Controlling the rest of your system | 12 |
6If necessary, press the input source button for the component whose command you want to input.
This is only necessary if the command is for a new component (input source).
7Select the button for the command you want to input.
The following remote control commands can be selected:
RECEIVER | INPUT |
| SYSTEM OFF |
|
|
|
|
|
| SOURCE |
|
|
|
|
| ||
| SELECT |
|
|
|
|
|
|
|
|
|
|
|
|
| TV CONTROL |
| |
|
|
|
| TVVOL |
| INPUT | TVCH | VOL |
USB |
| DVR 2 |
|
|
| SELECT |
|
|
|
|
|
|
|
|
| ||
DVD | TV | DVR 1 | TVCTRL |
|
|
|
|
|
HDMI 2 | CD |
|
| A | REC |
|
| |
iPod | HDMI 1 | TUNER | RECEIVER |
|
|
| MUTE | |
|
|
|
| |||||
|
|
|
| MPX | B | EON | REC STOP | JUKEBOX |
| SLEEP | S.RETRIEVER | ANALOG |
| C | D | E | |
|
|
| ATT |
|
|
|
|
|
| SR+ | DIMMER | MIDNIGHT/ | AUDIO | SUBTITLE | HDD | DVD | |
| DISP |
|
| CH | CH | |||
|
|
| LOUDNESS |
|
| |||
|
|
|
|
|
| PHOTO | STEREO/ | |
|
|
|
| STATUS |
| SIGNAL SEL | SBch | |
| DIALOG E |
|
|
| F.S.SURR | |||
|
|
|
|
|
|
| ||
D.ACCESS +10 |
| CLASS DISC | MULTI OPE |
| THX | STANDARD | ADV.SURR | |
|
|
| ENTER |
|
|
|
|
|
AVPARAMETER |
| CHLEVEL | SHIFT |
| PHASE | MCACC | S.DIRECT | |
TOPMENU |
|
| MENU |
|
|
|
|
|
| TUNE |
|
|
|
|
|
|
|
| ST | ST | T.EDIT |
|
|
|
|
|
SETUP | ENTER | RETURN |
|
|
|
|
| |
|
|
|
|
|
|
| ||
GUIDE PTYSEARCH TUNE |
|
|
|
| RECEIVER |
| ||
BAND |
|
|
|
|
|
•You don’t need to program the receiver to switch on or off. This is done automatically.
With Pioneer components, you don’t need to:
•program the power to switch off in a shutdown sequence (except DVD recorders);
•program the power to switch on if it’s the source component selected in step 3;
•program a Pioneer TV or monitor to switch on if the input function (selected in step 2) has video input terminals;
These take priority in multi operations (not shutdown).
8Repeat steps
9When you’re finished, use / to select EDITEXIT from the menu and press ENTER.
You will return to the remote control SETUP menu. Select * EXIT * again to exit.
Using multi operations
You can start multi operations with the receiver switched on, or in standby.
AUDIO | SUBTITLE | HDD | DVD | |
DISP |
| CH | CH | |
| PHOTO | STEREO/ | ||
STATUS | SIGNAL SEL | SBch | ||
F.S.SURR | ||||
MULTI OPE | THX | STANDARD | ADV.SURR |
SHIFT PHASE MCACC S.DIRECT
RECEIVER
1 Press MULTI OPE.
MULTI OP flashes in the display.
2Press an input source button that has been set up with a multi operation.
The receiver switches on (if it was in standby) and the programmed multi operation is performed automatically.
Using System off
|
|
| AUDIO | SUBTITLE | HDD | DVD |
|
| SYSTEM OFF | DISP |
| CH | CH |
RECEIVER | INPUT |
| PHOTO |
| ||
SOURCE | STATUS | SIGNAL SEL | SBch | STEREO/ | ||
| SELECT |
| F.S.SURR | |||
|
|
| MULTI OPE | THX | STANDARD | ADV.SURR |
|
|
| SHIFT | PHASE | MCACC | S.DIRECT |
USB |
| DVR 2 |
| RECEIVER |
| |
DVD | TV | DVR 1 TVCTRL |
|
| ||
|
|
|
|
1 Press MULTI OPE.
MULTI OP flashes in the display.
2 Press SOURCE.
The command sequence you programmed will run, then
all Pioneer components will switch off1, followed by this receiver.
Note
1 In order to avoid accidently switching off a DVD recorder that is currently recording, no DVD recorder power off codes are sent.
65
En