Pioneer VSX-AX4AVi-S, VSX-AX2AV-S manual Placing the speakers, Bare wire connections

Page 18

03Connecting your equipment

Bare wire connections

Make sure that the speaker cable you’re going to use is properly prepared with about 10 mm of insulator stripped from each wire, and the exposed wire strands twisted together (fig. A).

To connect a terminal, unscrew the terminal a few turns until there is enough space to insert the exposed wire (fig. B). Once the wire is in position, tighten the terminal until the wire is firmly clamped (fig. C).

fig. A

fig. B

fig. C

10mm

Important

•Please refer to the manual that came with your speakers for details on how to connect the other end of the speaker cables to your speakers.

•Other connections on page 46 provides greater detail on alternate speaker setups, such as using speaker system B (page 52), bi-amping (page 53) and bi- wiring (page 53).

•If you are using a THX certified subwoofer use the THX INPUT jack on the subwoofer (if your subwoofer has one) or switch the filter position to THX on your subwoofer.

Placing the speakers

Where you put your speakers in the room has a big effect on the quality of the sound. The following guidelines should help you to get the best sound from your system.

•The subwoofer can be placed on the floor. Ideally, the other speakers should be at about ear-level when you’re listening to them. Putting the speakers on the floor (except the subwoofer), or mounting them very high on a wall is not recommended.

•For the best stereo effect, place the front speakers 2–3m apart, at equal distance from the TV.

•When placing speakers near the TV, we recommend using magnetically shielded speakers to prevent possible interference, such as discoloration of the picture when the TV is switched on. If you do not have magnetically shielded speakers and notice discoloration of the TV picture, move the speakers farther away from the TV.

•If you're using a center speaker, place the front speakers at a wider angle. If not, place them at a narrower angle.

•Place the center speaker above or below the TV so that the sound of the center channel is localized at the TV screen. Also, make sure the center speaker does not cross the line formed by the leading edge of the front left and right speakers.

•It is best to angle the speakers towards the listening position. The angle depends on the size of the room. Use less of an angle for bigger rooms.

•Surround and surround back speakers should be positioned 60 cm–90 cm higher than your ears and titled slight downward. Make sure the speakers don't face each other. For DVD-Audio, the speakers should be more directly behind the listener than for home theater playback.

•Try not to place the surround speakers farther away from the listening position than the front and center speakers. Doing so can weaken the surround sound effect.

•To achieve the best possible surround sound, install your speakers as shown below. Be sure all speakers are installed securely to prevent accidents and improve sound quality.

Front

Center

Front

left

right

 

 

Subwoofer

Surround

 

Surround

left

 

right

Listening position

Surround back left

 

Surround back right

Single surround back speaker

Caution

•Make sure that all speakers are securely installed. This not only improves sound quality, but also reduces the risk of damage or injury resulting from speakers being knocked over or falling in the event of external shocks such as earthquakes.

