Extron electronic DMP 44 LC manual Power Supply Wiring

Page 12

2-Pole Captive Screw

Connector

Tie Wrap

 

SECTION A–A

 

3/16”

 

(5 mm) Max.

Smooth

 

 

Ridges

A

A

Power Supply

Output Cord

Figure 2. Power Supply Wiring

WARNING: The two power cord wires must be kept separate while the power supply is plugged in. Remove power before wiring.

CAUTIONS: • Always use a power supply supplied by or specified by Extron. Use of an unauthorized power supply voids all regulatory compliance certification and may cause damage to the supply and the end product.

Unless otherwise stated, the AC/DC adapters are not suitable for use in air handling spaces or in wall cavities. The power supply is to be located within the same vicinity as the Extron AV processing equipment in an ordinary location,

Pollution Degree 2, secured to the equipment rack within the dedicated closet, podium or desk.

The installation must always be in accordance with the applicable provisions of National Electrical Code ANSI/NFPA 70, article 75 and the Canadian Electrical

Code part 1, section 16. The power supply shall not be permanently fixed to building structure or similar structure.

CAUTION: When connecting the power supply, voltage polarity is extremely important. Applying power with incorrect voltage polarity could damage the power supply and the DMP 44 LC. Identify the power cord negative (ground) lead by the ridges on the side of the cord or a black heat shrink wrapping around it.

CAUTION: The length of the exposed (stripped) copper wires is important. The ideal length is 3/16 in (5 mm). Longer bare wires can short together. Shorter wires are not as secure in the direct insertion connectors and could be pulled out.

Do not tin the stripped power supply leads. Tinned wires are not as secure in the captive screw connectors and could be pulled out.

NOTE: To verify the polarity before connection, check the no load power supply output with a voltmeter.

Use the supplied tie-wrap to strap the power cord to the extended tail of the connector.

NOTE: To avoid losing adjustments when configuring the DMP 44 LC via

 

SIS commands issue a 2FF or if using the DSP Configurator, select

 

Tools > Save Changes to Device to store the latest changes to the

 

device. Wait several minutes after saving the adjustments before disconnecting

 

power.

 

