Multiquip WC-62S manual WC-62P/S Concrete Mixer Rules for Safe Operation, Emergencies

Page 10

WC-62P/S CONCRETE MIXER — RULES FOR SAFE OPERATION

■NEVER run engine without air cleaner. Severe engine damage may occur.

■ALWAYS read, understand, and follow procedures in Operator’s Manual before attempting to operate equipment.

■ALWAYS be sure the operator is familiar with proper safety precautions and operations techniques before using roller.

■ALWAYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children.

■NEVER leave the mixer unattended, turn off engine or electric motor when unattended.

■CAUTION must always be observed while servicing this mixer. Rotating parts can cause injury if contacted.

■Unauthorized equipment modifications will void all warranties.

■Ensure that any extension cable is protected against damage and not liable to be tripped over or trapped underneath the mixer.

■DO NOT allow extension cord to come into contact with water or fluids.

■DO NOT spray water onto electric motor.

■This mixer is intended for the production of concrete. Mixer must be used only for its intended purpose.

■This mixer is not suitable for the mixing of flammable or explosive substances.

■NEVER operate the mixer in an explosive atmosphere.

■Before starting the mixer, check that all guards are in position and correctly fitted.

■Keep area around the mixer clear of obstructions which could cause persons to fall onto moving parts.

■ALWAYS ensure mixer is on level ground before mixing.

■Become familiar with the controls of the mixer before operating.

■ALWAYS replace any worn or damaged warning decals.

■Ensure the drum is rotating while filling and emptying the drum.

■ALWAYS disconnect AC power plug from power source before moving mixer (electric model only).

■High Temperatures – Always stop engine and allow the engine to cool before adding fuel, oil or performing service and maintenance functions. Contact with hot components can cause serious burns.

■NEVER disconnect any "emergency or safety devices". These devices are intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm or even death! Disconnection of any of these devices will void all warranties.

■If mixer is equipped with an electric motor, operate electric motor only at the specified voltage indicated on the nameplate.

■Make sure the OFF/ON power switch on the electric motor is always in the OFF position before inserting the mixer's power plug into an AC receptacle (electric model only).

Maintenance Safety

■NEVER lubricate components or attempt service on a running machine.

■ALWAYS allow the machine a proper amount of time to cool before servicing.

■Keep the machinery in proper running condition.

■Fix damage to the machine immediately and always replace broken parts, or missing decals.

■Dispose of hazardous waste properly.Examples of potentially hazardous waste are used motor oil, fuel and fuel filters.

■DO NOT use food or plastic containers to dispose of hazardous waste.

■DO NOT pour waste, oil or fuel directly onto the ground, down a drain or into any water source.

Emergencies

■ALWAYS know the location of the nearest fire extinguisher and first aid kit.

■In emergencies always know the location of the nearest phone or keep a phone on the job site. Also know the phone numbers of the nearest ambulance, doctor and fire department. This information will be invaluable in the case of an emergency.

