Advanced Operations, Example, Enter | MGE UPS Systems Switched PDU

4. Advanced Operations

Setting the Temperature sensor threshold limits

The Set Trap THS Templow and Set Trap THS Temphigh commands are used to set the lower and upper threshold limits for the Temperature sensor.

To set the Temperature threshold limits:

At the Switched PDU: prompt, type set trap ths, templow or temphigh, followed by the sensor name and a value from 0 to 127 in degrees Celsius. Press Enter.

Example

The following command sets the second temperature high threshold limit to 95:

Switched PDU: set trap ths temphigh .a2 95<Enter>

Enabling or Disabling the Humid trap

The Set Trap THS Humid command is used to enable or disable the Humid trap.

To Enable or Disable the Humid trap:

At the Switched PDU: prompt, type set trap ths humid, followed by the sensor name and on or off. Press

Enter.

Example

The following command enables the Humid trap for the first temperature-humidity sensor:

Switched PDU: set traps ths humid .a1 on<Enter>

Setting the Humidity sensor threshold limits

The Set Trap THS Humidlow and Set Trap THS Humidhigh commands are used to set the lower and upper threshold limits for the Humidity sensor.

To set the Humidity threshold limits:

At the Switched PDU: prompt, type set trap ths, humidlow or humidhigh, followed by the sensor name and a value from 0 to 100 in percent relative humidity. Press Enter.

Example

The following command sets the first humidity sensor low threshold limit to 5:

Switched PDU: set trap ths humidlow .a1 5<Enter>

Page 54 - 301-0399-4 Rev A.

Image 54

MGE UPS Systems Switched PDU Advanced Operations, Setting the Temperature sensor threshold limits, Example, Enter

Contents

Switched PDU Installation and user manual E T N I N U E H T Protective Grounding Terminal InstructionsDangerous Voltage Life-Support Policy GETTING STARTED ContentsINSTALLATION OPERATIONS 1. Getting Started Quick Start Guideuser account prior to attachment to your network 2. Installation Standard AccessoriesAdditional Required Items 1 Power Input 2 Input Current LED 3 Ethernet / RS232 Ports Equipment OverviewFigure 1. Unit Views 4 Temperature / Humidity Ports Figure 2. Retention Bracket assembly Safety PrecautionsInstalling the Power Input Retention Bracket To install the power input retention bracket To connect to the power source Connecting to the Power SourceTo attach a power cord to the unit Mounting Connecting to the Unit Connecting DevicesConnecting the Sensors Serial RS232 portPage HTML I NTERFACE 3. OperationsI NTERFACES C OMMAND L INE I NTERFACE Interfaces Usernames and Passwords3. Operations Outlet Naming and Grouping HTML Interface Figure 4. Example HTML page Logging InTo log in by HTML Group Outlet ControlIndividual Outlet State/Control State Field Values Input Load ConfigurationEnvironmental Monitoring Sensors HTTP/SSL NetworkTelnet/SSH Setting the IP address, subnet mask or gateway Setting SSL access level Serial PortsSetting the HTTP authentication method Setting the data-rate for the serial ports Users OutletsGroups Changing a user password Adding and Deleting group access Changing a user’s access privilege levelAdding and Deleting outlet access Adding and Deleting serial port access Setting the filename for upload SNTPSNMP Testing the FTP upload configuration Restart Command Line InterfaceTools Logging In Operations Command Summary Administrative Command Summary To display the names of commands that you may execute Administrative Command Summary continued To reboot one or more outlets Operations CommandsRebooting outlets Turning outlets on Displaying outlet status To display on/off status of one or more outlets Displaying accessible groups Displaying accessible outletsTo display accessible outlets To display accessible groups Connecting to a serial device Displaying accessible serial portsTo display accessible serial ports Displaying infeed status Starting a new session Displaying the status of the Environmental MonitorTo display the status of the Environmental Monitor To start a new session Creating a user account Administration CommandsUser Administration To create a user account Setting user access level privileges Changing a passwordTo change a password To set the access level privilege for a user Adding outlet access to a user Displaying the access privilege levelsTo display user access privilege levels To grant outlet access to a user Adding group access to a user Deleting outlet access for a userTo delete outlet access for a user To grant group access to a user To display user outlet, group and serial port access Group AdministrationDisplaying user outlet, group and serial port access Creating a group name To add an outlet to a group Outlet AdministrationAdding an outlet to a group Deleting an outlet from a group Displaying outlet information Setting the outlet wakeup stateTo set the wakeup state To display outlet information Enabling or disabling active signal checking for serial connections Serial Port AdministrationSetting the serial ports data-rate To enable or disable active signal checking for serial connections To display system configuration information System AdministrationDisplaying system configuration information Creating a location description Displaying tower information Creating a descriptive tower nameTo create a tower name To display tower information Setting the IP address TCP/IP AdministrationTo perform a warm boot Setting the subnet mask To display network configuration information HTTP AdministrationDisplaying network configuration information To enable or disable HTTP support To set the HTTP authentication method Telnet AdministrationFTP Administration To enable or disable Telnet support Setting the filename to be uploaded Setting the FTP PasswordTo set the FTP password Setting the filepath for the file to be uploaded Displaying SNTP configuration information SNTP AdministrationSetting the SNTP server address To display SNTP configuration information Enabling and Setting up SSH Support Enabling and Setting up SSL SupportSSL Technical Specifications SSH Technical Specifications SSL Technical Specifications SSL Command SummaryEnabling and Setting up SSL Support To enable or disable SSL support SSH Technical Specifications SSH Command SummaryEnabling and Setting up SSH Support To enable or disable SSH support SNMP SNMP Command SummaryEnabling and Setting up SNMP Support To enable SNMP support Setting the Get/Set community strings To reset the trap destinationTo set the trap timer Setting the Trap community string Tower Status traps SNMP TrapsTrap Summary Infeed Status traps Temperature/Humidity Sensor Status traps Outlet Status trapsEnvironmental Monitor Status traps Load traps Temp Trap Temp trapsHumidity traps Humidity Trap Configuring Traps SNMP Trap Command Summary To Enable or Disable a Status trapEnabling or Disabling a Status trap To Enable or Disable a Change trap To Enable or Disable a Load trapSetting the Infeed Load limit To Enable or Disable the Temp trap Setting the Humidity sensor threshold limits Setting the Temperature sensor threshold limitsTo Enable or Disable the Humid trap To set the Temperature threshold limits Status Displaying trap configuration informationTo display trap information WebServer1 U PLOADING F IRMWARE R ESETTING TO F ACTORY D EFAULTS5. Appendices T ECHNICAL S PECIFICATIONS To reset to factory defaults from the command line Resetting to Factory DefaultsTo reset to factory defaults from the HTML interface To reset to factory defaults using the reset button Physical Specifications Technical SpecificationsPower Ratings Models Europe/Asia Branch Circuit Protection LED IndicatorsData Connections RS-232 portPage