Multiquip WC-62S manual WC-62P/S Concrete Mixer PRE-INSPECTION GAS Engine

Page 20

WC-62P/S CONCRETE MIXER — PRE-INSPECTION (GAS ENGINE)

Before Starting

1.Read safety instructions at the beginning of manual.

2.Clean the mixer, removing dirt and dust, particularly the engine cooling air inlet, carburetor and air cleaner.

3.Check the air filter for dirt and dust. If air filter is dirty, replace air filter with a new one as required.

Table 7. Oil Type

Season

Temperature

Oil Type

 

 

 

Summer

25°C or Higher

SAE 10W-30

 

 

 

Spring/Fall

25°C~10°C

SAE 10W-30/20

 

 

 

Winter

0°C or Lower

SAE 10W-10

 

 

 

4.Check carburetor for external dirt and dust. Clean with dry compressed air.

5.Check fastening nuts and bolts for tightness.

Engine Oil Check

1.To check the engine oil level, place the mixer on secure level ground with the engine stopped.

2.Remove the filler dipstick from the engine oil filler hole (Figure 8) and wipe it clean.

Figure 8. Engine Oil Dipstick (Removal)

3.Insert and remove the dipstick without screwing it into the filler neck. Check the oil level shown on the dipstick.

4.If the engine oil level is low (Figure 9), fill to the edge of the oil filler hole with the recommended oil type (Table 7). See Table 2 for the oil capacity of your type engine.

Figure 9. Engine Oil Dipstick (Oil Level)

Explosive Fuel

Fuel Check

If your mixer has a gasoline engine, determine if the engine fuel is low. If fuel is low, remove the fuel filler cap and fill with unleaded gasoline. Motor fuels are highly flammable and can be dangerous if mishandled. DO NOT smoke while refueling. DO NOT attempt to refuel the trowel if the engine is hot! or running.

1.Remove the gasoline cap located on top of fuel tank.

2.Visuallyinspecttoseeiffuellevelislow. Iffuelislow,replenish with unleaded fuel.

3.When refueling, be sure to use a strainer for filtration. DO NOT top-off fuel. Wipe up any spilled fuel.

V-belt Check

A worn or damaged V-belt can adversely affect the performance of the mixer. If a V-belt is defective or worn simply replace the V- belt as outlined in the maintenance section of this manual.

Blade Check

Check for worn blades. If using a steel tub and the blades are worn, replace the entire tub assembly. Remember the blades are welded to tub.

If using a plastic tub, replace the blades using the part numbers referenced in the parts section of this manual.

Start/Stop Switches

This mixer has been equipped with a start/stop switches for both the gasoline and electric motor mixers.These switches should be tested every time the engine or motor is started.

Grease Fittings (Zerk)

Check the zerk grease fittings (Figure 27) as shown in the maintenance section of this manual.These grease fittings lubricate the handwheel and the yoke mechanism.

PAGE 20 —WC-62P/S CONCRETE MIXERS — PARTS & OPERATION MANUAL — REV. #7 (06/30/05)

