Pioneer VSX-AX5i-G manual Speaker Distance, If you want to change a setting before proceeding

Page 44

Setting Up for Surround Sound

Speaker Distance

Adding a slight delay to some speakers is necessary to achieve proper sound depth, separation as well as an effective surround sound effect. You need to figure out the distance from your listening position to your speakers to add the proper delay. The following steps show you how to set the delay time for each channel by specifying the distances from your listening position to each speaker. Once you specify the speaker distances (or it is done automatically in the Easy Setup Guide), the receiver calculates the correct delay times automatically. If continuing from CHANNEL LEVEL go to step 1. If starting fresh, complete steps 1–2 on page 40.

1 The SPEAKER DISTANCE should be selected. If it isn’t use the  buttons to select it. Press the ENTER button.

1-56

The setup possibilities appear on your TV.

2Select each speaker channel with the  buttons and press ENTER.

3Use the  buttons to add or subtract the distance in feet that the speaker is from your normal listening position. Press the ENTER button.

Adjust the speaker distance in 0.1 m increments from 0.1 to 9.0 m.

The default setting is 2.0 m.

1

2

4Repeat steps 2 and 3 for all speaker channels.

5Use the  buttons to select EXIT and press ENTER.

If you want to change a setting before proceeding

start over from step 1.

6Press the SYSTEM SETUP button to leave the SYSTEM SETUP mode.

