Pioneer 516-S/-K, VSX-416-S/-K Additional information Resetting the main unit, Power cord caution

11Additional information

Resetting the main unit

Use this procedure to reset all the receiver’s settings to the factory default. Use the front panel controls to do this.

1Switch the receiver into standby.

2While holding down the TONE button,

press and hold the STANDBY/ON button for about three seconds.

3When you see RESET? appear in the display, press the ENTER button.

OK? shows in the display.

4Press SETUP to confirm.

OK appears in the display to indicate that the receiver has been reset to the factory default settings.

Switching the speaker impedance

We recommend using speakers of 8 Ω with this system, but it is possible to switch the imped- ance setting if you plan to use speakers with a 6 Ω impedance rating.

•With the receiver in standby, press the SPEAKER IMPEDANCE button.

Each time you do this, you switch between the impedance settings:

•SP 6 OHM – Use this setting if your speakers are rated at 6 Ω.

•SP 8 OHM – Use this setting if your speakers are rated at 8 Ω or more.

Power cord caution

Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or an electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it

46

with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest Pioneer authorized service center or your dealer for a replacement

Specifications

Amplifier section

•Continuous power output (stereo)

Front . . . . . . . 100 W (DIN 1 kHz, THD 1.0 %, 8 Ω)

•Power output (surround)

Front

. . . . . 100 W per channel (1 kHz, THD 1.0 %, 8 Ω)

Center . . . . . . . . . . 100 W (1 kHz, THD 1.0 %, 8 Ω) Surround. . . . . . . . . . . . . . . . . .100 W per channel (1 kHz, THD 1.0 %, 8 Ω)

Surround Back (VSX-516 model only)

. . . . . 100 W per channel (1 kHz, THD 1.0 %, 8 Ω)

Audio section

•Input (Sensitivity/Impedance)

CD, DVR/VCR, CD-R/TAPE/MD,

DVD/LD, TV/SAT. . . . . . . . . . . . . . . .200 mV/47 kΩ

•Frequency response

CD, DVR/VCR, CD-R/TAPE/MD, DVD/LD,

TV/SAT. . . . . . . . . . . . . . . 5 Hz to 100 000 Hz dB

•Output (Level/Impedance)

DVR/VCR REC, CD-R/TAPE/

MD REC . . . . . . . . . . . . . . . . . . . . . 200 mV/2.2 kΩ

•Tone control

Bass . . . . . . . . . . . . . . . . . . . . . . . ± 6 dB (100 Hz) Treble . . . . . . . . . . . . . . . . . . . . . . ± 6 dB (10 kHz) Loudness . . . . . . +10 dB/+5 dB (100 Hz/10 kHz)

(at volume level –50 dB)

•Signal-to-Noise Ratio DIN (Continuous rated power output / 50mW)

CD, DVR/VCR, CD-R/TAPE/MD,

DVD/LD, TV/SAT. . . . . . . . . . . . . . . . . 88 dB/64 dB

En