Trane RX-212 instruction manual Input & Output Specifications, With same type and rating

Input & Output Specifications

INPUT SPECIFICATIONS

Input		Actual	For Use
		Load	With
		Impedance	Nominal
	BAL –60	550 ohms	50 to 600
CHANNEL IN	BAL –40	800 ohms
			ohms
	BAL –20	900 ohms
	UN-BAL	25k ohms	10k ohms
ACCESSORY (RCV)		10k ohms	10k ohms
STEREO IN	AUX	10k ohms	10k ohms
	PHONO 47k ohms		4 7k ohms
AUXECHO IN		10k ohms	10k ohms
SUB IN		10k ohms	10k ohms

OUTPUT SPECIFICATIONS

		0dB is referenced to 0.775V RMS.
Sensitivity*	Input Level (Trim "0" to Trim "–30")		Connector
	Nominal	MAX. Before Clip
–80dB (0.08mV)	–60dB (0.78mV) to –30dB (25mV)	–40dB (7.8mV) to –10dB (250mV)	XLR-3-31
–60dB (0.78mV)	–40dB (7.8mV) to –10dB (250mV)	–20dB (78mV) to +10dB (2.5V)
			type**
–40dB (7.8mV)	–20dB (78mV) to +10dB (2.5V)	0dB (775V) to +30dB (25V)
–50dB (2.5mV)	–30dB (25mV) to 0dB (775mV)	–10dB (250mV) to +20dB (7.8V)	PHONE JACK
-20dB (78mV)	–0dB (775mV)	20dB (7.8mV)	3P PHONE
			JACK***
–40dB (7.8mV)	–20dB (78mV)	+10dB (2.5V)	RCA
–70dB (0.25mV)	–50dB (2.5mV)	–20dB (78mV)	PIN JACK
-40dB (7.8mV)	-20dB (78mV)	0dB (775mV)	PHONE JACK
–10dB (250mV)	+4dB (1.23mV)	+24dB (12.3mV)	PHONE JACK

0dB is referenced to 0.775V RMS.

Output Level

Output	Actual Source Impedance	For Use With Nominal	Nominal	MAX Before Clip	Connector
PGM L					XLR-3-32
LINE OUTPGMR	100 ohms	600 ohms	+4dB (1.23V)	+20dB (7.8V)	type**
					and
FBl
FB2					PHONE JACK
+4	90 ohms		+4dB (1.23V)	+20dB (7.8V)	PHONE JACK
ECHOSEND -20	64 ohms	600 ohms	–20dB (78mV)	-4dB (490mV)	PHONE JACK
REC OUT	1k ohms	10k ohms	–10dB (250mV)	+10dB (2.5V)	RCA PIN JACK
ACCESSORY (SEND)	1k ohms	10k ohms	0dB (775mV)	+20dB (7.8V)	3P PHONE JACK***
PHONES	18 ohms	8 ohms or higher	75mW/8 ohms,	370mW/8 ohms,	STEREO
			0dB (775mV)	+7dB (1.7V)	PHONE JACK****

*Sensitivity is the level required to produce a nominal speaker output level.

**All XLR type connectors are floating, balanced and transformer-isolated.

***ACCESSORY jacks (3P PHONE JACK) are wired: Tip=Receive, Ring=Send and Sleeve =Common

****Stereo phone jack is wired: Tip=Left, Ring=Right and Sleave=Common

Note:

As is described in the beginning of the operation manual, the XLR type connectors of the RX-208, RX-212 and RX-216 are wired as follows. Pin No. 1 — Ground

Pin No. 2 — Cold (Low)

Pin No. 3 — Hot (High)

Specifications are subject to change without notice.

Caution:

The fuse rating for 120V AC operation is 2 amps., and 1 amp. for 220/240V AC operation. The fuse must always be replaced

with same type and rating.

- 15 -