Pioneer VSX-915-S/-K, VSX-815-S/-K manual Connecting the speakers on, VSX-815/915 only The SR

Page 80

14Additional information

Problem

Remedy

No sound is output or a noise

• Set the digital volume level of the player to full, or to the neutral

is output when software with

position.

DTS is played back.

• Make sure the player's settings are correct and/or the DTS signal out

 

is on. Refer to the instruction manual supplied with the DVD player.

 

• Set the input signal type to DIGITAL (see Choosing the input signal

 

on page 40)

 

 

When a search is performed

• This is not a malfunction, but be sure to turn the volume down to

by a DTS compatible CD

prevent the output of loud noise from your speakers.

player during playback, noise

 

is output.

 

 

 

Everything seems to be set up

• Check that the positive/negative speaker terminals on the receiver

correctly, but the playback

are matched with the corresponding terminals on the speakers (see

sound is odd.

Connecting the speakers on page 22).

 

 

There seems to be a time lag

• See Automatically setting up for surround sound (MCACC) on page 11

between the speakers and the

to set up your system again using MCACC (this will automatically

output of the subwoofer.

compensate for a delay in the subwoofer output).

 

 

After using the Auto MCACC

• Low-frequency noise could have been caused by an air conditioner or

Setup, the speaker size

motor. Switch off all appliances in the room and rerun the Auto

setting (LARGE or SMALL) is

MCACC Setup.

incorrect.

 

 

 

Can’t operate the remote

• Replace the batteries (refer to page 5).

control.

• Operate within 7 m, 30° of the remote sensor on the front panel (refer

 

to page 35).

 

• Remove the obstacle or operate from another position.

 

• Avoid exposing the remote sensor on the front panel to direct light.

 

• VSX-815/915 only – Unplug anything connected to the CONTROL IN

 

jack and use remote normally (see Operating other Pioneer components

 

on page 25).

 

 

The display is dark or off.

• Press FL DIMMER on the remote control repeatedly to return to the

 

default.

 

 

VSX-815/915 only – The SR

• Reinsert the SR cable, making sure it’s connected to the right jack

cable is connected, but the

(see Operating other Pioneer components on page 25).

connected components can’t

• Make sure an analog connection has been made between the units.

be operated with the remote.

• This feature only works with Pioneer products.

 

 

