DJ Roller Safety Precautions, DJ Roller Features

DJ Roller™	Safety Precautions

•Do not spill water or other liquids into or on to your unit.

•Be sure that the local power outlet match that of the required voltage for your unit.

•Do not attempt to operate this unit if the power cord has been frayed or broken. Please route your power cord away from foot trafﬁc.

•Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used to reduce the risk of electrical shock and ﬁre in case of an internal short.

•Disconnect from main power before making any type of connection.

•Do not remove the top cover under any conditions. There are no user serviceable parts inside.

•Never plug this unit in to a dimmer pack

•Always be sure to mount this unit in an area that will allow proper ventilation. Allow about 6” (15cm) between this device and a wall.

•Do not attempt to operate this unit if it becomes damaged in any way.

•Never operate this unit when it’s cover is removed.

•To reduce the risk of electrical shock or ﬁre, do not expose this unit rain or moisture

•This unit is intended for indoor use only, use of this product outdoors voids all warranties.

•During long periods of non-use, disconnect the unit’s main power.

•Always mount this unit in safe and stable matter.

•Power-Cord Protection -Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the fixture.

•Cleaning -The fixture should be cleaned only as recommended by the manufacturer.

•Heat -The fixture should be situated away from heat sources such as radiators, heat registers, stoves, or other appliances (includ- ing amplifiers) that produce heat.

•The fixture should be serviced by qualified service personnel when:

A.The power-supply cord or the plug has been damaged.

B.Objects have fallen, or liquid has been spilled into the appliance.

C.The appliance has been exposed to rain or water.

D.The fixture does not appear to operate normally or exhibits a marked change in performance.

DJ Roller™	Quick Start

Master/Slave Quick Start Stand Alone Mode

Connect up to four units together via XLR cables. The master unit will run the slaves to the masters built in programs and internal microphone. Plug in all units. When the DJ Roller™ is first turned on, it will run through an internal self test where it resets all motors to their zero position. After the self test the units will react to sound, and chase to the several built in programs.

DJ Roller™	Features

The DJ Roller™ features a bright 150 watt/500 hour lamp life halogen bulb with a separate gobo and color wheel. The color wheel features seven brilliant colors plus white and the gobo wheel features 9 gobos plus a large and small spot. This units is ready to be installed or hung and powered right out of the box. There is no assembly required. This fixture incorporates the use of high quality stepper motors for a more accurate mirror movement. Mirror movement allows for a full 90 degree tilt (vertical) and a full 90 degree pan (horizontal). An internal built in microphone allows the fixtures to run in Stand Alone mode so there is no need for an external controller. The DJ Roller™ may also be set-up to run in a Master-Slave mode when used in multiples, up to 16 units. When used in the Master-Slave mode, the unit will chase to several internal programs. The DJ Roller™ can also be controlled via a standard DMX controller such as the American DJ Show Designer,™ or the American DJ® DMX Operator,™ giving the user independent control over the gobo and color wheel as well as the mirrors pan and tilt movements.

•ZB-JCR/H5 15V/150W, 500Hr Lamp.

•DMX-512 Compatible.

•Stepper motors for smooth movements.

•7 colors plus white.

•10 Gobos plus spot.

•Master/Slave Operation

•Built-in microphone.

•Sound sensitivity knob.

•One year warranty.

•Sound Active.

•Optional MINI/C controller, for blackout control.