Pioneer VSX-AX5Ai-S, VSX-AX5Ai-G manual Settings, Display

Page 99

Additional information

12

Symptom

Cause

Remedy

 

 

 

Screen noise when playing back • The video source signal has a problem. a video source.

•If your video connections use mixed cable types (for example RCA standard video to a component video connection), you may want to try connecting your system using only one cable type (for example, use RCA standard video cable for all connections).

Can’t record video.

• You are trying to record a source connected

• Connect the source component to either the composite

 

to the component video jacks.

video or the S-video jacks (see Connecting your equipment

 

 

on page 15).

 

 

 

 

• The source is copy protected.

• You can't record sources that have been copy protected.

 

 

 

 

• The recorder's video input is hooked up

• Hook up the source and the recorder using the same

 

using a different type of cable to the source

type of video cable (see Making an audio or a video

 

video output.

recording on page 66).

 

 

 

Settings

Symptom

Cause

The Auto Surround Setup

• The ambient noise level in the room is too

continually shows an error.

high, or obstacles are blocking the setup

 

microphone.

Remedy

•Keep the noise level in the room as low as possible when using the Auto Surround Setup (see Other problems when using the Auto Surround Setup on page 14 for more on this). If the noise cannot be kept low enough, you will have to set up the surround sound manually (page 54).

After using the Auto Surround

• There was some inaudible low-frequency

• The low-frequency noise could have been caused by an

Setup, the speaker size setting

noise in the room.

air conditioner or motor. Switch off all appliances in the

(LARGE or SMALL) is incorrect.

 

room and rerun the Auto Surround Setup.

 

 

 

The display shows KEY LOCK

• Your Pioneer dealer has enabled the key

• Ask your Pioneer dealer to disable the key lock.

ON when you try to make

lock feature.

 

settings.

 

 

 

 

 

Display

Symptom

Cause

Remedy

 

 

 

The display is dark or off.

• The display is set to dark or off.

•Press DIMMER on the remote control repeatedly to select a different brightness.

After making an adjustment the

• The display is set to off.

• Press DIMMER on the remote control repeatedly to

display goes off.

 

select a different brightness.

 

 

 

You can't get DIGITAL to display

• There is a problem with the digital

• Check your digital connections and/or assign the digital

when using the SIGNAL SELECT

connections or the digital input is assigned

inputs correctly (see Assigning the digital inputs on

button.

incorrectly.

page 81).

 

 

 

 

• The multichannel analog inputs are

• Press MULTI CH INPUT again (see Using the

 

selected.

multichannel analog inputs on page 42).

 

 

 

The Dolby/DTS indicator doesn't

• The player is paused.

• Press play.

light when playing Dolby/DTS

 

 

• The player's sound output settings are

• Set the player correctly (consult the manual that came

software.

wrong.

with the player, if necessary).

 

 

 

 

When playing a DVD-Audio disc,

• The audio from these discs is output from

• This is not a malfunction. See also the operating

the DVD player display shows 96

the analog audio jacks of the DVD player only;

instructions that came with your DVD player.

kHz. However, the receiver’s

the receiver does not show the sampling rate

 

display does not.

of the input signal through the analog inputs.

 

 

 

 

During playback of a DTS 96/24

• The receiver’s input signal type is set to

• Set the receiver to AUTO or DIGITAL (see Selecting the

source, the display doesn't show

analog.

input signal type on page 43).

96kHz.

 

 

 

 

 

