PROGRAM SECTION
1 | INPUT 2 |
|
| INPUT 3 | ||
PHONO 2 | LINE 2 | PHONO 3 | LINE 3 | |||
|
|
| PGM 2 |
| ||
2 | INPUT |
|
|
|
| |
ASSIGN |
|
|
|
| ||
| 1 |
|
|
|
| |
| 2 | 3 |
|
|
| |
|
|
| 4 |
|
| |
|
| GAIN |
| BAL |
| |
|
|
|
|
| ||
3 |
|
|
|
|
|
|
4 | MIN | MAX | L | R | ||
| ISOLATOR |
| ON |
| ||
5 |
|
|
|
| OFF |
|
| LOW |
| MID | HI |
| |
6 | +6dB |
|
|
|
| +6dB |
|
|
|
|
|
| |
|
|
| ||
| FILTER |
|
|
|
| DRY |
| SWEEP | |
7 |
|
|
|
|
8 | FILTER | MIN | MAX | |
|
|
| ||
AUX 1 |
| AUX 2 |
| |
9 |
|
| ||
PRE |
|
| ||
OFF |
|
| ||
POST |
|
| ||
C.F. ASSIGN |
| CUE | ||
A | B |
|
|
|
10 | MASTER |
| OFF | ON |
|
|
|
| |
11 | PGM 2 |
| ||
| LEVEL |
|
| |
12 |
|
|
|
|
qINPUT SELECT SWITCH
Used to select input source from either PHONO or LINE.
wINPUT ASSIGN SWITCH
Used to assign the signal from each input, INPUT1 to INPUT4, to be sent to each PGM.
ePGM GAIN CONTROL
Adjusts the input level of each PGM. Set INPUT FADER (!2) to
rPGM BALANCE CONTROL
Adjusts the stereo balance for each PGM. Can be used for adjusting an unbalanced stereo image. Clockwise rotation from center position increases
the volume of R over L channel. A counter clockwise rotation increases the volume of L channel over R.
tISOLATOR ON/OFF SWITCH
When set to "OFF", a full range signal is transmitted regardless of the position of any isolator controls.
yISOLATOR [HI/MID/LOW]
Cuts and boosts each frequency range. The level is flat when this knob is set at center (click point). Each frequency range can be boosted up to +6dB when this knob is pushed fully up. Pushing down will cut each frequency range.
uDRY-FILTER MIX FADER
Allows control of the signal balance between dry and effect (FILTER) sound. When the fader is located at center, each signal level is the same.
iSWEEP CONTROL
You can control peak point of band pass filter. When you rotate clockwise, the point is moved towards higher frequency. Rotating
oAUX ASSIGN SWITCH
This switch enables the signal from each program to be sent to EFFECT SEND JACK ($1). Different signal routes can be selected by moving this switch to the following different positions;
PRE: The signal before the input fader (after the EQ) will be sent to AUX output.
OFF: No signal will be sent to AUX output.
POST: The signal after the input and crossfader will be sent to AUX output.
!0C.F. ASSIGN SWITCH
Used to send the signal from each program to either side of the crossfader (A or B) or direct to the master. "A" for left side of the crossfader, "B" for right side.
!1CUE SWITCH
Used to send the signal from each program to the monitor section for headphone monitoring.
!2INPUT FADER
Used to adjust the Input level of each program. Usually set to
TO CHANGE THE FADER UNIT".
6