Revolabs 03-hdvenujp, 03-hdvenucn, 01-hdvenu, 03-hdvenueu Revolabs HD VenueTM Charger Base

Page 20

Note: Microphones in new systems must be paired to the Base Station with each microphone assigned to a unique channel on the Base Station.

Remember, microphones are always muted (flashing RED LED) when they are removed from the Charger Base and the Mute button needs to be pressed to make it ―live‖ (flashing GREEN LED).

A microphone that is not paired will be indicated by a cycling RED-GREEN LED pattern. A Base Station channel that is not paired to a microphone will not show any activity on the channel LED (make sure unit is first powered on by observing GREEN backlit front panel display).

When channels are paired, both microphone and channel LEDs will flash RED as microphones are removed from the Charger Base and flash GREEN when un-muted. Remember that only one microphone can be paired to any single Base Station channel.

To pair an individual microphone to the Base Station:

1.Turn the microphone OFF (no LED activity). If the microphone is ON, press and hold the Mute button for 10 seconds until the LED turns solid RED then release the button to turn the unit off. (do not release the button when you hear two beeps).

2.Place the microphone unit into pairing mode by holding the Mute button down for seven seconds. The LED will turn solid RED. Release the Mute button. The microphone is now in pairing mode.

3.Within one minute, push and hold the button for the desired channel on the Base Station for seven seconds until the LED turns solid red then release. The LED for that channel will be solid red until pairing starts, as indicated by a quick GREEN flash, then switching to flashing RED on both the microphone and the Base Station (muted audio). Pairing is now complete.

Revolabs HD VenueTM Charger Base

When microphones are not in use, they should be properly inserted into the Revolabs HD Charger Base. It is important to ensure that all system microphones are inserted fully in the base so that charging will occur. Features of the base are shown in the following figure.

3

2

 

1

1.LED indicator — power status indicator

2.Charger Bays — charges up to 2 Microphones

3.Power Cord Receptacle — power supply input, 9-24VDC (on rear)

-20 -

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Revolabs HD Venue Wireless Microphone System D V N U M a N P a P 1 1 M a R C H 2 0 1 2 R e v 2 Contents Safety and General Information Export Law Assurances Hdvenu North America Upcs Usage RestrictionHdvenueu European Union Usage Restriction European ComplianceIntroduction System ComponentsInstalling the Revolabs HD Venue Base Station To Install the Base StationRevolabs HD Venue Base Station Connections Rear ViewConfiguring the Revolabs HD Venue TM Base Station ∙ How large is the room?Using the Rear Panel Configuration DIP Switches Configuration Settings DIP Switch 1- Output MixingDIP Switch 2 Low Pass Filter DIP Switch 3 Audio Output LevelUsing the Revolabs HD Control Panel Software DIP Switch 5&6 Sharing ModeDIP Switch 7&8 Transmit Power Configuration SettingsMics Unmute at Startup All Mic MuteLock MuteUsing the HD Wearable Wireless Microphones Revolabs HD Microphones and HD Microphone AdaptersPage Adjusting the Volume on the Wearable Microphone Earpiece 360 ºPickup PatternTo use the HD Directional Tabletop Microphone Using the HD XLR Microphone Wireless Adapter Using the HD Wireless Adapter for Countryman Microphone Pairing Wireless Microphones to Base Station Revolabs HD VenueTM Charger Base Power Module Updating the Revolabs Hdtm FirmwareCharging the Microphone Batteries Updating the HD Venue Base Station and HD MicrophonesRevolabs HD Indicator LEDs YELLOW, GreenWarranty Specifications Dimensions, L, W, H and WeightIndex Connections, 8D V N U M a N P a P 1 1 M a R C H 2 0 1 2 R e v 2
Top Page Image Contents