99

En

Page 98 Page 100
Image 99
Page 98 Page 100
Contents VSX-AX5Ai-SVSX-AX5Ai-G Risk of Electric Shock Do not Open Operating EnvironmentInformation to User Voltage selectorContents Additional information Controlling other equipment Advanced setupUsing other functions Other connectionsBefore you start Chapter FeaturesChecking the supplied accessories Before you startOpening the front panel Installing the receiverUsing the remote control Before you startRemote control battery indicator Operating range of the remote controlIntroduction to home theater Setting up for Surround SoundMinute guide Minute guide ChapterConnect your speakers 02 5 minute guideUse the on-screen Auto Surround setup to set up your system Minute guideLarge ‘SurrBack System’ should be highlighted. Press Switch on the receiver and your TV‘Surround Setup’ should be highlighted. Press Enter‘Auto Setting’ should be highlighted. Press Make sure ‘Normal System’ is selected, then select ‘Exit’Follow the instructions on-screen Playing a source Checking the settings on your DVD or other playerOther problems when using the Auto Surround Setup If the receiver isn’t already on, switch on the powerConnecting your equipment Connecting your equipment ChapterRear panel About the video converter Connecting your equipmentDigital audio cables When making cable connectionsAbout cable types Analog audio cablesConnecting your equipment Connecting your TV DVD player Connecting your equipment Connecting a DVD playerVSX-AX5Ai Connecting the multichannel analog outputsSTB Connecting your equipment Connecting a VCR or DVD recorder Connecting your equipment Connecting other video sources DVD player Connecting your equipment Using the component video jacksConnecting your equipment Connecting digital audio sources Tape deck, etc Connecting your equipment Connecting analog audio sourcesPortable DVD player, etc Front left Center Front right Connecting your equipment Installing your speaker systemConnecting the speakers Bare wire connectionsPlacing the speakers AM loop antenna Connecting your equipment Connecting antennasFM wire antenna Connecting external antennasOutdoor antenna Indoor antenna Vinyl-coated wire Meters Plugging in the receiverAbout the AC outlet Controls and displays Controls and displays ChapterFront panel Controls and displays BASS/TREBLE Mcacc Setup MIC jackTone Control ToneTuned Controls and displays DisplayControls and displays Remote control Movie / Music Remote SetupAudio TV InputListening to your system Listening to your system ChapterAuto playback Listening in surround sound Advanced effect modes Listening to your systemMovie listening modes Basic modesDolby Pro Logic IIx Music settings Music listening modesPro Logic IIx Music See above Listening in stereo Listening with headphonesAdjusting the advanced effect level Neo6 Music settingsListening with Acoustic Calibration Listening to your system Selecting the input signal type NEO6 Listening to your system Using the surround back channelOn the remote control, press RECEIVER, then press HI-BIT Using the audio scaler for Hi-bit and Hi-samplingTreble Using the tone controlSwitching the tone control on or off Adjusting the bass and trebleRelease the button when you see the setting you want Reducing noise during playbackListening to dual mono soundtracks Finding a station Using the tunerUsing the tuner Chapter Tuning directly to a stationMPX mode Using the tunerListening to memorized station presets Naming station presetsAbcdefghijklmnopqrstuvwxyz Using the tuner An introduction to RDS Press Disp Mode to select the RDS information displayDisplaying RDS information Searching for RDS programs Using EONPress EON Mode to select one of the possible modes An introduction to EONPress and hold EON Mode for about two seconds Clearing all stations from the RDS and EON searchesPress Enter Select the setting you want to adjust Surround Setup menuSurround Setup menu Chapter Making receiver settings from the Surround Setup menuSpeaker Setting Surround Setup menuSurround back speaker setting Normal surround settingChannel Level Select ‘Channel Level’ from the Normal setup menuSpeaker Distance Select ‘Speaker Distance’ from the Normal setup menuControlling other equipment Chapter Using the remote control with other componentsRecalling preset codes Controlling other equipmentControlling other equipment Programming signals from other remote controlsDisc Controlling other equipment Controls for TVsMenu GuideMode Controlling other equipment Controls for other componentsSubtitle DispExit TOPRepeat steps 2-4 for as many components as you want Controlling other equipment Direct functionMulti Operation and System Off Programming a multi-operation or a shutdown sequenceUsing multi operations To add or change a command select ‘Change’ and press EnterPress Multi Operation Switching components on and off using the 12 volt trigger Using System offOperating other Pioneer components with this unit’s sensor Making an audio or a video recording Using other functionsUsing other functions Chapter Adjusting the delay of a soundtrackDimming the display Enhancing Sacd playbackEditing remote control display names Using other functionsSwitching the speaker impedance Advanced remote control featuresClearing remote control settings Adjusting the remote control backlightUsing other functions Resetting the system Other connections Chapter Second Zone speaker B setupSwitching the speaker system Other connectionsSpeaker Bi-wiring your speakersOther connections Bi-amping your front speakers Front leftMaking multi-room connections Basic multi-room setupSurrBack System multi-room setup Other connections Multi-room listeningPress Control Using the multi-room controlsUse the Master Volume dial to adjust the volume Other connectionsOther connections Connecting additional amplifiersOther connections Using the i.LINK interface Other connections About i.LINK About Pqls rate controlCreating an i.LINK network Other connections Using the USB interface Press Input on the remote control repeatedly to select USBConnect your computer’s USB terminal to Other connections Connecting a PC for Advanced Mcacc output Advanced Mcacc output using your PCSelect ‘PC Output’ and press Enter Select the setting you want to adjust then press Advanced setupAdvanced setup Chapter System Setup menuAssigning the digital inputs Advanced setupTHX Cinema Setup Input Assign menuSelect ‘Component-In Select’ from the Input Assign menu Assigning the component video inputsAssigning the i.LINK inputs Component-1 OFF Component-2 OFFSelect ‘Function Rename’ from the System Setup menu Function RenameSelect the name of the input you want to rename PHONO/LINE Setup Sacd SetupVolt Trigger Multi-Room and IR receiver setupSelect ‘Expert’ then press Enter Advanced setup Expert setup menuCrossover Network Select ‘Crossover Network’ from the Expert setup menuSelect ‘Fine Channel Level’ from the Expert setup menu Adjust the level of the left channelFine Channel Delay Setting the Acoustic Calibration EQ automaticallyAcoustic Calibration EQ Front Align Setting the Acoustic Calibration EQ manuallySelect CUSTOM1 Adjust or CUSTOM2 Adjust Select the channels you want and adjust to your likingSelect ‘Exit’ to copy and confirm Copying your Acoustic Calibration EQ settingsChecking your Acoustic Calibration EQ settings Select ‘DATA COPY’ then press EnterHow to use Professional Acoustic Calibration How to interpret the graphical outputProfessional Acoustic Calibration If you selected ‘Auto Pro.’, select ‘Start’ and press Using Professional Acoustic CalibrationSelect a setup option Select ‘Professional’Bass Peak Level Select ‘Bass Peak Level’ from the Expert setup menuSelect ‘D-Range Control’ from the Expert setup menu Choose the setting that you wantDynamic Range Control Additional information Chapter TroubleshootingPower Additional informationNo sound Additional informationDigital inputs on Other audio problemsVideo Symptom CauseDisplay SettingsPRO Logic II or Neo6 Remote controlLink messages Link interfaceMaintenance of external surfaces Changing the frequency stepUSB interface Dolby Additional information Surround sound formatsAdditional information About THX DVR Additional information Preset code brandsDVD CD-RAdditional information Specifications European model Continuous Power Output Additional information Specifications Multi-voltage modelPioneer Corporation

