Crest Audio X 18R, X 20R owner manual AUX 5 and AUX 6 are post-fader AUX 5 and AUX 6 are pre-fader

Page 27

Stereo Input Channel 2

AUX Send Features

Six auxiliary sends are available for creating individual output mixes. These can be used to drive effects processors, provide monitor mixes, create broadcast or alternate sound rein- forcement mixes, or for other special requirements.

NOTE: The default PRE setting for the Auxes is pre-fader, but post-mute, post-insert, and post-EQ. Internal settings can be changed so that PRE is also pre-EQ and pre-mute (See Mono Input Channel NOTE).

Aux 1 - 2 PRE

AUX 1/2 stereo pair is post-fader.

AUX 1/2 stereo pair is pre-fader.

Aux Sends 1 & 2

Auxes 1 and 2 are permanently configured as a stereo pair. If the channel is configured as a stereo input, the Left and Right signals are routed to Auxes 1 and 2, retaining the stereo split.The PAN knob acts as a balance control.This stereo aux send can be used for any type of stereo feed from the console, such as live two-track recording, stereo in-ear monitors, alternate stereo feed for broadcast and stereo signal processors.Also, by using the pan control to select a single bus, Auxes 1 and 2 can be used as discrete mono Aux buses.

Aux 1/2 Level Sets level for the Aux 1/2 stereo pair.

Aux 1/2 PAN If the SUM INPUTS button is up, this knob controls the stereo balance of the channel signal into Auxes 1 and 2. If the SUM INPUTS button is down, the summed channel signal is panned between Auxes 1 and 2.

Aux Sends 3, 4, 5 & 6

Auxes 3, 4, 5, & 6 are configured as individual mono aux sends.They are typically used to feed signal processors and on stage monitors. Stereo signals are summed together to make up the source for Auxes 3, 4, 5 & 6.

AUX 3-4 PRE

AUX 3 and AUX 4 are post-fader.

AUX 3 and AUX 4 are pre-fader.

Auxes 3, 4, 5, & 6 Level Set Levels Auxes 3, 4, 5, & 6.

AUX 5-6 PRE

AUX 5 and AUX 6 are post-fader.

AUX 5 and AUX 6 are pre-fader.

p. 27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents 18R / X 20R Page Important Precautions Page Important Safety Instructions Wichtige Sicherheitshinweise Instructions Importantes De Securite Instrucciones Importantes Para Su Seguridad Table Of Contents 18R/20R Block Diagram How To Use This Manual Mono Input Channel Hz Lo-Cut Filter Lo Cut SwitchLine Input Mic Pad GainMono Input Channel Low Frequency-LF High Frequency-HFHigh Mid-HM Low Mid-LMModule Block Diagram Controls AUX 3-4 PRE Aux 1 2 PREAux Sends 1 Aux Sends 3, 4, 5Mono Input Channel PFL MuteRear Panel Chan Insert Jack 48V Phantom PowerLine Input Jack XLR Mic Input JackStereo Input Channel SUM Inputs Str Line In Mic PadModule Low Frequency-LM Front Panel Features Stereo EQStereo Input Channel AUX 5 and AUX 6 are post-fader AUX 5 and AUX 6 are pre-fader Stereo Input Channel Input Fader BAL ControlRear Panel Block Diagram +48V On Master Section Solo OFF From MonitorTape Master Section PWR LED Solo LEDMaster Section Aux 3, 4, 5, & 6 AFL AUX OUT 1-2 Level ControlAux 1-2 AFL AUX OUT 3, 4, 5 & 6 Level ControlMaster section Left Assignments For Groups 1, 2, 3 GroupPK / SIG LED IndicatorsGROUPAssignment Section Mono assignments for Groups 1, 2, 3Block Diagram Controls Monitor Output Section Monitor Level ControlSUM Mono Module Block Diagram Controls Mono Source SelectMaster Section MONO, Left & Right Master faders 100mm Mono PK/SIG LEDLeft/Right PK/SIG LED Mono AFLMaster Section Left, Right And Mono Main Outputs Left, Right and Mono Bus InputsGroup 1, 2, 3 & 4 Bus Inputs Insert For Left, Right and MonoRear Panel Block Diagram Group Inserts 1Thru Aux Insert 1ThruAux Outtrs Jacks 1Thru Aux OUT XLRs 1ThruMaster Section Solo Link Tape LineAlt Out Monitor OutSpecifications 18R/20R Internal Options Connector Pinout DetailUser Notes User Notes Crest P/N
Top Page Image Contents