18

En

Page 17 Page 19
Image 18
Page 17 Page 19
Contents VSX-AX4AVi-S VSX-AX2AV-S Ventilation Caution Operating Environment Contents Controlling the rest of your system Other SettingsUsing other functions Additional informationBefore you start Chapter Installing the receiverBefore you start Checking what’s in the boxMinute guide Chapter Automatically setting up for surround sound McaccMinute guide Introduction to home theater02 5 minute guide EnterMinute guide Better sound using Phase ControlProblems when using the Auto Mcacc Setup Playing a sourceConnecting your equipment Connecting your equipment ChapterRear panel Connecting your equipment When making cable connectionsAbout the video converter Connecting your equipment Connecting your TV and DVD player Or other set-top box Other video sources Use an optical cable for the connectionUse a three-way component video cable Using the component video jacksFor a second recorder, use the DVR/VCR2 outputs DVD playerConnecting your equipment Connecting digital audio sources About the WMA9 Pro decoderSelect these inputs using Input Select remote or Connecting your equipment Connecting analog audio sourcesConnecting a component to the front panel inputs Input Selector dial front panel to selectConnecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersAM loop antenna Connecting antennasTHX speaker system setup Assemble the stand as shown in the illustrationPlugging in the receiver FM wire antennaConnecting external antennas AC outletFront panel Controls and displaysControls and displays Chapter STANDBY/ONOperating range of remote control unit Controls and displaysControls and displays Display Input Select Controls and displays Remote controlReceiver 6TUNE/ST /ENTERShift StatusMultiope SourceAuto playback Listening to your systemListening to your system Chapter Listening in surround soundTHX Games Mode Using the Home THX modesUsing the Advanced surround effects Listening to your systemChoosing the input signal Using Stream DirectSelecting Mcacc presets Listening to your system Listening in stereoUsing surround back channel processing Using the Virtual Surround Back modeSaving station presets Using the tunerUsing the tuner Chapter Listening to the radioListening to station presets Using the tunerNaming station presets An introduction to RDSUsing EON Displaying RDS informationPress Disp for RDS information Making receiver settings from the System Setup menu System Setup menuSystem Setup menu Chapter Select the setting you want to adjustSystem Setup menu MemorySurround back speaker setting If necessary, confirm the speaker configuration in the OSD.1Manual Mcacc setup Fine Channel LevelFine Speaker Distance Adjust the level of the left channelWhen youre finished, press Return Standing WaveSelect the channels you want and adjust to your liking Select ‘Standing Wave’ from the Manual Mcacc setup menuSelect ‘EQ Adjust’ from the Manual Mcacc setup menu Acoustic Calibration EQHow to use Professional Acoustic Calibration EQ How to interpret the graphical outputUsing Professional Acoustic Calibration EQ Select ‘EQ Professional’ then press EnterSelect an option and press Enter Checking Mcacc preset data Copying Mcacc preset dataData Management Renaming Mcacc presets Manual speaker setupSpeaker Setting Clearing Mcacc presetsSelect a setup option Select ‘Speaker Setting’ from the Manual SP Setup menuSelect ‘Channel Level’ from the Manual SP Setup menu Confirm your selected setup optionSpeaker Distance Bass Peak LevelEnter THX Audio Setting CurveOther connections Connecting an iPodConnecting your iPod to the receiver Other connections ChapterBasic playback controls Connecting using HdmiOther connections Button What it doesUsing the i.LINK interface About HdmiOn a HDMI-compatible monitor.1 About i.LINK Checking the i.LINK inputsAbout Pqls rate control Creating an i.LINK networkSelecting the multichannel analog inputs Using the USB interfaceConnecting the multichannel analog inputs Use standard RCA/phono jack cables for the connectionsUse the Input Select button to select USB Second Zone speaker B setupSwitching the speaker system Start playback of a source on your computerBi-wiring your speakers Bi-amping your front speakersConnect your speakers as shown below Other connections Connecting additional amplifiers Multi-room listeningMaking multi-room connections Basic multi-room setup Room Multi-room listening optionsSub room Input sources available Multi-room remote controls Connecting an IR receiverUsing the multi-room controls InputUsing this receiver with a Pioneer plasma display Switching components on and off using the 12 volt triggerPioneer plasma display Display Using the SR+ mode with a Pioneer plasma displayPioneer plasma DVD player Satellite receiver, etcOther connections Connecting a PC for Advanced Mcacc output Advanced Mcacc output using your PCOther Settings Other Settings ChapterInput Setup menu Input function default and possible settings Other SettingsOther Setup menu Select ‘Other Setup’ then press EnterMulti-Room and IR receiver setup OSD AdjustmentSR+ Setup for Pioneer plasma displays Setting the AV options Using other functionsUsing other functions Chapter Setting What it does OptionsMaking an audio or a video recording Using other functionsPlaying a different source when recording Recout SourceChecking your system settings Switching the speaker impedanceUsing the sleep timer Dimming the displayDisplay shows RESET? Resetting the systemDefault system settings Setting DefaultProgramming signals from other remote controls Setting the remote to control other componentsSelecting preset codes directly Controlling the rest of your systemConfirming preset codes Erasing one of the remote control button settingsResetting the remote control presets Controlling the rest of your systemMulti Operation and System Off Renaming input source namesDirect function Programming a multi-operation or a shutdown sequenceUsing multi operations Using System offButtons Function Components Controlling the rest of your system Controls for TVsControls for other components Function ComponentsOperating other Pioneer components with this unit’s sensor Button s Function ComponentsDecide which component you want to use the remote sensor Additional information TroubleshootingPower Additional information ChapterOther audio problems Additional informationSettings VideoDisplay Professional Calibration EQ graphical outputRemote control Link interfaceLink messages USB interfaceMessage Explanation Symptom Cause Action IPod messagesAdditional information Surround sound formats DolbyWindows Media Audio 9 Professional About THX THX Games Mode Listening modes with different input signal formatsStereo 2 channel signal formats THX MusicModeMultichannel signal formats Input signal format StandardAuto Surround Input signal format Surround Back speakersUnavailable with only one surround back speaker connected Additional information Specifications Cleaning the unitFeatures Our philosophyAdditional information Pioneer Corporation 05F00001 Printed ARB7335-E
Top Page Image Contents