Pioneer VSX-52TX manual Use cursor left/right to select Learn then press Enter

Page 51

Controlling the rest of your system

Programming signals from other remote controls

If the preset code for your component is not available, or the available preset codes do not operate correctly, you can program signals from the remote control of another component. This can also be used to program additional operations (buttons not covered in the presets) after assigning a preset code.

1While pressing the RECEIVER button, press and hold the 1 button.

The remote LCD display shows SETUP.

2Press the MULTI CONTROL button for the component you want to control.

The LCD on the remote displays the component you want to control.

•You can’t assign the RECEIVER button.

3 Use (cursor left/right) to select LEARN then press ENTER.

PRES KEY shows in the LCD display.

• To exit or cancel press RECEIVER.

4Point the two remote controls towards each other then press the button that will be doing the learning on this receiver’s remote control.

PRES KEY starts flashing to indicate the remote is ready to accept a signal.

•The remote controls should be 1–2 inches apart.

1 – 2 inches

5Press the corresponding button on the other remote control that is sending (teaching) the signal to this receiver’s remote control.

For example, if you want to learn the playback control

signal, press and hold for a couple of seconds. The LCD display will show OK if the operation has been learned.

If for some reasons the operation hasn’t been learned the LCD will display ERROR briefly and then display PRES KEY again. If this happens, keep pressing the (teaching) button as you vary the distance between the two remotes, until the LCD display shows OK.

09

Certain buttons represent operations that cannot be learned from other remote controls. The buttons available are shown below:

RECEIVER

INPUT

SOURCE

SELECT

 

 

DVD/LD

 

TV/SAT

DVR/VCR

TV CONT

 

 

MULTI CONTROL

 

CD

 

CD-R/TAPE

TUNER

RECEIVER

INPUT ATT

FL DIMMER

SR

 

+10

 

DISC

 

 

 

 

ENTER

D.ACCESS

 

 

 

CLASS

TOP MENU

 

 

 

MENU

 

 

TUNE

 

 

DTV MENU

ST

ST

 

T.EDIT

 

ENTER

BAND

 

 

 

SYSTEM TUNE

 

 

GUIDE SETUP

 

RETURN

 

 

TV CONTROL

 

TVVOL

 

INPUT

TV CH

VOL

 

 

SELECT

 

 

DTVON/OFF

 

REC

DTVINFO

MUTE

TUNER

 

 

RECSTOP

 

DISPLAY

 

 

 

MPX

 

CHRETURN

HDD

DVD

AUDIO

 

SUBTITLE

 

 

 

CH

CH

 

 

RECEIVER CONTROL

 

THX

 

STANDARD

ADV.SURR

STEREO

 

 

ACOUSTIC

SIGNAL

MIDNIGHT/

AUTO SURR

EQ

SELECT

LOUDNESS

SHIFT

 

EFFECT

SLEEP

DIALOG E

 

/CHSEL

RECEIVER

6To program additional signals for the current component repeat steps 4 and 5.

To program signals for another component, exit and repeat steps 1 through 5.

7Press the RECEIVER button to exit and store the operation(s).

Note

•Some commands from other remote controls cannot be learned, but in most cases the remotes just need to be moved closer together or farther apart.

•If the remote LCD shows ERROR, it may also mean the memory is full. See Erasing one of the remote control button settings below to erase a programmed button you’re not using to free up more memory.

• TV CONTROL buttons (TV ,TV VOL +/–,TV CH +/– and INPUT SELECT) can only be learned after selecting TV CONT.

