Pioneer VSX-LX50 manual Video, Settings

Page 70

13Additional information

Symptom

Remedy

Can’t record audio.

• You can only make a digital recording from a digital source, and an analog recording from an analog

 

source.

 

• For digital sources, make sure that what you’re recording isn’t copy protected.

 

• Check that the OUT jacks are properly connected to the recorders input jacks (see Connecting analog

 

audio sources on page 16).

 

 

Subwoofer output is very low.

• To route more signal to the subwoofer, set it to PLUS or set the front speakers to SMALL (see Speaker

 

Setting on page 46).

 

 

Everything seems to be set up

• The speakers may be out of phase. Check that the positive/negative speaker terminals on the receiver are

correctly, but the playback sound

matched with the corresponding terminals on the speakers (see Connecting the speakers on page 17).

is odd.

 

 

 

The PHASE CONTROL feature

• If applicable, check that the lowpass filter switch on your subwoofer is off, or the lowpass cutoff is set to

doesn’t seem to have an audible

the highest frequency setting. If there is a PHASE setting on your subwoofer, set it to 0º (or depending on

effect.

the subwoofer, the setting where you think it has the best overall effect on the sound).

 

• Make sure the speaker distance setting is correct for all speakers (see Speaker Distance on page 48).

 

 

Noise or hum can be heard even

• Check that personal computers or other digital components connected to the same power source are not

when there is no sound being

causing interference.

input.

 

 

 

There seems to be a time lag

• See Automatically setting up for surround sound (Auto MCACC) on page 8 to set up your system again

between the speakers and the

using MCACC (this will automatically compensate for a delay in the subwoofer output).

output of the subwoofer.

 

 

 

The maximum volume available

• This is not a malfunction. If the levels in Channel Level on page 47 have been adjusted, the maximum

(shown in the front panel display)

volume will change accordingly.

is lower than the +12dB

 

maximum.

 

 

 

Video

Symptom

Remedy

No image is output when an input

• Check the video connections of the source component (see page 14).

is selected.

• For high-definition video (using component video connections), or when digital video conversion is

 

switched off (in Setting the AV options on page 58), you must connect your TV to this receiver using the same

 

type of video cable as you used to connect your video component.

 

• Make sure the input assignment is correct for components connected using component or HDMI cables

 

(see The Input Setup menu on page 56).

 

• Check the video output settings of the source component.

 

• Check that the video input you selected on your TV is correct.

 

 

Can’t record video.

• Check that the source is not copy-protected.

 

• The video converter is not available when making recordings. Check that the same type of video cable is

 

used for connecting both the recorder and the video source (the one you want to record) to this receiver.

 

 

Noisy, intermittent, or distorted

• Sometimes a video deck may output a noisy video signal (during scanning, for example), or the video

picture.

quality may just be poor (with some video game units, for example). The picture quality may also depend on

 

the settings, etc. of your display device. Switch off the video converter and reconnect the source and display

 

device using the same type of connection (component, S-video or composite), then start playback again.

 

 

Settings

Symptom

Remedy

The Auto MCACC Setup

• The ambient noise level may be too high. Keep the noise level in the room as low as possible (see also

continually shows an error.

Problems when using the Auto MCACC Setup on page 10). If the noise level cannot be kept low enough, you

 

will have to set up the surround sound manually (page 40).

 

 

After using the Auto MCACC

• There may have been some low frequency noise in the room from an air-conditioner, motor, etc. Switch

Setup, the speaker size setting is

off all other appliances in the room and use Auto MCACC Setup again.

incorrect.

• Depending on a number of factors (room size, speaker placement, etc.) this may occur in some cases.

 

You can change the speaker setting manually in Speaker Setting on page 46, and use the ALL (Keep

 

SPsetting) option for the Auto Mode in Automatic MCACC (Expert) on page 37 if this is a recurring problem.

 

 

