FADER CLEANING AND REPLACEMENT
remove the slider assembly (C), ensuring that the wiper contacts (D) are not damaged as this will affect the operation of the fader. Clean the slid - er assembly by gently wiping the wiper contacts and slider bearings (E) using a tissue or cotton bud. If slider bearing are exessively worn, as indi- cated by exessive slider rocking then contact Stanton for replacement.
SA-12 FUNCTIONS & FEATURES
It’s only the 3x champion, DJ Craze signature mixer! This battle mixer has the all the quality of a club mixer and meets all the requirements of today's Turntablist. After years in the making the ultimate Scratch DJ mixer is here and ready for bat- tle.
3.Remove the single upper screw on the opposite end block to remove the guide rail. Clean the guide rail (F) with a tissue or
cloth, removing all traces of dirt and conta - |
|
mination. | G |
|
4.Remove the fader track (G) by slowly with - drawing from the unit. Place fader track on
desk or working surface with black contacts facing upwards. If necessary, the track can be washed in warm water, wiped gently then dried thoroughly using a dry cloth. Use a lint free
cloth or swab to wipe the tracks and check for marks along
the track. (Note: Lint free cloth should be used to avoidI dust/fibres being deposited on the track). If the track appears exessively worn, or if cleaning does not improve operation, replacement may be necessary.
5. Examine the center channel of the fader body and if dirty, clean using cot - |
ton buds. |
6. |
6.1) Secure the end block and guide rail onto the fader body. |
6.2) Insert track into the fader body. |
6.3) Insert slider assembly onto guide rail and into the fader body. Move |
slider from end to end to disperse the oil evenly. Carefully wipe away any |
Removable Effects Module
The MOD1 removable effects module includes 3 effects: Pitch Shifter, Flanger, and Delay. All effects have adjustable parameters and levels, can be assigned (turned on / off) to all channels or master output, and can be turned ON/OFF using any standard footswitch via the remote Start output.
OS2 Optical Scratch Switch
These ultra quiet, non friction phono/line switches allow you to trans- form without the clicking or static noise found in other line switches. Now including a special feature that locks the last position of the switch.
FEATURES:
3 position Cue Select
This switch allows you to set your cue source to PFL/Pre
Mic/Line Channel
The
excess oil using a tissue or cloth. |
6.4) Lubricate the guide rail by placing one drop of silicon liquid oil onto |
the guide rail (F). |
6.5) Insert dust cover. |
6.6) Insert fader track back into fader body with wires coming out open |
end of fader body. |
6.7) Secure the remaining end block ensuring that the track wires (I) are |
not pinched between the endblock and fader casing. |
7. Once assembled, move the slider from end to end to ensure operation is |
smooth. |
8. Attach fader to fader plate. (NOTE: As noted earlier if you do not want to |
change positioning of fader, keep the 2 fader plate screws loose and shift |
the fader until it is aligned with the marks you created in step 1, then tight- |
en fader plate screws.) |
•Focus Fader V2 Digital Optical Crossfader (Patent Pending) with curve adjustment and reverse switch.
•OS2 (Patent Pending) Optical Scratch switches with lock feature
•Removable effects module (Patent Pending).
•Effects fully assignable
•Foot pedal output to control effects.
•3 position cue select (Patent Pending) Pre CF Cue / Post CF Cue / Master.
•2 line, 2 phono, and 1 mic/line (switch - able) inputs.
•Program Reverse.
•3 band EQ with complete kill, Gain, and Pan control per channel.
•Program Faders reverse switches & curve adjustments.
•Headphone mute.
•Cue Pan Fader
•Dual headphone inputs (1/4 and 1/8
•TRS balanced Master output.
•
•Output Trim control.
•