TCP/IP Administration, Operations | MGE UPS Systems Switched PDU

Displaying the firmware version

3. Operations

Displaying the firmware version

The Version command displays the firmware version.

To display the firmware version:

At the Switched PDU: prompt, type version and press Enter.

Performing a warm boot

The Restart command performs a warm boot of the Switched PDU.

NOTE: System user/outlet/group/port configuration or outlet states are NOT changed or reset with this command.

To perform a warm boot:

At the Switched PDU: prompt, type restart and press Enter.

TCP/IP Administration

NOTE: A restart of the Switched PDU is required after setting or changing ANY TCP/IP configurations. See Performing a warm boot for more information.

Setting the IP address

The Set Ipaddress command sets the TCP/IP address of the network interface controller.

To set the IP address:

At the Switched PDU: prompt, type set ipaddress, followed by the IP address and press Enter.

Example

The following command sets the IP address to 12.34.56.78:

Switched PDU: set ipaddress 12.34.56.78<Enter>

Setting the subnet mask

The Set Subnet command sets the subnet mask for the network the PT40 will be attached to.

To set the subnet mask:

At the Switched PDU: prompt, type set subnet, followed by the subnet mask and press Enter.

Example

The following command sets the subnet mask to 255.0.0.0

Switched PDU: set subnet 255.0.0.0<Enter>

Setting the gateway

The Set Gateway command sets the IP address of the default gateway the Switched PDU uses to access external networks.

To set the gateway IP address:

At the Switched PDU: prompt, type set gateway, followed by the gateway IP address and press Enter.

Example

The following command set the gateway IP address to 12.34.56.1:

Switched PDU: set gateway 12.34.56.1<Enter>

301-0399-4 Rev A. - Page 39

Image 39

MGE UPS Systems Switched PDU TCP/IP Administration, Operations, Displaying the firmware version, Performing a warm boot

Contents

E T N I N U E H T Switched PDU Installation and user manual Life-Support Policy InstructionsDangerous Voltage Protective Grounding Terminal OPERATIONS ContentsINSTALLATION GETTING STARTED 1. Getting Started Quick Start Guideuser account prior to attachment to your network 2. Installation Standard AccessoriesAdditional Required Items 4 Temperature / Humidity Ports Equipment OverviewFigure 1. Unit Views 1 Power Input 2 Input Current LED 3 Ethernet / RS232 Ports To install the power input retention bracket Safety PrecautionsInstalling the Power Input Retention Bracket Figure 2. Retention Bracket assembly Mounting Connecting to the Power SourceTo attach a power cord to the unit To connect to the power source Serial RS232 port Connecting DevicesConnecting the Sensors Connecting to the UnitPage C OMMAND L INE I NTERFACE 3. OperationsI NTERFACES HTML I NTERFACE Outlet Naming and Grouping Usernames and Passwords3. Operations Interfaces HTML Interface Figure 4. Example HTML page Logging InTo log in by HTML Outlet State/Control State Field Values Outlet ControlIndividual Group Sensors ConfigurationEnvironmental Monitoring Input Load Setting the IP address, subnet mask or gateway NetworkTelnet/SSH HTTP/SSL Setting the data-rate for the serial ports Serial PortsSetting the HTTP authentication method Setting SSL access level Changing a user password OutletsGroups Users Adding and Deleting serial port access Changing a user’s access privilege levelAdding and Deleting outlet access Adding and Deleting group access Testing the FTP upload configuration SNTPSNMP Setting the filename for upload Logging In Command Line InterfaceTools Restart Administrative Command Summary Operations Command Summary Administrative Command Summary continued To display the names of commands that you may execute Turning outlets on Operations CommandsRebooting outlets To reboot one or more outlets To display on/off status of one or more outlets Displaying outlet status To display accessible groups Displaying accessible outletsTo display accessible outlets Displaying accessible groups Displaying infeed status Displaying accessible serial portsTo display accessible serial ports Connecting to a serial device To start a new session Displaying the status of the Environmental MonitorTo display the status of the Environmental Monitor Starting a new session To create a user account Administration CommandsUser Administration Creating a user account To set the access level privilege for a user Changing a passwordTo change a password Setting user access level privileges To grant outlet access to a user Displaying the access privilege levelsTo display user access privilege levels Adding outlet access to a user To grant group access to a user Deleting outlet access for a userTo delete outlet access for a user Adding group access to a user Creating a group name Group AdministrationDisplaying user outlet, group and serial port access To display user outlet, group and serial port access Deleting an outlet from a group Outlet AdministrationAdding an outlet to a group To add an outlet to a group To display outlet information Setting the outlet wakeup stateTo set the wakeup state Displaying outlet information To enable or disable active signal checking for serial connections Serial Port AdministrationSetting the serial ports data-rate Enabling or disabling active signal checking for serial connections Creating a location description System AdministrationDisplaying system configuration information To display system configuration information To display tower information Creating a descriptive tower nameTo create a tower name Displaying tower information Setting the subnet mask TCP/IP AdministrationTo perform a warm boot Setting the IP address To enable or disable HTTP support HTTP AdministrationDisplaying network configuration information To display network configuration information To enable or disable Telnet support Telnet AdministrationFTP Administration To set the HTTP authentication method Setting the filepath for the file to be uploaded Setting the FTP PasswordTo set the FTP password Setting the filename to be uploaded To display SNTP configuration information SNTP AdministrationSetting the SNTP server address Displaying SNTP configuration information SSH Technical Specifications Enabling and Setting up SSL SupportSSL Technical Specifications Enabling and Setting up SSH Support To enable or disable SSL support SSL Command SummaryEnabling and Setting up SSL Support SSL Technical Specifications To enable or disable SSH support SSH Command SummaryEnabling and Setting up SSH Support SSH Technical Specifications To enable SNMP support SNMP Command SummaryEnabling and Setting up SNMP Support SNMP Setting the Trap community string To reset the trap destinationTo set the trap timer Setting the Get/Set community strings Infeed Status traps SNMP TrapsTrap Summary Tower Status traps Load traps Outlet Status trapsEnvironmental Monitor Status traps Temperature/Humidity Sensor Status traps Humidity Trap Temp trapsHumidity traps Temp Trap Configuring Traps SNMP Trap Command Summary To Enable or Disable a Status trapEnabling or Disabling a Status trap To Enable or Disable the Temp trap To Enable or Disable a Load trapSetting the Infeed Load limit To Enable or Disable a Change trap To set the Temperature threshold limits Setting the Temperature sensor threshold limitsTo Enable or Disable the Humid trap Setting the Humidity sensor threshold limits WebServer1 Displaying trap configuration informationTo display trap information Status T ECHNICAL S PECIFICATIONS R ESETTING TO F ACTORY D EFAULTS5. Appendices U PLOADING F IRMWARE To reset to factory defaults using the reset button Resetting to Factory DefaultsTo reset to factory defaults from the HTML interface To reset to factory defaults from the command line Models Europe/Asia Technical SpecificationsPower Ratings Physical Specifications RS-232 port LED IndicatorsData Connections Branch Circuit ProtectionPage