80

En

Page 79 Page 81
Image 80
Page 79 Page 81
Contents VSX-515-S/-KVSX-815-S/-KVSX-915-S/-K Voltage selector Risk of Electric Shock Do not OpenContents Other Settings Controlling the rest of your system VSX-515Controlling the rest of your system VSX-815/915 Other connectionsBefore you start Before you start ChapterIntroduction to home theater Loading the batteriesInstalling the receiver Before you startVentilation Illustration shows the VSX-815/915 modelMinute guide Minute guide ChapterListening to Surround Sound Hook up your DVD playerThis receiver Powered 02 5 minute guideConnect your speakers Surround speakersFor more on this.3 Play a DVD, and adjust the volume to your likingMinute guide 0ch 3.0ch 0ch4.0ch 0ch 5.0ch 02 5 minute guide Using the Quick Setup1ch Quick surround sound setup Quick surround sound setup ChapterAbove VSX-515 left and VSX-815/915 right Illustration shows the VSX-915 modelQuick surround sound setup Following options then cursor up/down to check the settingsSelect Check OK in the display then press EnterOther problems when using the Auto Mcacc Setup Making cable connections Connecting upConnecting up Chapter Connecting up Video cablesComponent video cables VSX-815/915 model onlyConnecting up Connecting a DVD player and TV Illustration shows the VSX-915, butUse an optical cable for the connection.4 This receiver Connecting the multichannel analog outputsAudio and Video inputs on this receiver.2 Connecting other audio components About the WMA9 Pro decoderConnecting other video components This receiverUsing the component video jacks Connecting to the front panel video terminalIf you connect any source component to Comp 1 DVD Comp 2 TV Comp 3 DVRConnecting up Connecting antennas Using external antennasFM wire antenna AM loop antennaConnecting up Connecting the speakers VSX-815 model only Hints on speaker placementB speaker systems Overhead view of speaker setup View of 7.1 channel speaker setupConnecting up Operating other Pioneer components Pioneer productsControls and displays Controls and displays ChapterFront panel STANDBY/ONControls and displays Controls and displays Display Remote control VSX-815/915 MidnightLoudness ReceiverAccess SR+TOP Menu DTV MenuDTV ON/OFF DTV InfoTuner Display MPXSetup PresetReset EFFECT/CH SELControls and displays Remote control VSX-515 STEREO/DIRECTMaster Volume + System Setup and Component control buttonsOperating range of remote control unit Volume +Display Channel +Listening to your system Listening to your system ChapterAuto playback Listening in surround soundSee which you like.2 Using the Advanced surround effectsListening to your system Dolby Pro Logic IIx Music settings Neo6 Music settingsUse the +/- buttons to adjust the setting Press EFFECT/CH SEL again to adjust other settingsImage Listening in stereoListening with Acoustic Calibration EQ Listening to your system Choosing the input signal Extended mode Using the surround back channelPress Extended Mode front panel to Select a surround back channel optionSwitched off VSB OFF.1Using the tone controls Press Tone to select the frequency you want to adjustPress Dialog E to switch dialog enhancement on or off Enhancing dialogVSX-815/915 model Listening to your system Playing other sourcesVSX-515 model Listening to your system Using the sleep timer 30 minOff Press Sleep repeatedly to set the sleep timeSystem Setup menu System Setup menu ChapterSurround back speaker setting Press Return to confirm and exit the current menuSystem Setup menu Manual Mcacc speaker setupFine Channel Level Fine Channel DistanceAcoustic Calibration EQ Setting the Acoustic Calibration EQ automaticallySettings Copying your Acoustic Calibration EQ Setting the Acoustic Calibration EQ manually Checking your Acoustic Calibration EQ settingsChannel you want, using Right to check the settingsSystem Setup menu Manual speaker setup Speaker settingWhen you’re finished, press Return Default setting 100HzCrossover network Channel levelConfirm your selected setup option When you’re finished, press Return TipSelect ‘SP DISTN.’ from the SP Setup menu Speaker DistanceUsing the tuner Using the tuner ChapterTuning directly to a station Listening to the radioUsing the tuner Saving station presetsDisplay shows ST. MEMORY, then a blinking memory class Press EnterChanging the frequency step Naming station presetsListening to station presets Making recordings Making recordings ChapterMaking an audio or a video recording Source as for the recorder.1Setting the remote to control other components Selecting preset codes directlyControlling the rest of your system Controlling the rest of your system ChapterClearing all the remote control settings Controlling the rest of your system Direct functionVolume Controlling the rest of your system Controls for TVsInput Select ChannelDisc Controlling the rest of your systemControls for other components Enter Guide Controlling the rest of your system Preset Code List On digital STBDVD Recorder Manufacturer CodeRemote LCD display shows Setup Use Cursor left/right to select Preset then press EnterLCD display shows OK.2 Programming signals from other remote controlsUse cursor left/right to select Learn then press Enter Erasing all of the remote control presets Press the Receiver button to exit and store the operationsUse cursor left/right to select Erase then press Enter Press and hold the button to be erased for two secondsConfirming preset codes Use cursor left/right to select Direct F then press EnterSelect Button must be pressed twice to take effect Cassette deck Stops playback on some models, pressing this whenSHIFT+ + CH+ HDD Shift+ CH Second Zone speaker B setup Switching the speaker systemOther connections Other connections ChapterBi-wiring your speakers Select the SB Biamp setting from the ‘SB. SYSTEM’ menuOther connections Bi-amping your front speakersOther connections Connecting additional amplifiers Pioneer plasma displayUsing the SR+ mode with a Pioneer plasma display Pioneer plasmaDisplay DVD player Satellite receiver, etcOther Settings Other Settings ChapterInput Assign menu Assigning the digital inputsOther Settings Other setup menuDynamic Range Control Setup Dual Mono SetupLFE Attenuator Setup SR+ Setup for Pioneer plasma displaysAdditional information Chapter TroubleshootingAdditional information Plus Refer to Using the surround back channel Extended mode onAdditional information See Operating other Pioneer components on Connecting the speakers onVSX-815/915 only The SR Additional information Resetting the main unit Switching the speaker impedancePress System Setup to confirm OK? shows in the displayAdditional information Specifications Amplifier sectionAudio section Video SectionPower cord caution Cleaning the unitAM Tuner Section MiscellaneousPioneer Corporation

VSX-815-S/-K, VSX-915-S/-K specifications

The Pioneer VSX-915-S/-K and VSX-815-S/-K are part of Pioneer's renowned line of AV receivers that provide home theater enthusiasts with an impressive range of features and technologies. These models are particularly recognized for their exceptional audio quality and versatility, making them ideal for both music lovers and movie enthusiasts alike.

One of the standout features of the VSX-915 is its Dolby TrueHD and DTS-HD Master Audio decoding capabilities, which allow users to experience high-definition audio quality that matches the latest in cinematic releases. This model is equipped with Pioneer's Multi-Channel Acoustic Calibration System (MCACC), enabling automatic speaker setup and optimization based on the room's acoustics. This technology ensures that listeners enjoy a balanced sound field, regardless of the room's layout.

The VSX-815 model, while slightly more compact, does not compromise on functionality. It retains essential features such as Dolby Digital EX and DTS 96/24 decoding, providing rich surround sound that enhances the home theater experience. The unit's direct energy HD amplification delivers robust audio output while maintaining low distortion levels, ensuring that high-frequency details are preserved without sacrificing power.

Both models include a robust selection of inputs and outputs, including HDMI connectivity, which supports 1080p video pass-through. This makes it compatible with a variety of modern devices, from Blu-ray players to gaming consoles. The VSX-915 also supports multi-zone audio distribution, allowing users to enjoy different sources in different rooms, which adds a layer of convenience for those who like to entertain.

Pioneer's proprietary technologies, such as the Phase Control, help in enhancing sound clarity, providing a more coherent audio experience. Additionally, both receivers feature a user-friendly graphical user interface (GUI) for easy navigation through settings and options.

In terms of design, both the VSX-915-S/-K and VSX-815-S/-K feature an elegant and functional aesthetic that fits well in any home entertainment setup. With their build quality and attention to detail, they are built to last while delivering superior sound quality.

In summary, the Pioneer VSX-915-S/-K and VSX-815-S/-K represent an excellent investment in high-quality home audio experiences, combining advanced technologies and user-friendly features that cater to both casual listeners and dedicated audiophiles.
Top Page Image Contents