PAGE 10 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Whiteman Series Concrete Mixers Page Heres HOW to GET Help WC-62P/S Concrete Mixer Table of Contents WC-62P/S Concrete Mixer Parts Ordering Procedures WC-62P/S Concrete Mixer Specifications Specifications Engines/Electric MotorWC-62P/S Concrete Mixer Dimensions Mixer WC-62P/S Concrete Mixer Safety Message Alert Symbols Foryour Safety and the Safety of OthersGeneral Safety WC-62P/S Concrete Mixer Rules for Safe OperationWC-62P/S Concrete Mixer Rules for Safe Operation EmergenciesWC-62P/S Concrete Mixer Operation and Safety Decals Machine Safety DecalsWC-62P/S Concrete Mixer General Information WC-62P/S Concrete Mixer Mixer Basic Components WC-62P/S Concrete Mixer Basic Engine Components Engine Controls and ComponentsAssembly Handwheel AssemblyTow Bar to Vehicle Connection Coupler Only Mixer Tow Bar Vehicle Connection Pintle and LoopWC-62P/S Concrete Mixer Safety Chain Connection Tow Bar to Mixer ConnectionElectric Motor Electric Motor Voltage Change SwitchWC-62P/S Concrete Mixer Electric Motor Electric Motor ConnectionSingle Phase Electric Motor with 12 inch Pigtail Cable WC-62P/S Concrete Mixer Electric MotorWC-62P/S Concrete Mixer PRE-INSPECTION GAS Engine WC-62P/S Concrete Mixer Initial START-UP GAS Engine Starting the Engine Gasoline OnlyInitial Start-up Instructions Electric Motor Starting WC-62P/S Concrete Mixer Initial START-UP Electric MotorStarting the Electric Motor Operation WC-62P/S Concrete Mixer OperationStopping the Mixer Electric WC-62P/S Concrete Mixer Maintenance Engine WC-62P/S Concrete Mixer Maintenance Engine MaintenanceWC-62P/S Concrete Mixer Maintenance Mixer WC-62P/S Concrete Mixer Maintenance Mixer Suspension ComponentsTo tighten wheel lug nuts Page WC-62P/S Concrete Mixer Troubleshooting Engine Engine TroubleshootingWC-62P/S Concrete Mixer Troubleshooting ENGINE/MIXER Engine TroubleshootingExplanation of Code in Remarks Column Items Found In the Remarks ColumnWC-62P/S Concrete Mixer Suggested Spare Parts Name Plate and Decals DECAL, Emergency Stop DECAL, Safety InstructionsMQ Whiteman Logo CIPDCL160 DECAL, Crush Warning DECAL, Towing InstructionsPlastic Barrel Assy NUT, Lock 3/8 NC HOUSING, JackshaftRing Gear PLUG, ExpansionSteel Barrel Assy Shim .187 Thick Housing JackshaftShim 0.25 Thick Shim .140 ThickMain Frame Assy WASHER, Lock 1/4 Connector LinkGUARD, Gear Wheel Dump GearAxle Assy Spring Leaf Lock NUT 5/8 NCSpring Support Axle 1-1/16 SpindleCabinet Assy WASHER, Flat 5/16 Rubber ProtectorCabinet Engine Assy Latch ASSY., CompleteGAS Engine Mounting Plate Assy ENGINE, Robin 8.5 HP ENGINE, Honda 5.5 HPENGINE, Honda 8.0 HP RING, RetainingElectric Motor Mounting Plate Assy Belt A45 MOTOR, Electric 1.5 HPUpper Pulley Large Drive Pulley SmallAIR Cleaner Assy GROMMET, AIR Cleaner ELEMENT, AIR CLEANER, DualCOVER, AIR Cleaner COLLAR, AIR CleanerCamshaft Assy ROD Push SPRING, Weight ReturnCamshaft ARM Valve RockerCarburetor Assy Valve SET, Float PLATE, Lever SettingGasket SET Float SETControl Assy SPRING, Governor ARM, GovernorROD, Governor SPRING, Throttle ReturnCrankcase Cover Assy PIN, Governor Weight WEIGHT, GovernorHOLDER, Governor Weight Type BalancerCrankshaft Assy Weight Balancer Cylinder Barrel Assy BOLT, Drain Plug Switch ASSY., OIL LevelSHAFT, Governor ARM Ring 14MM AraiCylinder Head Assy CLIP, Valve Guide GUIDE, VALVE, OS, OptionalGUIDE, EX. VALVE, OS, Optional GASKET, Cylinder HeadFAN Cover Assy CLIP, Tube Switch ASSY., Engine StopCLIP, Wire Harness ShroudFlywheel Assy NUT, Special 16MM FAN, CoolingFlywheel Comp KEY, Special WoodruffMuffler Assy PROTECTOR, EX. Pipe MufflerPROTECTOR, Muffler PIPE, EXFuel Tank Assy Tank COMP., Fuel *NH1*, Black Rubber Supporter 107MMJOINT, Fuel Tank GASKET, Fuel Filler CAPIgnition Coil Assy Coil ASSY., Ignition GROMMET, WireWIRE, Stop Switch 370MM CAP ASSY., Noise SuppressorPiston Assy Ring SET, PISTON, 0.75, Optional BOLT, Connecting RODRing SET, PISTON, STD PISTON, StandardRecoil Starter Assy SPRING, Friction PULLEY, Recoil StarterRATCHET, Starter SPRING, Starter ReturnGear Reduction Assy SHAFT, P.T.O. H- Type GEAR, Primary Drive 17TCountershaft Shim a OptionalLabel Assy MARK, CAUTION, External Labels AssyEMBLEM, Internal LABEL, CautionHonda GX160K1HX2 AIR Cleaner Assy Includes Items W/ # COVER, AIR Cleaner DualGASKET, Elbow Includes Items W NUT, CAP 6MMHonda GX160K1HX2 Camshaft Assy LIFTER, Valve ROD, PushARM, Valve Rocker PIVOT, Rocker ARMHonda GX160K1HX2 Carburetor Assy INSULATOR, Carburetor SN BE65B BSCREW, Throttle Stop SPACER, CarburetorHonda GX160K1HX2 Control Assy SPRING, Levr SPRING, Control AdjustingSpring Governor HOLDER, CableHonda GX160K1HX2 Crankcase Cover Assy PIN A, Dowel 8 X Honda GX160K1HX2 Crankshaft Assy CRANKSHAFT, Q- Type Honda GX160K1HX2 Cylinder Barrel Assy PIN, Lock 8MM WASHER, Thrust 6MMNUT, Flange 10MM BOLT, Flange 6 XHonda GX160K1HX2 Cylinder Head Assy TUBE, Breather GUIDE, Valve OS OptionalCOVER, Head BOLT, Flange 6Honda GX160K1HX2 FAN Cover Assy CLIP, Harness COVER, FAN NH1 BlackPLATE, Side OIL Alert SUB- HarnessHonda GX160K1HX2 Flywheel Assy FLYWHEEL, Lamp PULLEY, StarterFlywheel NUT, Special 14MMHonda GX160K1HX2 Fueltank Assy TANK, Fuel *NH1* Black RUBBER, Supporter 107MMTANK, Fuel *R8* Bright RED CLIP, Tube B8Honda GX160K1HX2 Ignition Coil Assy Coil ASSEMBLY, Ignition Honda GX160K1HX2 Muffler Assy ARRESTER, Spark Optional Muffler OptionalNUT, HEX MM Honda GX160K1HX2 Piston Assy Honda GX160K1HX2 Piston Assy Honda GX160K1HX2 Recoil Starter Assy GUIDE, Ratchet SCREW, SettingREEL, Recoil Starter SPRING, Recoil StarterHonda GX160K1HX2 Gear Reduction Assy COVER, Reduction Case ReductionGASKET, Reduction Case GASKET, Reduction CoverEngine Labels Assy MARK, Choke EnblemMARK, OIL Alert E Effective October 1, 2002 Terms and Conditions of Sale Parts Page Post Office BOX 6254 CARSON, CA