R

R

L

L

3

44

En

Image 44

Contents Page Installing the Receiver Operating Environment Table of Contents Easy Setup Guide Preparation Surround Setup Basic Expert Link Digital Interface Multichannel Acoustic Calibration EQ System McaccUSB Audio Hook up Audio Scaler HI BIT/HI SamplingChecking the Supplied Accessories Preparing the Remote ControlRemote Control Battery Indicator Loading the batteriesOpening the Front Panel Switching video system between PAL and NtscOperating range of remote control unit Home Theater The Basics Your Home SystemSource Material Listening ModesHooking Up Your DVD Player and TV Digital ConnectionsSpeaker Connections  Speaker terminalsSetting up the Main Unit Assigning the Digital InputsPlace the microphone at your Normal listening position Auto Surround Sound SetupSwitch on the receiver and your TV Check the speaker settings on the OSD Return to normal use Playing a DVD with Surround SoundSelect OK and press Enter Connecting your TV Component Video Input Default SettingsVideo Component videoConnecting Video Components Connecting a DVD playerConnecting VCRs or DVRs Connecting a Video Component to the Front PanelConnecting Satellite TV SAT Components Connecting Analog Audio Components  Audio cordsComponents equipped with 7.1 channel analog output jacks Connecting Digital Audio Components Digital Input Default Settings  Coaxial cords/Optical cables AM loop antenna Connecting the Radio AntennasUsing outdoor antennas Connecting Speakers Speaker impedance Power Connections AC Power Connections AC Outlets European model onlySpeaker placement Placing Your SpeakersWhat is i.LINK? Connecting i.LINK-equipped ComponentsCreating an i.LINK Network Front Panel Display see Mcacc indicator see pages 13 10 i.LINK indicatorEON Mode button see pages Master Volume dialRemote Control Signal SEL button see System Setup buttonCommand button for other components see Listening mode buttons seeVolume +/- buttons Remote Setup buttonTOP MENU/GUIDE button Return buttonDisplay Back Panel AC Outlet European model only switched, 100 W max Component Video Monitor OUT ter- minalsSpeakers terminals see USB Audio terminalSettingDisplays & ControlsUp for Sound Auto SettingSurrback System NormalExit should be selected. Press the Enter button Surround Back SystemEnter button Normal Setup Speaker SettingChannel Level Speaker DistanceSpeaker Setting Front default setting is SmallCenter default setting is Small Surround default setting is SmallIf it isn’t use the  buttons to select It. Press the Enter buttonWith the  buttons choose Speakers that you want to set. PressChannel Level Manual manual test tone modeAuto automatic test tone mode If you want to change a setting before proceeding Speaker DistanceChoose a Listening Mode one of two ways IndicatorStereo and Multichannel Playback Di plays & ControlsSelecting the Input Signal Listening Modes Stereo modesMovie modes Surround mode THX Cinema 2PL II Movie 2PRO Logic II MovieMusic modes Surround mode 2PL II Music 2PRO Logic II MusicAdjusting the Effect of a Listening Mode Adding/Adjusting the Effect in Dolby Pro Logic II Music ModePress Receiver Press the DNR button on the remote control Listening with Acoustic CAL EQDigital Noise Reduction Digital NR Function Press the Acoustic EQ buttonPress the Midnight button on the remote control Listening in Midnight ModeListening in Loudness Mode Adjusting Bass and Treble Listening with Sound DelayListening in Audio Scaler mode Multi Channel In PlaybackSurround Back Channel Mode Press the SB CH Mode button on the remote controlVirtual Surround Back Mode Surround Back Channel ModesPhones jack Dual Mono setting and playbackUsing Headphones Adjusting the Brightness of the Display Dimmer Video SelectAutomatic and Manual Tuning Channel Step Setting multi-voltage model only Direct Access TuningTo cancel before inputting the frequency To Change Channel StepsChoice Memorizing Frequently Used StationsTune in the station you want Press Enter when you have got Naming Memorized StationsEnter the station name you want Characters you want to enterRecalling Memorized Stations Select a class numberChannel you want To step through each channel in orderUsing the RDS display An introduction to RDS European model onlySearching for RDS programs European model only Tune into an FM stationUse the Band button to select the FM band Press the CHARACTER/SEARCH buttonUsing EON European model only Mode you wantPress the Band button to select FM bandPress and hold EON Mode front panel for about two seconds Press the Remote Setup button for three seconds Setting Up the Remote Control to Control Other ComponentsRecalling Settings Stored in the Remote Control Press ENTER. The preset code has been entered Programming Signals from Other Remote Controls Learning Mode Use the  buttons to select Learning and press EnterWhen youre done use the  buttons to select Exit 10Use  to select Exit and pressUsing Remote Control with Other Components CD/MD/CD-R/VCR/DVD/LD/DVD Recorder/Cassette Deck operationsCable TV/Satellite TV/TV operations RETURN/EXITSetting up the Direct Function Use the  buttons to select Dirctfnc and press EnterRecording from Audio/Video Components Speakers B Setup Select Front BI-AMP in the Surrback System setup seeStereo playback in another room Second Zone Bi-amping the front speakers Front BI-AMPOff or cycle through the different Front panel to switch speakers onSpeakers Button Setting up and Using the USB Audio Connection Connecting Additional Amplifiers Pioneer SR System Operating other Pioneer components Press the Remote Setup button for more than three seconds To setup a command select Change and press EnterMulti Operations Use the  buttons to select Multi OPE and press EnterWhen done select Exit and press 10Select Exit and press Enter againPerforming Multi Operations Press the Multi Operation buttonSystem Off Use the  buttons to select Funcname and press Enter Editing Remote Control Display NamesPress the Remote Setup for more than three seconds Press the buttons whose name you want to change Editing Button Names KEY LabelUse the  buttons to select KEY Label and press Enter Adjusting the Light on the Remote Control Press the button you want to clear Clearing Remote Control Settings You Have InputUse the  buttons to select Clear and press Enter Resetting the Main Unit THX Cinema Setup Use the  buttons to select Exit and press ENTER, againFine Tuning Your System Assigning the Component Video Inputs Assigning i.LINK Inputs Components Source you want. Press the EnterIf you want to change the ports for additional i.LINK Function Rename Sacd Setup PHONO/LINE Setup Expert Setup Crossover Network Adjust the level of the channel using the  buttons Fine Channel LevelFine Channel Delay Adjust the distance of each channelUsing the  buttons Subsequent channel. Press Enter100 Acoustic Calibration EQ101 This explanation is for Custom 1 or Custom 102Use the  buttons to select the fre EQ setting by using the  buttons and pressing Enter Use the  buttons to adjust the Trim and press EnterTo use the Data Check feature follow the steps here Bass Peak Level Start or Setting CANCEL. Press104 105 Dynamic Range ControlDolby 106Dolby Digital Dolby Pro LogicDTS 96/24 107DTS Neo6 Link Related Messages 108Troubleshooting Nection, if you change the settings forPower Power does not turn on 109Setup Setup screen doesnt appear 110Overheat blinks in the display and no sound is output Thdct NG blinks111 Other audio problems 112No sound output from one set of speakers Considerable noise in radio broadcastsEven when there is no sound When a search is performedNoise or hum can be heard Being inputUp when using the Signal 114Input/display Display is dark Select buttonMaintenance of External Surfaces Remote control115 Other components cant be operated with the system remotePreset Code Brands 116Brand Tape BrandSpecifications European model 117Specifications multi-voltage model 118119 TNMWF/03E00001 Printed