Nady Systems UHF24HT1112 owner manual UHF-24 Receiver

Page 4

UHF-24 RECEIVER

Rack-mounting the Receiver

There are two options available for rackmounting the UHF-24 Dual Channel Receiver: single or side-by-side with another UHF-24 receiver.

a. Single mounting: Remove the SIDE MOUNT CLIPS (1) from each side of the receiver and slide in the optional ERM-3 RACK EARS (2)

b. Side-by-side double mounting: After removing the SIDE MOUNT CLIPS (1) from each side of the receivers, join the two receivers with the EJC-3 JOINING CLIPS (3) and slide in the

ERM-33 EARS (4)

(Note: Do not mount the receiver in a rack directly above an amplifier or other source of high heat. This could degrade the performance of the UHF-24 receiver. Always ensure adequate airfl ow and heat dissipation in any rack confi guration.)

Antennas

The UHF-24 receiver is equipped with DUAL TELESCOPIC RETRACTABLE ANTENNAS (5) These should be extended fully to obtain maximum range. The optimal antenna positions are 45 degrees from the receiver and 90 degree from each other. For maximum range, it is always best to maintain a line of sight (no obstruction) between the receiver antennas and the transmitter at all time whenever possible.

Powering the Receiver

Powering the receiver by plugging the provided DC ADAPTOR (15VDC/0.4A) PLUG (15) into the DC INPUT JACK (14) on the back of the receiver. Then plug the adapter into an AC outlet. (Note: Any 15VDC/0.4A capacity AC/DC adapter can also be used.) Turn VOLUME CONTROLS (10) of all channels to counter-clockwise for minimum setting. Once the receiver is connected to a power source, push the POWER SWITCH (7) to the ON position. The POWER LED (6) will light up. The received signal CH. A OR B LEDs (8) and 5-SEGMENT AF LED (9) indicators on the front panel of the receivers will not light up at this time, until one or more of the two channels is receiving a signal from your system’s transmitters.

Mute (Squelch) Adjusting

In normal operation of the UHF-24 receiver, the mute control for each channel A or B should be set fully clockwise to the factory preset of 1uV RF level for maximum sensitivity. Doing so sets each receiver for maximum range. However, in case of high RF activity, the mute levels should be read- justed to compensate for the adverse conditions in a particular location. If, with a transmitter turned off, one or more LEDs of the corresponding receiver for that transmitter fl icker or stay on, the MUTE (SQUELCH) CONTROL (12) of the corresponding channel should be turned counterclockwise until the LEDs extinguish. For each of the two channels, when the mute (Squelch) is properly adjusted, the corresponding TX LED displays will light only when the system’s transmitter is turned on. Turn- ing the mute (Squelch) counter clockwise too far will result in reducing range, but yield a quieter mute function during dropout or at the end of the operating range.

Note: If you turn on the transmitter of only one channel within 10 feet of the receiver, both CH. A or B LEDs may come on. This is normal and due to the receiver’s high sensitivity. This does not indi- cate a problem and operation with both transmitters on will be unaffected. Proper operation of the MUTE CONTROL (12) (counterclockwise) will extinguish the LED that is affected by the transmitter of the other channel. This will also reduce range.

Audio Level and Peak LED indicator

The UHF-24 receiver is equipped with a 5-segment LED AF LEVEL (9) display for each channel. The red LED on the right of these displays is the audio peak indicator. Note: That the peak red LED will light with a strong audio signal from the transmitter. Occasional fl ickering of the peak LED on loud input signals to the transmitter is normal. However, If the peak LED lights continuously, the volume into the transmitter should be decreased or audio distortion may result.

CAUTIONS AND TROUBLESHOOTING

Feedback

Observe care in selecting P.A. volume, transmitter location and speaker placement so that the acoustic feedback (howling and screeching) will be avoided. Please also note the pickup pattern characteristics of the microphone selected. Omni directional mics pick up sound equally from all direction, and are prone to feedback if not used carefully. Unidirectional mics are more resistant to feedback. However, pick up sound source best that are directly in front of the mic. Also mics that arefarther from the sound source, such as lavalier, required more acoustic gain and thus are also more prone to feed back than close-source mics such as handheld or headworn models that are used close to the mouth.

Microphone Damage

Headset and lavalier mic users, note that the microphone element can easily be destroyed by the buildup of salts and minerals from perspiration and saliva. It is good practice to put a windscreen on the mic at all time to protect it.

No Audio

If you not getting audio through the system, carefully recheck all setup procedures. The receiver and transmitter must be on the same RF channel (frequency).

RF Interference

If you encounter receiving interference (from other than an operating TV station), often it can be overcome by adjusting the receiver ‘s MUTE (squelch) control. Please note that wireless frequen- cies are shared with other radio services. According to FCC regulations, wireless microphone operations are unprotected from interference from other licensed operations in the band. If any interference is received by any Government or non-government operation, the wireless microphone must be cease operation or change frequencies. The above statement is valid only for use in the U.S.A.

4

13

Image 4
Contents UHF-24 Table of Contents Using this ManualSpecifications IntroductionSystem Features TipsUHF-24 Receiver Receiver Volume Controls Adjust Level Trim AdjustConnecting Audio Outputs Link 4 PLUG-IN TransmitterTransmitters Set Up Handheld Microphone InstallationLavalier Microphone Installation Microphone OperationUH-4 Handheld Transmitter UB-4 Bodypack TransmitterTransmitter Operation Input Connection and Input Selector Switches UH-4 Handheld Transmitter UB-4 Bodypack Transmitter