WC-62P, WC-62S specifications

Multiquip, a renowned name in the construction and industrial equipment sector, offers a range of high-performance concrete mixers. Among its impressive lineup are the WC-62S and WC-62P models. These versatile mixers are designed to cater to a variety of job site requirements, making them ideal for both small-scale and large-scale concrete projects.

The WC-62S model is a standout in many ways. It features a robust 6-cubic-foot mixing drum, allowing for efficient batch mixing and superior output. This mixer is equipped with a powerful Honda engine, which ensures reliable performance even in challenging conditions. One of its key characteristics is the heavy-duty steel construction that enhances durability, enabling it to withstand the wear and tear of daily use on the job site.

In terms of technology, the WC-62S incorporates a unique mixing action. The drum rotates in a clockwise direction during mixing, followed by a counterclockwise rotation for discharge. This dual-action mixing process guarantees a thorough blend of materials, resulting in a consistent concrete mix every time. Additionally, the model features a user-friendly control panel with easy-to-understand indicators, making operation straightforward for users of all skill levels.

On the other hand, the WC-62P model caters to similar needs but comes with distinct functionalities. It boasts a self-contained hydraulic system designed for enhanced mixing efficiency. This self-loading mixer can reduce labor costs and time on site, allowing for a quicker turnaround on projects. This model also features an adjustable discharge height, providing versatility when pouring concrete.

Both the WC-62S and WC-62P come equipped with safety features that prioritize user protection. These mixers include emergency stop buttons and rubberized grips to ensure that operators maintain a safe and secure hold throughout mixing tasks. Furthermore, the compact design of these mixers allows for easy transportation and storage, making them an excellent choice for contractors who require mobility.

Overall, the Multiquip WC-62S and WC-62P stand out thanks to their innovative features, durable construction, and operational efficiency. Whether it's for a small repair job or a large-scale construction project, these concrete mixers are designed to meet the demands of various applications. With their reliable performance and user-friendly design, Multiquip's WC-62S and WC-62P mixers continue to be preferred choices for contractors seeking quality and efficiency in their concrete mixing solutions.
Top Page Image Contents