Peavey MP 600 manual Speaker Connections, Channel 1- 6 Features

Page 5

SPEAKER CONNECTIONS

This section will help you locate the two speaker output jacks on the rear of your MP 600. Though there are two output jacks, they are mono (parallel) and not stereo. (2 — 8 ohms speakers)

WARNING: NEVER ALLOW YOUR TOTAL SPEAKER IMPEDANCE TO DROP BELOW THE INDICATED MINIMUM IMPEDANCE.

4.SPEAKER OUTPUTS

Two parallel 1/4" jacks are provided at the output of the power amplifier. Minimum speaker

impedance (minimum load) is 4 ohms.

.

CHANNEL (1— 6) FEATURES

The following section describes Channels 1 — 6. Each of these input channels are identical. Some features listed below can be found on Channel 7 as well.

5.MIC INPUT

 

XLR balanced low impedance channel input optimized for a

 

microphone or other low impedance source. Pin 2 is the positive

10

input. This connector has +15V phantom power supply on pins 2

 

and 3 at all times. (Pin 1 is the ground reference.)

9

8

7

6

5

WARNING: SOME PRODUCTS, INCLUDING SOME WIRELESS MICROPHONE UNITS, CAN BE DAMAGED BY PHANTOM POWER. CHECK THE OPERATING INSTRUCTIONS OF THE PRODUCT YOU WISH TO CONNECT TO THE MIC INPUT BEFORE CONNECTING. PHANTOM POWER DOESN’T AFFECT LOW IMPEDANCE DYNAMIC MICROPHONES.

6.LINE INPUT

1/4" unbalanced input that accepts line level sources equipped with a 1/4" plug (TS). The two inputs (XLR and 1/4") cannot be used simultaneously.

7.GAIN

Sets the level of the individual channel in the mix.

8.REVERB

Sets the level to internal reverb from channel and must be

used in conjunction with the master reverb level. It is post gain and will be affected by the Gain adjustment (7). The Reverb control also determines the level of signal sent to the Effects Output (14).

9.LOW EQ

A shelving type of active tone control that varies the bass frequency levels ±15 dB at 100 Hz. It will add depth to thin signals, or clean up muddy ones.

10.HIGH EQ

A shelving type of active tone control that varies the treble frequency level ±15 dB at 10 kHz. It is designed to remove noise or to add brilliance to the signal, depending on the quality of the source.

5

Image 5
Contents W e r e d M i x e r Page Features Powered MixerPower Switch Rear Panel PowerRemovable AC Power Cord FuseSpeaker Connections Channel 1- 6 FeaturesMaster Features Channel Seven FeaturesLine and Tape Inputs Tape REC OutputsPower LED Reverb FootswitchEffects Output Main OutputChannel SpecificationsLevel Diagram Hook UP Diagram Características Mezcladora AmplificadaRear Panel Poder Switch DE PoderConexiones DE Bocinas FusibleSalidas DE Bocinas POWER. Revisa LOS Instructivos DE CualquierCaracterísticas DE LOS Canales Entrada DE MicroCaracterísticas DEL Canal Siete Características MaestrasEntradas DE Línea Y Cinta Salidas DE Cinta RECSalida DE Efectos Control DE Pedal DE ReverbSalida Maestra Main Control Maestro DE Nivel DE ReverbCanal EspecificacionesCaracteristiques Mixeur AmplifieSorties HAUT-PARLEUR Rear Panel AlimentationConnexions DES HAUT-PARLEURS Entree Micro Canaux 1 aEntree Line ReverbeSection Master CanalControle DE Reverbe Master Sortie MainLED D’ALIMENTATION Equalisation MasterResidual Funktionen Power MixerFuse Gerätesicherung Rear Panel Power NetzanschlussSpeaker Connections Lautsprecheranschlüsse MIC Input MIC-EINGANG Kanal 1 6 FunktionenSpeaker Outputs Lautsprecherausgänge Master Funktionen Funktionen DES Kanal SiebenLine UND Tape Inputs LINE- UND TAPE-EINGÄNGE Tape REC Output Tape REC -AUSGÄNGEEffekte Output EFFEKTE-AUSGANG Reverb Footswitch Reverb FussschalterMain Output MAIN-AUSGANG Master Equalization MASTER-EQUALIZERKanal SpezifikationenPage Important Safety Instructions Peavey Electronics Corporation Limited Warranty