51

En

Page 50 Page 52
Image 51
Page 50 Page 52
Contents VSX-52TX Information to User Wash hands after handlingImportant Safety Instructions Contents Additional information Other SettingsControlling the rest of your system Other connectionsChecking what’s in the box FeaturesBefore you start Before you start ChapterInstalling the receiver Before you start VentilationLoading the batteries Listening to Surround Sound Minute guide02 5 minute guide Chapter Introduction to home theaterConnect your speakers Minute guideFront speakers Surround speakers02 5 minute guide Enter Make sure ‘Normal SB’ is selected then pressFollow the instructions on-screen Checking the settings on your DVD or other player Other problems when using the Auto Mcacc SetupPlaying a source Connecting up Connecting up ChapterAbout cable types Connecting up When making cable connectionsAbout the video converter CD recorder DVD or LD player CD player Connecting up Connecting digital audio componentsTip Connecting up Connecting analog audio componentsConnecting multichannel analog components Output jacksDVD or LD player Connecting up Connecting video componentsConnecting to the front panel video terminal TV tunerAM loop antenna Connecting up Connecting antennasFM wire antenna Using external antennasFront speakers Connecting the speakersConnecting up Overhead view of speaker setupOperating other Pioneer components Power cord cautionView of 7.1 channel speaker setup AC outletFront panel Listening Mode SelectControls and displays Controls and displays ChapterControls and displays Controls and displays Display Sleep StereoMono TunedControls and displays Remote control Tuner Display 6TUNE/ST +/- /ENTERDTV ON/OFF DTV InfoOperating range of remote control unit Auto playback Listening to your systemListening to your system Chapter Listening in surround soundPRO Logic Using the Home THX modesUsing the Advanced surround effects Listening to your systemPress EFFECT/CH SEL again to adjust other settings Dolby Pro Logic IIx Music settingsNeo6 Music settings Use the +/- buttons to adjust the settingListening to your system Listening with Acoustic Calibration Choosing the input signalTo cycle the surround back channel options Listening to your system Using the surround back channelExtended mode Press Extended Mode front panel repeatedlyListening to your system Using the Virtual Surround Back Mode VirtualSBTo cycle the virtual surround back channel options Enhancing dialog Using the tone controlsPress SHIFT+DIALOG E to switch dialog enhancement on or off Press Tone to select the frequency you want to adjust30 min Using the sleep timerListening to your system Playing other sources Selecting the multichannel analog inputsSurround back speaker setting System Setup menuSystem Setup menu Chapter Making receiver settings from the System Setup menuSelect ‘MANUAL MCACC’ from the System Setup menu System Setup menuManual Mcacc speaker setup Select the surround back speaker settingFine Channel Distance Fine Channel LevelSetting the Acoustic Calibration EQ automatically Copying your Acoustic Calibration EQ settingsAcoustic Calibration EQ Setting the Acoustic Calibration EQ manually Checking your Acoustic Calibration EQ settingsFront Align Manual speaker setup Select the setting you want to checkSelect ‘Manual SP Setup’ then press Enter Select ‘Speaker Setting’ from the Manual SP Setup menu Speaker SettingChannel Level Crossover NetworkSpeaker Distance Select ‘Speaker Distance’ from the Manual SP Setup menuListening to the radio Using the tunerUsing the tuner Chapter Tuning directly to a stationAbcdefghijklmnopqrstuvwxyz Using the tuner Saving station presetsNaming station presets Listening to station presetsPrepare the recorder Making recordingsMaking recordings Chapter Making an audio or a video recordingControlling the rest of your system Chapter Setting the remote to control other componentsSelecting preset codes directly Controlling the rest of your systemPress the Receiver button to exit and store the operations Use cursor left/right to select Learn then press EnterErasing all of the remote control presets Confirming preset codesDirect function Disc Controlling the rest of your system Controls for TVsInput SelectSHIFT+ CD/MD/CD-R/DVD/LDShift + DVD Controlling the rest of your systemEnter Guide HDDOther connections Chapter Second Zone speaker B setupSwitching the speaker system Other connectionsBi-wiring your speakers Other connections Bi-amping your front speakersFront left Speaker Making multi-room connections Using the sub room controlsUsing the remote control in the sub room Other connections Multi-room listeningPress the Multi Room ON/OFF button on the front panel Using the front panel multi-room controlsUse the Master Volume dial to adjust the volume Other connectionsUsing this receiver with a Pioneer plasma display Other connections Connecting additional amplifiersUsing the SR+ mode with a Pioneer plasma display Pioneer plasmaDVD player Page Assigning the digital inputs Other SettingsOther Settings Chapter Input Assign menuAssigning the component video inputs Other SettingsOther Setup menu Select ‘Other Setup’ then press EnterChoose the setting that you want Dynamic Range Control SetupDual Mono Setup Select ‘DRC Setup’ from the Other Setup menuSelect ‘SR+ Setup’ from the Other Setup menu LFE Attenuator SetupSR+ Setup for Pioneer plasma displays Select ‘LFE ATT Setup’ from the Other Setup menuVolt Trigger Setup Multi Room SetupAdditional information Chapter TroubleshootingPower Additional informationNo sound Additional informationDigital inputs on Other audio problemsAudio components on VideoDisplay SettingsExtended Auto setting, the EX Remote controlAdditional information Resetting the main unit Switching the speaker impedancePress System Setup to confirm Dolby Additional information Surround sound formatsAdditional information About THX Cleaning the unit Additional information SpecificationsTo establish a safe level Once you have established a comfortable sound levelDecibel Level Example Pioneer Corporation

VSX-52TX specifications

The Pioneer VSX-52TX is a remarkable AV receiver that stands out in the realm of home theater systems, well-known for its high-quality sound performance and an array of advanced features. Designed to cater to the needs of audiophiles and casual listeners alike, the VSX-52TX integrates cutting-edge technologies that elevate the home entertainment experience.

One of the prominent features of the VSX-52TX is its 7.1 channel amplification system, providing a robust output of 120 watts per channel. This ensures that users can enjoy crystal-clear audio across various setups, whether it’s a simple stereo configuration or a full surround sound experience. The receiver supports a wide range of audio formats, including Dolby TrueHD and DTS-HD Master Audio, allowing for an immersive soundstage that brings movies, music, and games to life.

Incorporating Advanced MCACC (Multi-Channel Acoustic Calibration System), the VSX-52TX offers automatic speaker calibration, which fine-tunes the surround sound experience based on the unique acoustics of your room. This technology analyzes the speaker layout and optimizes the audio output for consistent and dynamic sound quality.

Another defining characteristic of the VSX-52TX is its extensive connectivity options. Equipped with multiple HDMI inputs, the receiver can handle various high-definition devices, making it easy to connect Blu-ray players, gaming consoles, and streaming devices. The inclusion of HDMI version 1.4 also allows for 3D video pass-through and Audio Return Channel (ARC), enhancing its versatility for modern home theaters.

The user-friendly interface of the VSX-52TX is complemented by its compatibility with network streaming. It supports popular services like Spotify, Pandora, and vTuner, enabling users to access their favorite content with ease. Additionally, the built-in USB port allows for easy playback of music files from USB drives.

The receiver showcases a sleek, modern design that integrates seamlessly into any home decor. The informative front display ensures that users can easily navigate through settings and features, while the remote control provides convenient access to all functionalities from a distance.

Overall, the Pioneer VSX-52TX is a powerful and versatile AV receiver that combines sophisticated technology with user-friendly features, making it an excellent choice for anyone looking to enhance their home theater experience. With superior audio capabilities, network streaming options, and advanced calibration technologies, the VSX-52TX continues to be a prominent choice for both music enthusiasts and movie lovers.
Top Page Image Contents