Manuals / MGE UPS Systems / Computer Equipment / Power Supply

MGE UPS Systems Switched PDU Operations, Setting the outlet wakeup state, To set the wakeup state

Models: Switched PDU

1 62

Download 62 pages 5.96 Kb

Page 35

3. Operations

Setting the outlet wakeup state

The Set Outlet Wakeup command set the default wakeup state for that outlet. In the event of a system-wide power loss, this state will be applied to the outlet when power is restored.

The wakeup state may be set to On or Off. Upon restoration of system power; If set to On, the Switched PDU will apply power to that outlet. If set to Off, the Switched PDU will not apply power to that outlet.

To set the wakeup state:

At the Switched PDU: prompt, type set outlet wakeup, followed by on or off and the outlet name. Press Enter.

Example

The following command sets the wakeup state for outlet .a1 to off:

Switched PDU: set outlet wakeup off .a1<Enter>

Displaying outlet information

The Show Outlets command displays information about all outlets. This information includes:

•Descriptive outlet name, if applicable

•Outlet wakeup state setting

To display outlet information:

At the Switched PDU: prompt, type show outlets and press Enter.

Example

The following command displays all outlet information:

Switched PDU: show outlets<Enter>

Outlet	Outlet	Wakeup
ID	Name	State
.A1	DataServer_1	off
.A2	WebServer_1	on
.A3	FileServer_1	last
.A4		on
.A5		on
.A6		on
.A7		on
.A8		on
.A9		on
.A10		on
.A11		on
.A12		on
.A13		on
.A14		on
.A15		on
.A16		on

More (Y/es N/o):

301-0399-4 Rev A. - Page 35

Image 35

MGE UPS Systems Switched PDU user manual Operations, Setting the outlet wakeup state, To set the wakeup state, Example

Contents

E T N I N U E H T Switched PDU Installation and user manualLife-Support Policy InstructionsDangerous Voltage Protective Grounding TerminalOPERATIONS ContentsINSTALLATION GETTING STARTEDuser account prior to attachment to your network 1. Getting StartedQuick Start Guide Additional Required Items 2. InstallationStandard Accessories 1 Power Input 2 Input Current LED 3 Ethernet / RS232 Ports Equipment OverviewFigure 1. Unit Views 2. Installation2. Installation Safety PrecautionsInstalling the Power Input Retention Bracket Figure 2. Retention Bracket assemblyMounting Connecting to the Power SourceTo attach a power cord to the unit To connect to the power sourceSerial RS232 port Connecting DevicesConnecting the Sensors Connecting to the UnitPage C OMMAND L INE I NTERFACE 3. OperationsI NTERFACES HTML I NTERFACEOutlet Naming and Grouping Usernames and Passwords3. Operations InterfacesTo log in by HTML HTML InterfaceFigure 4. Example HTML page Logging In 3. OperationsOutlet State/Control State Field Values Outlet ControlIndividual GroupSensors ConfigurationEnvironmental Monitoring Input LoadSetting the IP address, subnet mask or gateway NetworkTelnet/SSH HTTP/SSLSetting the data-rate for the serial ports Serial PortsSetting the HTTP authentication method Setting SSL access levelChanging a user password OutletsGroups UsersAdding and Deleting serial port access Changing a user’s access privilege levelAdding and Deleting outlet access Adding and Deleting group accessTesting the FTP upload configuration SNTPSNMP Setting the filename for uploadLogging In Command Line InterfaceTools Restart3. Operations Operations Command SummaryAdministrative Command Summary 3. Operations To display the names of commands that you may executeAdministrative Command Summary continued 3. Operations Operations CommandsRebooting outlets To reboot one or more outletsExamples 3. OperationsDisplaying outlet status To display on/off status of one or more outletsTo display accessible groups Displaying accessible outletsTo display accessible outlets Displaying accessible groups3. Operations Displaying accessible serial portsTo display accessible serial ports Connecting to a serial deviceExample 3. OperationsDisplaying the status of the Environmental Monitor To display the status of the Environmental MonitorCreating a user account Administration CommandsUser Administration 3. OperationsTo set the access level privilege for a user Changing a passwordTo change a password Setting user access level privilegesTo grant outlet access to a user Displaying the access privilege levelsTo display user access privilege levels Adding outlet access to a userTo grant group access to a user Deleting outlet access for a userTo delete outlet access for a user Adding group access to a user3. Operations Group AdministrationDisplaying user outlet, group and serial port access To display user outlet, group and serial port accessTo add an outlet to a group Outlet Administration3. Operations Adding an outlet to a groupExample Setting the outlet wakeup state3. Operations To set the wakeup stateTo enable or disable active signal checking for serial connections Serial Port AdministrationSetting the serial ports data-rate Enabling or disabling active signal checking for serial connections3. Operations System AdministrationDisplaying system configuration information To display system configuration informationExamples 3. OperationsCreating a descriptive tower name To create a tower nameSetting the IP address TCP/IP AdministrationPerforming a warm boot To perform a warm bootTo enable or disable HTTP support HTTP AdministrationDisplaying network configuration information To display network configuration informationTo set the HTTP authentication method Telnet AdministrationFTP Administration Setting the HTTP authentication methodSetting the filepath for the file to be uploaded Setting the FTP PasswordTo set the FTP password Setting the filename to be uploadedTo display SNTP configuration information SNTP AdministrationSetting the SNTP server address Displaying SNTP configuration informationSSH Technical Specifications Enabling and Setting up SSL SupportSSL Technical Specifications Enabling and Setting up SSH SupportTo enable or disable SSL support SSL Command SummaryEnabling and Setting up SSL Support SSL Technical SpecificationsTo enable or disable SSH support SSH Command SummaryEnabling and Setting up SSH Support SSH Technical SpecificationsTo enable SNMP support SNMP Command SummaryEnabling and Setting up SNMP Support SNMPTo set the trap timer Setting trap destinationsTo reset the trap destination Setting the trap timerInfeed Status traps SNMP TrapsTrap Summary Tower Status trapsLoad traps Temperature/Humidity Sensor Status trapsOutlet Status traps Environmental Monitor Status trapsTemp Trap Temp trapsHumidity traps 4. Advanced OperationsEnabling or Disabling a Status trap Configuring Traps SNMP Trap Command SummaryTo Enable or Disable a Status trap 4. Advanced OperationsTo Enable or Disable the Temp trap To Enable or Disable a Load trapSetting the Infeed Load limit To Enable or Disable a Change trapSetting the Humidity sensor threshold limits Setting the Temperature sensor threshold limitsTo set the Temperature threshold limits To Enable or Disable the Humid trap4. Advanced Operations Displaying trap configuration informationTemperature/Humidity Sensor .A1 Temperature/Humidity Sensor .A2T ECHNICAL S PECIFICATIONS R ESETTING TO F ACTORY D EFAULTS5. Appendices U PLOADING F IRMWARETo reset to factory defaults using the reset button Resetting to Factory DefaultsTo reset to factory defaults from the HTML interface To reset to factory defaults from the command lineModels Europe/Asia Technical SpecificationsPower Ratings Physical SpecificationsTime-Delay Fuses - Class G LED IndicatorsData Connections Branch Circuit ProtectionPage