DMX MODE
Using the 1 thru 3 mode dipswitches you can control the intensity, duration, rate by DMX in 7 different ways with a
|
| DMX Function |
|
|
|
| DMX Data Assignments |
|
| ||||||
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 10 | 1 | 2 | 3 | 4 |
|
|
|
on |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 10 | 1 | 2 | 3 | 4 | Duration is | Rate is set by DMX |
|
|
|
|
|
|
|
|
|
|
|
|
| Intensity is first |
| ||
on |
|
|
|
|
|
|
|
|
|
|
| DMX byte | 1/2 cycle | refresh** |
|
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 10 | 1 | 2 | 3 | 4 |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Intensity is | Duration is first | Rate is set by DMX |
|
on |
|
|
|
|
|
|
|
|
|
|
| preset | DMX byte* | refresh** |
|
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 10 | 1 | 2 | 3 | 4 |
| Rate is set by DMX USED WITH | |
|
|
|
|
|
|
|
|
|
|
|
| Intensity is first | Duration is second | ||
on |
|
|
|
|
|
|
|
|
|
|
| DMX byte | DMX byte* | refresh** |
|
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 10 | 1 | 2 | 3 | 4 | Duration is | Rate is first DMX |
|
|
|
|
|
|
|
|
|
|
|
|
| Intensity is |
| ||
on |
|
|
|
|
|
|
|
|
|
|
| preset | 1/2 cycle | byte |
|
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 10 | 1 | 2 | 3 | 4 |
| Rate is second DMX |
|
|
|
|
|
|
|
|
|
|
|
|
| Intensity is first | Duration is |
| |
on |
|
|
|
|
|
|
|
|
|
|
| DMX byte | 1/2 cycle | byte |
|
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 10 | 1 | 2 | 3 | 4 | Duration is first | Rate is second DMX |
|
|
|
|
|
|
|
|
|
|
|
|
| Intensity is |
| ||
on |
|
|
|
|
|
|
|
|
|
|
| preset | DMX byte* | byte |
|
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 10 | 1 | 2 | 3 | 4 | Duration is second | Rate is third DMX |
|
|
|
|
|
|
|
|
|
|
|
|
| Intensity is first |
| ||
on |
|
|
|
|
|
|
|
|
|
|
| DMX byte | DMX byte* | byte |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
*By setting duration for a long enough period, latch on is possible
**Performance of Strobes will depend heavily on the intelligence and versatility of the DMX board when rate is set by the DMX refresh. Higher rates can be achieved if smaller data packets are sent more often.
For modes that use only 1 DMX channel, units should be addressed sequentially
For modes that use 2 DMX channels, units should be addressed at every other address For modes that use only 3 DMX channel,units should be addressed at every 3rd address
Intensity from DMX | Values from 0 to 255 are useable |
|
|
| Values from |
| will flash the lamp for approx. 2 milliseconds, |
Duration byte from DMX | 255 will flash lamp for 5 seconds on AC 230V |
| 50 Hz supply; On a 120 AC line with ,value 0 |
| will last 3 milliseconds, value 255, 4 seconds. |
|
|
| Values from |
| will flash the lamp every 4 seconds |
Rate byte from DMX | on AC 230V 50 Hz supply; On a |
| 120 AC line with Value 0 |
will flash every 6 seconds.On a 120 AC line with transformer. The highest rate is 50 or 60 flashes per second
American DJ ® LOS ANGELES, CA. 90058 USA - SNAP SHOT DMX/D PG.3