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Whiteman Series Concrete Mixers Page Heres HOW to GET Help WC-62P/S Concrete Mixer Table of Contents WC-62P/S Concrete Mixer Parts Ordering Procedures WC-62P/S Concrete Mixer Specifications Specifications Engines/Electric MotorWC-62P/S Concrete Mixer Dimensions Mixer WC-62P/S Concrete Mixer Safety Message Alert Symbols Foryour Safety and the Safety of OthersGeneral Safety WC-62P/S Concrete Mixer Rules for Safe OperationWC-62P/S Concrete Mixer Rules for Safe Operation EmergenciesWC-62P/S Concrete Mixer Operation and Safety Decals Machine Safety DecalsWC-62P/S Concrete Mixer General Information WC-62P/S Concrete Mixer Mixer Basic Components WC-62P/S Concrete Mixer Basic Engine Components Engine Controls and ComponentsAssembly Handwheel AssemblyTow Bar to Vehicle Connection Coupler Only Mixer Tow Bar Vehicle Connection Pintle and LoopWC-62P/S Concrete Mixer Safety Chain Connection Tow Bar to Mixer ConnectionElectric Motor Voltage Change Switch WC-62P/S Concrete Mixer Electric MotorElectric Motor Electric Motor ConnectionSingle Phase Electric Motor with 12 inch Pigtail Cable WC-62P/S Concrete Mixer Electric MotorWC-62P/S Concrete Mixer PRE-INSPECTION GAS Engine WC-62P/S Concrete Mixer Initial START-UP GAS Engine Starting the Engine Gasoline OnlyStarting the Electric Motor WC-62P/S Concrete Mixer Initial START-UP Electric MotorInitial Start-up Instructions Electric Motor Starting Stopping the Mixer Electric WC-62P/S Concrete Mixer OperationOperation WC-62P/S Concrete Mixer Maintenance Engine WC-62P/S Concrete Mixer Maintenance Engine MaintenanceWC-62P/S Concrete Mixer Maintenance Mixer WC-62P/S Concrete Mixer Maintenance Mixer Suspension ComponentsTo tighten wheel lug nuts Page WC-62P/S Concrete Mixer Troubleshooting Engine Engine TroubleshootingWC-62P/S Concrete Mixer Troubleshooting ENGINE/MIXER Engine TroubleshootingExplanation of Code in Remarks Column Items Found In the Remarks ColumnWC-62P/S Concrete Mixer Suggested Spare Parts Name Plate and Decals DECAL, Safety Instructions MQ Whiteman Logo CIPDCL160 DECAL, Crush WarningDECAL, Emergency Stop DECAL, Towing InstructionsPlastic Barrel Assy HOUSING, Jackshaft Ring GearNUT, Lock 3/8 NC PLUG, ExpansionSteel Barrel Assy Housing Jackshaft Shim 0.25 ThickShim .187 Thick Shim .140 ThickMain Frame Assy Connector Link GUARD, Gear WheelWASHER, Lock 1/4 Dump GearAxle Assy Lock NUT 5/8 NC Spring SupportSpring Leaf Axle 1-1/16 SpindleCabinet Assy Rubber Protector Cabinet Engine AssyWASHER, Flat 5/16 Latch ASSY., CompleteGAS Engine Mounting Plate Assy ENGINE, Honda 5.5 HP ENGINE, Honda 8.0 HPENGINE, Robin 8.5 HP RING, RetainingElectric Motor Mounting Plate Assy MOTOR, Electric 1.5 HP Upper Pulley LargeBelt A45 Drive Pulley SmallAIR Cleaner Assy ELEMENT, AIR CLEANER, Dual COVER, AIR CleanerGROMMET, AIR Cleaner COLLAR, AIR CleanerCamshaft Assy SPRING, Weight Return CamshaftROD Push ARM Valve RockerCarburetor Assy PLATE, Lever Setting Gasket SETValve SET, Float Float SETControl Assy ARM, Governor ROD, GovernorSPRING, Governor SPRING, Throttle ReturnCrankcase Cover Assy WEIGHT, Governor HOLDER, Governor WeightPIN, Governor Weight Type BalancerCrankshaft Assy Weight Balancer Cylinder Barrel Assy Switch ASSY., OIL Level SHAFT, Governor ARMBOLT, Drain Plug Ring 14MM AraiCylinder Head Assy GUIDE, VALVE, OS, Optional GUIDE, EX. VALVE, OS, OptionalCLIP, Valve Guide GASKET, Cylinder HeadFAN Cover Assy Switch ASSY., Engine Stop CLIP, Wire HarnessCLIP, Tube ShroudFlywheel Assy FAN, Cooling Flywheel CompNUT, Special 16MM KEY, Special WoodruffMuffler Assy Muffler PROTECTOR, MufflerPROTECTOR, EX. Pipe PIPE, EXFuel Tank Assy Rubber Supporter 107MM JOINT, Fuel TankTank COMP., Fuel *NH1*, Black GASKET, Fuel Filler CAPIgnition Coil Assy GROMMET, Wire WIRE, Stop Switch 370MMCoil ASSY., Ignition CAP ASSY., Noise SuppressorPiston Assy BOLT, Connecting ROD Ring SET, PISTON, STDRing SET, PISTON, 0.75, Optional PISTON, StandardRecoil Starter Assy PULLEY, Recoil Starter RATCHET, StarterSPRING, Friction SPRING, Starter ReturnGear Reduction Assy GEAR, Primary Drive 17T CountershaftSHAFT, P.T.O. H- Type Shim a OptionalLabel Assy Labels Assy EMBLEM, InternalMARK, CAUTION, External LABEL, CautionHonda GX160K1HX2 AIR Cleaner Assy COVER, AIR Cleaner Dual GASKET, Elbow Includes Items WIncludes Items W/ # NUT, CAP 6MMHonda GX160K1HX2 Camshaft Assy ROD, Push ARM, Valve RockerLIFTER, Valve PIVOT, Rocker ARMHonda GX160K1HX2 Carburetor Assy SN BE65B B SCREW, Throttle StopINSULATOR, Carburetor SPACER, CarburetorHonda GX160K1HX2 Control Assy SPRING, Control Adjusting Spring GovernorSPRING, Levr HOLDER, CableHonda GX160K1HX2 Crankcase Cover Assy PIN A, Dowel 8 X Honda GX160K1HX2 Crankshaft Assy CRANKSHAFT, Q- Type Honda GX160K1HX2 Cylinder Barrel Assy WASHER, Thrust 6MM NUT, Flange 10MMPIN, Lock 8MM BOLT, Flange 6 XHonda GX160K1HX2 Cylinder Head Assy GUIDE, Valve OS Optional COVER, HeadTUBE, Breather BOLT, Flange 6Honda GX160K1HX2 FAN Cover Assy COVER, FAN NH1 Black PLATE, Side OIL AlertCLIP, Harness SUB- HarnessHonda GX160K1HX2 Flywheel Assy PULLEY, Starter FlywheelFLYWHEEL, Lamp NUT, Special 14MMHonda GX160K1HX2 Fueltank Assy RUBBER, Supporter 107MM TANK, Fuel *R8* Bright REDTANK, Fuel *NH1* Black CLIP, Tube B8Honda GX160K1HX2 Ignition Coil Assy Coil ASSEMBLY, Ignition Honda GX160K1HX2 Muffler Assy NUT, HEX MM Muffler OptionalARRESTER, Spark Optional Honda GX160K1HX2 Piston Assy Honda GX160K1HX2 Piston Assy Honda GX160K1HX2 Recoil Starter Assy SCREW, Setting REEL, Recoil StarterGUIDE, Ratchet SPRING, Recoil StarterHonda GX160K1HX2 Gear Reduction Assy Case Reduction GASKET, Reduction CaseCOVER, Reduction GASKET, Reduction CoverEngine Labels Assy MARK, OIL Alert E EnblemMARK, Choke Effective October 1, 2002 Terms and Conditions of Sale Parts Page Post Office BOX 6254 CARSON, CA