70

En

Image 70
Contents VSX-LX50 Important the Moulded Plug Risk of Electric Shock Do not OpenOperating Environment Contents Using other functions System Setup menu Controlling the rest of your systemOther Settings Other connectionsBefore you start FeaturesBefore you start Chapter Before you start Installing the receiverEasy-to-use LCD remote control Checking what’s in the box02 5 minute guide Chapter Automatically setting up for surround sound Auto McaccMinute guide Introduction to home theaterMinute guide 02 5 minute guide Better sound using Phase ControlProblems when using the Auto Mcacc Setup Playing a sourceConnecting your equipment Chapter Connecting your equipmentRear panel When making cable connections Connecting your equipmentAbout the video converter Connect using a standard video cable or an S-video cable Connecting your equipment Connecting your TV and DVD playerConnecting a satellite/cable receiver or other set-top box 342Using the component video jacks Connecting a DVD/HDD recorder, VCR and other video sourcesDVR, VCR, etc Connecting digital audio sources Use a three-way component video cableConnect using a stereo RCA/phono jack audio cable Connecting analog audio sourcesConnecting a component to the front panel inputs About the WMA9 Pro decoderConnecting your equipment Installing your speaker system Connecting the speakersBare wire connections Placing the speakersConnecting antennas THX speaker system setupPlug the power cord into a power outlet Connecting external antennasPlugging in the receiver Controls and displays Chapter Controls and displaysFront panel Operating range of remote control unit Controls and displaysSound Phase ControlRtrv Stream DirectInput Select Controls and displays Remote controlRECEIVER SelectShift StatusMulti OPE SOURCEAuto playback Listening in surround sound Listening to your systemListening to your system Chapter Standard surround soundTHX Games Mode Using the Home THX modesUsing the Advanced surround effects Listening to your systemListening in stereo Using Front Stage Surround AdvanceUsing Stream Direct Stereo See Listening in stereo above for more on thisUsing surround back channel processing Listening to your system Selecting Mcacc presetsChoosing the input signal While listening to a source, press McaccUsing the Virtual Surround Back mode Using the tone controls Listening to your system Using Midnight and LoudnessUsing the Sound Retriever Press Tone to select the frequency you want to adjustUSB playback Chapter Using the USB interfaceUSB playback Basic playback controlsUSB playback Compressed audio compatibilitySaving station presets Using the tunerUsing the tuner Chapter Listening to the radioListening to station presets Using the tunerNaming station presets An introduction to RDSDisplaying RDS information Using EONPress Disp for RDS information Making receiver settings from the System Setup menu System Setup menuSystem Setup menu Chapter Select the setting you want to adjustSystem Setup menu PointSurround back speaker setting Default setting Normal SBManual Mcacc setup Fine Channel LevelSelect ‘Fine SP Distance’ from the Manual Mcacc setup menu Select ‘Fine Ch Level’ from the Manual Mcacc setup menuAdjust the level of the left channel When youre finished, press ReturnSelect the channels you want and adjust to your liking Select ‘Standing Wave’ from the Manual Mcacc setup menuSelect ‘EQ Adjust’ from the Manual Mcacc setup menu Standing WaveHow to interpret the graphical output How to use Professional Acoustic Calibration EQProfessional Acoustic Calibration EQ Select ‘EQ Professional’ then press Enter Using Professional Acoustic Calibration EQSelect an option and press Enter Checking Mcacc preset data System Setup menu Data ManagementCopying Mcacc preset data Select ‘Data Management’ from the System Setup menuRenaming Mcacc presets Manual speaker setupSpeaker Setting Clearing Mcacc presetsConfirm your selected setup option Select ‘Channel Level’ from the Manual SP Setup menuSelect a setup option Adjust the level of each channel using the / ButtonsSpeaker Distance THX Audio SettingCurve Other connections Connecting an iPodConnecting your iPod to the receiver Other connections ChapterBasic playback controls Watching photos and video contentOther connections Use / to move to previous/next levelsAbout Hdmi Other connections Connecting using HdmiYou can also use the front panel controls Switching the speaker system Connecting the multichannel analog inputsSpeaker B setup Selecting the multichannel analog inputsBi-amping your front speakers Bi-wiring your speakersConnect your speakers as shown below Using this receiver with a Pioneer plasma display Other connections Connecting additional amplifiersLarge Display Using the SR+ mode with a Pioneer plasma displayPioneer plasma DVD player Satellite receiver, etcInput Setup menu Other SettingsOther Settings Chapter Input function default and possible settingsSR+ Setup for Pioneer plasma displays Other SettingsOther Setup menu OSD AdjustmentSetting the AV options Using other functionsUsing other functions Chapter Setting What it does OptionsSelect the source you want to record Using other functionsMaking an audio or a video recording Prepare the recorderChecking your system settings Using the sleep timerSwitching the speaker impedance Press Status to check the system settingsPress System Setup to confirm Using other functions Resetting the systemDefault system settings Setting DefaultProgramming signals from other remote controls Setting the remote to control other componentsSelecting preset codes directly Controlling the rest of your systemConfirming preset codes Erasing one of the remote control button settingsResetting the remote control presets Controlling the rest of your systemDirect function Renaming input source namesMulti Operation and System Off Programming a multi-operation or a shutdown sequenceSelect the button for the command you want to input Using multi operationsUsing System off Press Multi OPEControls for other components Controlling the rest of your system Controls for TVsButtons Function Components Operating other Pioneer components with this unit’s sensor Decide which component you want to use the remote sensorAdditional information TroubleshootingPower Additional information ChapterSymptomRemedy Other audio problemsAdditional information Settings VideoDisplay 96 kHzSymptom Remote controlUSB interface IPod messages Symptom Cause ActionThere is a problem with the signal path from Noisy or distorted pictureAdditional information Surround sound formats DolbyAbout THX Windows MediaTM Audio 9 ProfessionalRe-Equalization THX Select2 Cinema modeTHX Games Mode Timbre MatchingInput signal format Standard Stereo 2 channel signal formatsAuto Surround Multichannel signal formats Channel decoding used for all sourcesChannel Dolby Digital Plus Straight decodingDecoding Surround Back speakers Input signal format Additional information Specifications Cleaning the unitPioneer Corporation