Vestax PMC37Pro owner manual Rear Panel

Page 9

REAR PANEL

 

39

 

40

 

 

 

41

 

 

 

 

 

42

 

 

 

 

WARNING;SHOCK HAZARD-DO NOT OPEN.

 

 

C A U T I O N

 

 

 

 

 

 

 

 

 

AVIS;RISQUE DE CHOC ELELCTRIQUE -NE PAS OUVRIR.

 

 

RISK OF ELECTRIC

 

 

 

 

 

 

 

 

 

 

 

SHOCK. DO NOT OPEN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

R

MASTER

OUTPUT

SUB MASTER

L R

AUX 2

EFFECT SEND AUX 1

L R

AUX 2

EFFECT RCV

AUX 1

L

SUB MIC

 

L R

 

 

 

L R

 

 

 

 

L R

 

 

 

 

 

SERIAL NO.

 

LINE 4

 

LINE 3

 

LINE 2

 

 

 

LINE 1

 

MAIN MIC

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

MADE IN CHINA

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

UNDER LICENCE OF

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

VESTAX TOKYO,JAPAN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

POWER

R

 

L R

 

L

R

L

R

L

R

 

L

 

 

 

 

 

AC 12V

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

REC OUT

 

PHONO 4

 

PHONO 3

 

PHONO 2

 

 

PHONO 1

 

 

 

 

 

 

 

GND

 

GND

 

GND

 

GND

PROFESSIONAL MIXING CONTROLLER

 

31

32

33

 

 

34

 

 

 

 

 

 

35

36

37

38

#1POWER SWITCH

Use to turn power on.

#2POWER INPUT JACK

Connect the AC-12A, AC adaptor (12V AC, 1000mA).

#3REC OUTPUT JACK [RCA PIN JACK]

Connect to the input jack of the tape recorder, MD, DAT, etc. The output level of this jack is fixed and does not change with the MASTER LEVEL VOLUME (!9).

#4GROUND TERMINAL

Connect this terminal to the ground lead of the turntables.

#5PHONO INPUT JACK [RCA PIN JACK] Connect turntables equipped with MM (Moving Magnet type) cartridge. The signal from the turntable is fed to the PGM channels when Phono input is selected.

#6LINE INPUT JACK [RCA PIN JACK]

Connect the equipment with line level output (-10dB or 0dB), such as CD players, tape decks, DATs, MDs, etc. The signal from line level equipment is fed to the PGM channels when Line input is selected.

#7MAIN MIC JACK [XLR/pin 2:HOT]

Input jack for MAIN MIC.

#8SUB-MIC JACK [1/4" PHONE JACK] Input jack for SUB MIC.

#9MASTER OUTPUT JACK [1/4" TRS BALANCED JACK]

Connect to the input of power amp.

Tip-----HOT

Ring----COLD

Sleeve--GROUND

HOT

COLD

GND

fig-B. T.R.S JACK

$0SUB MASTER OUTPUT JACK [1/4" PHONE JACK] Connect to input of power amp as monitor in DJ booth or as a separate sound zone for entrance foyer etc.

$1EFFECT SEND JACK [1/4" PHONE JACK]

Connect to the input of the external effects. (Delay, Reverb etc)

$2EFFECT RECEIVE JACK [1/4" PHONE JACK] Connect to the output of the external effects. Can also be used as an extra input jack.

9

Image 9
Contents Professional Mixing Controller CONGRATULATIONS! ContentsRead Before Operating Equipment Important SafeguardsR R a N T Y A T U R E S FunctionsTOP Panel 1CUE Switch 0C.F. Assign SwitchProgram Section 2INPUT Fader8MASTER Balance Volume 7POWER Indicator9MASTER Level Volume @0SUB-MASTER Level Volume@6SUB MIC Level Volume @5MAIN MIC Level Volume@9AUX Send Level Volume #0AUX Receive Level VolumeRear Panel HOW to Remove the TOP Panel HOW to Change the Fader UnitHOW to Change the Fader Unit HOW to Replace the Input Fader Unit with IF-05PCVConnection Diagram example Specifications