WC-62P, WC-62S specifications

Multiquip, a renowned name in the construction and industrial equipment sector, offers a range of high-performance concrete mixers. Among its impressive lineup are the WC-62S and WC-62P models. These versatile mixers are designed to cater to a variety of job site requirements, making them ideal for both small-scale and large-scale concrete projects.

The WC-62S model is a standout in many ways. It features a robust 6-cubic-foot mixing drum, allowing for efficient batch mixing and superior output. This mixer is equipped with a powerful Honda engine, which ensures reliable performance even in challenging conditions. One of its key characteristics is the heavy-duty steel construction that enhances durability, enabling it to withstand the wear and tear of daily use on the job site.

In terms of technology, the WC-62S incorporates a unique mixing action. The drum rotates in a clockwise direction during mixing, followed by a counterclockwise rotation for discharge. This dual-action mixing process guarantees a thorough blend of materials, resulting in a consistent concrete mix every time. Additionally, the model features a user-friendly control panel with easy-to-understand indicators, making operation straightforward for users of all skill levels.

On the other hand, the WC-62P model caters to similar needs but comes with distinct functionalities. It boasts a self-contained hydraulic system designed for enhanced mixing efficiency. This self-loading mixer can reduce labor costs and time on site, allowing for a quicker turnaround on projects. This model also features an adjustable discharge height, providing versatility when pouring concrete.

Both the WC-62S and WC-62P come equipped with safety features that prioritize user protection. These mixers include emergency stop buttons and rubberized grips to ensure that operators maintain a safe and secure hold throughout mixing tasks. Furthermore, the compact design of these mixers allows for easy transportation and storage, making them an excellent choice for contractors who require mobility.

Overall, the Multiquip WC-62S and WC-62P stand out thanks to their innovative features, durable construction, and operational efficiency. Whether it's for a small repair job or a large-scale construction project, these concrete mixers are designed to meet the demands of various applications. With their reliable performance and user-friendly design, Multiquip's WC-62S and WC-62P mixers continue to be preferred choices for contractors seeking quality and efficiency in their concrete mixing solutions.
Top Page Image Contents