DMP 44 LC • Installation

6

Image 12
Contents DMP 44 LC Safety Instructions English FCC Class a Notice Conventions Used in this Guide Contents DMP 44 LC Contents Features About This GuideAbout the DMP 44 LC Digital Matrix Processor DMP 44 LC Introduction DMP 44 LC Introduction DMP 44 LC Application Diagram MLS 102 VGARear Panel Features and Cabling Mounting the DMP 44 LCPower Supply Wiring Audio Input Wiring USB Configuration port front panel Operation DMP 44 LC OperationPower Cycle Front Panel OperationRear Panel Operation Firmware Updates Reset Actuator and LED Hardware Reset ModesDefault reset state of the device is Digital Input Ports DMP 44 LC Operation DSP Processing and Signal Flow Line Input Signal ChainMix Matrix Line Output ChainProcessor Blocks Line Input Channels Line Input GainFilter Block Filter Block Dialog BoxFilter Dialog Box, Filters Added Parametric Equalizer Parametric Filter Dialog Box, 1000 HzHigh Pass Low PassSetting bass and treble filters Bass and Treble ShelvingConfiguring Groups Treble Groups Configuring Bass and Treble Groups DMP 44 LC Operation DMP 44 LC Operation Dynamics Processor CompressorDMP 44 LC Operation Limiter DuckingDucker Configuration Dialog Ducking Configuration Dialog Current source indicatorDucker Configuration, Input Priority PriorityMix Matrix Mix Matrix Outlined in RedMix-point GUI behavior DMP 44 LC Operation Input 1 to Output Line Output Channels FilterVolume DynamicsConnection Options RS-232 PortDMP 44 LC RS-232 protocol USB port detailsUsing the Command/Response Tables USB Port front panelDMP 44 LC-initiated Messages Command/Response Table Overview Command/Response Table for Basic SIS CommandsError Responses Symbol definitionsCommand/Response Table for Basic DMP 44 LC SIS Commands General commandsCommand Ascii Command Response Additional Description Special CharactersSetup Commands ZAP Commands Factory Defaults and RAM CommandsName commands Bidirectional Serial Data PortGroup Master Commands Group Master NameSet Master Value Set GroupDigital Input Commands Digital Input Command TableCommand/Response Tables for DSP SIS Commands DSP Processors Addressable via SIS CommandsCommand/Response Tables for Audio SIS Commands See . Level Control and Mix-point Selection TablesCommand/Response Table for DMP 44 LC DSP SIS commands Audio level control, and mix-point selectionAudio mute Audio group master commands ED X6%*X6GRPMLevel Control and Mix-point Selection Tables Installing the DSP Configurator Program Software ControlDVD Software Menu Install the USB Driver USB Installer Splash ScreenDSP Configurator Program Starting the ProgramUsing the Program Emulate Mode vs. Live Mode Synchronizing Pull vs. PushSelecting Live Mode and Pushing or Pulling a Configuration Selecting Live ModeSelecting Live Mode Presets Previewing/Recalling a Preset Behavior for previewing and applying presets is as followsBuilding a Preset Save PresetManaging Presets in the GUI Save PresetPresets Pull vs. Push or Create Live Push Configuration Advanced, Push Presets, All AdvancedSelected Push Configuration Advanced, Push Presets, Selected To switch from emulate mode to live modeSpecifications AudioAudio input Audio processingControl/remote audio processor Control digital input portsGeneral Part Numbers and Accessories AccessoriesMounting Included PartsUL Rack Mounting Guidelines Rack MountingFurniture Mounting MBU 123, Under-Desk MountingFirmware Loader Select Tools, then Firmware LoaderDMP 44 LC Reference Information DMP 44 LC Hardware Reset Modes DMP 44 LC Reset Mode SummaryUSA, Canada, South America Japan Central America Europe, Africa, and the Middle China EastAsia Middle East Europe
Related manuals
Manual 2 pages 6.16 Kb

DMP 44 LC specifications

The Extron DMP 44 LC is a powerful digital audio processor designed to cater to a wide range of audio distribution and mixing applications. It combines advanced audio processing capabilities with intuitive controls, making it an ideal solution for classrooms, conference rooms, and other professional audio environments. The DMP 44 LC features four inputs and four outputs, which provide incredible flexibility for any audio setup.

One of the standout features of the DMP 44 LC is its comprehensive DSP capabilities. The device incorporates Extron's renowned DSP technology, which offers extensive signal processing functionality including automatic mixing, gain sharing, EQ, delay, and filtering. These tools allow users to optimize audio performance, ensuring that sound quality is consistent and clear across all speakers and microphones.

In terms of connectivity, the DMP 44 LC offers a versatile array of input and output options. It includes balanced, low-impedance microphone and line level inputs, ensuring compatibility with a wide variety of audio sources. Outputs are also balanced, allowing for seamless integration with professional audio systems. The unit’s input and output configuration can be easily customized, accommodating different audio formats and setups.

The DMP 44 LC utilizes Extron’s patented ProDSP technology, which delivers precise signal processing capabilities without sacrificing audio quality. This technology supports high-resolution audio processing, enabling users to achieve the best sound reproduction possible. Moreover, the device allows for remote control and monitoring via an intuitive web-based interface, making it easy to manage audio settings from any location.

Another key characteristic of the DMP 44 LC is its robust design tailored for professional use. The compact form factor can be easily integrated into various environments, whether mounted in a rack or placed on a shelf. Additionally, its enhanced thermal management and sturdy construction ensure reliability and durability in demanding applications.

The DMP 44 LC embodies the latest advancements in audio technology, making it a reliable choice for professionals seeking high-quality sound management. With its extensive features, the digital audio processor allows for seamless audio mixing and processing, ensuring optimal performance in any audiovisual setup.