Creative PCA-6780 user manual

Page 5

This device complies with the requirements in FCC part 15 of the FCC rules: Operation is subject to

the following two conditions:

1.This device may not cause harmful interfer- ence, and

2.This device must accept any interference received, including interference that may cause undesired operation

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These lim- its are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio commu- nications. Operation of this device in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his/her own expense. The user is advised that any equipment changes or modifications not expressly approved by the party responsible for compliance would void the compliance to FCC regulations and therefore, the user's authority to operate the equipment.

Caution!

Achtung!

There is a danger of a new battery exploding if it is incorrectly installed. Do not attempt to recharge, force open, or heat the battery. Replace the battery only with the same or equiv- alent type recommended by the manufacturer. Discard used batteries according to the manufac- turer’s instructions.

v

Image 5
Contents PCA-6780 Acknowledgements CopyrightPacking List Additional Information and Assistance Page Page Contents Appendix a Programming Gpio & Watchdog Timer Table B.5IR Connector Appendix C General Information Introduction Specifications FeaturesStandard SBC Functions System chipsets Intel 852GM +ICH4Solid State disk Display InterfaceEthernet interface Mechanical and EnvironmentalBoard layout dimensions component side Board layout dimensionsPage Installation Jumpers JumpersConnectors ConnectorsLocating Connectors solder side Locating Connectors component sideSetting Jumpers Clear Cmos J1 Clear Cmos J1Lvds Panel Power Select Lvds Panel Power Select JP1COM2 RS-232/422/485 Select J2 COM2 RS-232/422/485 SelectATX power Connector CN5 Installing SODIMMsCompactFlash CN22 Printer port Connector CN4CompactFlash Socket Connecting the floppy drive Floppy Connector CN3Connecting the hard drive IDE Connector CN2Lvds LCD panel Connector CN8 CRT display Connector CN10LCD Inverter Connector CN6 15 VGA/LVDS interface connectionsEthernet configuration USB Connectors CN9,CN11LAN Connector CN13 Network bootReset Pin7&Pin8 HDD LED/Reset/Power Button CN1Power Button Pin9&Pin10 HDD LED Pin1&Pin2,Pin3&Pin4,Pin5&Pin6Mini Keyboard Connector CN17 COM port Connector CN14,CN15External Keyboard Connector CN18 Audio Interface Connector CN7Page Bios Operation Bios Introduction Control Keys Bios SetupMain Menu Set Password Load Optimized DefaultsSave & Exit Setup Exit Without SavingStandard Cmos Features Base Memory Halt onExtended Memory Total MemoryAdvanced Bios Features Swap Floppy DriveDisabled First / Second / Third / Other Boot DriveBoot Up Floppy SeekDisabled Boot Up NumLock StatusDisabledVideo Bios ShadowEnabled Security OptionSetupFull Screen Logo ShowEnabled MPS Version Control for OS1.4Advanced Chipset Features Video Bios CacheableDisabled System Bios CacheableEnabledMemory Hole At 15M-16MDisabled Delayed Transaction EnabledOn-Chip Frame Buffer Size 32MB On-Chip VGA EnabledBoot Display Vbios Default OnChip IDE Device Integrated PeripheralsOnboard Device Super IO DeviceAcpi FunctionEnabled Power Management SetupRun VGA Bios if S3 ResumeAuto Power ManagementMin SavingHDD Power Down Mode15 Min Suspend Mode 1 HourSoft-Off by PWR-BTTNEnabled Wake-Up by PCI cardEnabledResume by AlarmDisabled USB KB Wake-Up From S3Enabled7 PnP/PCI Configurations Current System/CPU Temp Show Only Shutdown Temperature DisabledPC Health Status Spread Spectrum Disabled Auto Detect PCI Clk EnabledCPU Host/SRC/PCI Clock Default Frequency/Voltage ControlLoad Optimized Defaults To Change Password Set PasswordTo Establish Password To Disable Password Quit Without Saving Save & Exit SetupPage Page Driver Installation Step Driver IntroductionInstall Intel INF Update Driver for Windows XP/2000 Driver InstallationInstall Intel Graphic Driver for Windows XP 2000 Install Audio Driver for Windows XP/2000Page Programming Gpio & Watchdog Timer Gpio Registers Appendix a Programming Gpio & Watchdog TimerSupported Gpio Register Gpio Example program-1 MOV DX,2EH MOV AL,AAH OUT DX,AL Watchdog programming Page Pin Assignments Appendix B Pin Assignments HDD LED/Reset/Power Button CN1Table B.1 HDD LED/Reset/Power Button CN1 Table B.2 Primary IDE Connector CN2 Primary IDE Connector CN2Table B.3 Floppy Connector Floppy ConnectorIR Connector Printer Port ConnectorTable B.4 Printer Port Connector Table B.5 IR ConnectorTable B.8 Lvds Connector CN8 Lvds Connector CN8Audio Interface CN7 Table B.7 Audio Interface CN7SUB VGA Connector CN10 USB port 1, 2 Connector CN9USB port 3,4 Connector CN11 12 PC 104 ConnectorCOM port 2 RS-232/422/485CN15 LAN RJ45 Connector CN13COM port 1 RS-232CN14 17 KB/MS Connector CN17 ATX Power Connector CN16External KB/mouse Connector CN18 ISA Gold Finger CN19 ATX Suspend Power Connector CN20Table B.19 Negative Power Input CN21 Negative Power Input CN21CF Connector CN22 3 232/422/485 SEL J2 Lvds Voltage Choose JP1Table B.20 Lvds Voltage Choose JP1 Table B.21 Clear Cmos J1Page System Assignments Table C.1 System I/O ports Appendix C System AssignmentsSystem I/O Ports Table C.2 1st MB memory map 1st MB memory mapTable C.3 DMA channel assignments DMA channel assignmentsTable C.4 Interrupt assignments Interrupt assignments