VSX-AX5Ai-S, VSX-AX5Ai-G specifications

The Pioneer VSX-AX5Ai-S and VSX-AX5Ai-G are standout home theater receivers known for their robust performance and advanced features that cater to audio enthusiasts and casual listeners alike. Designed with a focus on versatility and high-fidelity audio reproduction, these receivers deliver exceptional sound quality for both music and movies.

One of the most significant features of the VSX-AX5Ai series is its powerful amplification system. With a capacity to drive multiple channels, these receivers provide dynamic sound and enough power to fill even large spaces. The Class D3 amplification technology used in these models ensures efficient performance, producing clean and distortion-free audio. This technology contributes to higher energy efficiency while providing rich bass and clear highs.

These receivers are equipped with advanced audio codecs, including Dolby Atmos and DTS:X, which create an immersive surround sound experience. The ability to decode high-definition audio formats enhances the listening experience, bringing movie soundtracks and music to life with precision and depth. The multi-channel setup allows for easy integration into existing home theater systems, delivering a cinematic atmosphere at home.

Another notable feature is the MCACC (Multi-Channel Acoustic Calibration System). This automatic calibration system optimizes speaker settings based on the room's acoustics, ensuring that users achieve the best possible sound from their speaker setup. It analyzes the acoustics and adjusts the receiver's settings to provide a balanced and harmonious sound profile.

Connectivity is a highlight of the VSX-AX5Ai-S and VSX-AX5Ai-G. They come equipped with multiple HDMI inputs and outputs, allowing users to connect various devices, such as Blu-ray players, gaming consoles, and streaming devices. The presence of digital and analog audio inputs ensures compatibility with a wide range of audio sources. Furthermore, these models support video upscaling, enhancing lower-resolution content for improved playback quality.

The user-friendly interface and remote control make it easy to navigate settings and configurations, providing a seamless user experience. Additionally, both models support streaming services, allowing users to access their favorite music directly from apps over Wi-Fi.

In summary, the Pioneer VSX-AX5Ai-S and VSX-AX5Ai-G are exceptional receivers that combine powerful amplification, advanced audio processing, and user-friendly features. With technologies designed to optimize sound quality and provide versatile connectivity, these models are an excellent choice for anyone looking to enhance their home audio experience. Whether for movies, music, or gaming, they deliver a premium listening experience that stands out in the competitive home theater market.
Top Page Image Contents