Transmitters Set Up

UHF-24 RECEIVER

internal Tone Squelch defeat feature. Contact your Nady dealer or Nady Systems Customer Service for details.)

Note:

•Even though your system has Tone Squelch™, it’s always best to keep the volume controls of unused channels, (with corresponding transmitter off) turned off in the ampliﬁer or the mixer. The audio should only be “live” if the transmitter is on.

•As when making any connection, make sure the connected ampliﬁ er or mixing board volume is at the minimum level before plugging in the receiver to avoid possible sound system damage.

•Only one transmitter can be used with one receiver channel. It is not possible to use two transmit- ters on the same frequency and mix the output of these transmitters into one wireless receiver channel. The dual receiver UHF-24 can thus be only used with two transmitters on the same frequencies as the two receiver channels.

CH A

CH. B

8 9 8 9

10	11	12	15
			1

LINK 4™ PLUG-IN TRANSMITTER

The LINK-4 transmitter requires a single 9V battery to operate. To open the battery compartment, slide BATTERY DOOR (31 ) downward to open the cover, exposing the BATTERY HOLDER (32) Insert a fresh 9V battery according to the correct polarity as indicated on the transmitter body. Slide back the door onto the original position. Make sure the cover is secured completely. Fresh Alkaline batteries can last up to 10 hour of operation, but in order to ensure optimum performance, it is recommended that the batteries should be replaced after 6-8 hours of use.

Handheld Microphone Installation

Step 1 Rotate the transmitter’s threaded LOCKING RING (33) counter-clockwise inward the transmitter body until it stops.

Step 2 Hold your mic in one hand and the LINK 4 in other.

Step 3 Place your mic into the XLR CONNECTOR (34) and push your mic all the way down untill a click sound.

Step 4 Lock the mic into place with the adjustable threaded LOCKING RING (33) by rotating the ring clockwise, to the top of the transmitter

Step 5 To release the XLR CONNECTOR (34) , turn the treaded LOCKING RING (33) counter- clockwise and press the RELEASE BUTTON (39)

Lavalier Microphone Installation

You will need a male XLR to mini male XLR adaptor (Switch-Craft TA-4 or equivalent) to use a lavalier microphone per the installation instructions. Then plug the lavalier microphone’s mini male XLR into the adapter. The PHANTOM POWER SWITCH (35) should be turned ON for use with a condenser lavalier mic which requires external phantom powering.

Note: The lavalier microphone you are using must terminate with a mini XLR or full XLR connector and conﬁ rm to the pin assignments shown below. If they do not, the lavalier mic may not work with the LINK 4. If you have any questions, please contact your Nady dealer or Nady Systems Service Department.

The pin assignments on the LINK 4 XLR connector are as shown:

1 Ground

XLR	3		680	Phantom Volt. (full 9V battery
XLR		3 9V		Phantom Volt. (full 9V battery
Connector	1 2	3 9V		voltage) switchable
Top View			680

2Mic

9VInput

Microphone Operation

To turn it on, slide the OFF/STANDBY/ON SWITCH (36) to the STANDBY position ﬁ rst (transmit- ter on, audio muted) or the ON position (transmitter and audio both on). You could also use your hardwire microphone audio mute switch afterward. The BATT LOW INDICATOR LED (37) will give a single ﬂ ash in red, indicating usable battery strength. In case of dead or low battery, the LED will either not go on at all or will stay on continuously, indicating that the battery should be replaced with a fresh one. To preserve battery life, turn the transmitter off when not in use. To turn off, slide the OFF/STANDBY/ON SWITCH (36) to OFF position. No LEDs will light up. The unit is now off.