE MIS Á TERRE!
18 19
SPLITTERPREAMP
12AX7 | 12AX7 |
| 12AX7 |
V3 | V2 |
| V1 |
DISCONNECT POWER WHEN | POWER | ||
REPLACING TUBES | EL34 | EL34 | |
DÉBRANCHÉ L’APPAREIL AVANT | |||
DE REMPLACER LES LAMPES | V5 | V4 | |
EXTENSION
SPEAKER
|
|
| TY & IN | N |
|
|
|
| LI | OV | |||
| A |
|
| |||
| U |
|
|
| A | |
| Q |
|
|
|
| O |
|
|
|
|
|
| T |
• |
|
|
|
|
| I |
|
|
|
|
| N | |
|
|
|
|
|
| • |
| • |
|
|
|
| • |
| E |
|
|
|
| 3 |
| S |
|
| 6 | ||
|
| TA | BLIS HED | 19 |
| |
DESIGNED & MANUFACTURED BY
YORKVILLE SOUND • Toronto, CANADA
Custom Valve
50
TRAYNOR YCV50
20
Chassis Layout
Top
1Input jack – 1/4 inch phone jack.
2Channel 1 Gain and Volume Controls.
3Channel 1 Boost Switch – Activates the boost circuitry.
4Boost LED – Illuminated Red when the boost is active.
5Channel 1 Indicator LED – Illuminates Yellow when active.
6Channel 1 Tone Controls – Treble, Bass, and Middle.
7Channel Select Switch – Channel 1 is optimized for lead, Channel 2 for clean sound
8Channel 2 Volume Control.
9Channel 2 Indicator LED – Illuminates Green when active.
10Channel 2 Brightness Switch – Add sparkle to your clean sound.
11Channel 2 Tone Controls – Treble, Bass, and Middle.
12Master Volume – Controls the overall level of the amplifier.
13Reverb Control – Adjusts the Accutronics® reverb level for both channels.
14Standby Switch – Activates standby mode to keep the tubes warm while the amp is not in use.
15Power Indicator Jewel – Illuminates Red when in Active mode, and Yellow when in Standby mode.
Rear
16Fuse and Power Cord
17Power Switch.
18Send / Rtn (Efx/Line) jacks – 1/4 inch phone Input and Output jacks.
19Channel Select Footswitch jack – uses a 1/4 inch TRS standard latching