Lexicon CP-3 owner manual Music

Page 47

Using

the CP-3

Lexicon

Music

*OFF if configured with no center speaker

**BYPASS if center speaker configured as NONE or FULL; 63 Hz if configured as SMALL (Presets only)

EFFECT LEVEL controls the loudness of the center, side and rear outputs.

CENTER LEVEL attenuates the level of the center channel and can turn it off completely. The proper setting for this control will vary depending on the recording and your taste. There is no "correct" setting.

CENTER DELAY provides a delay of the center channel. When the center speaker is closer to the central listening position than the main left and right speakers, the sound from it will arrive at the listener just slightly ahead of the sound from the main left and right speakers. Depending on your speakers and your room, adjustment with this control can be dramatic, or quite subtle. Adjustment will be easiest with CENTER LEVEL set to Maximum, listening to music with a strongly centered vocalist. Listen for tight localization and a smooth blend between the three front speakers.

SIDE LEVEL controls the volume level of the side speakers. Since Music Surround is a dynamic ambience extraction mode, the effect of the side speakers will depend on the recording. Although the default value is 0, the correct setting will vary with each recording, your room, and your personal taste.

SURROUND EFFECT allows you to optimize the Music Surround mode for music listening or for films. When set to FILM, the Auto Azimuth Error Correction, Rear Dolby B and rear steering are all turned ON. When set to MUSIC, they are all turned OFF.

BASS SPLIT takes the low bass from the center, where it is in many film and music mixes, and distributes it instead to the left and right front-channel speakers. Bass Splitting is valuable because in many video installations the center speaker is smaller than the two main stereo speakers and is less capable of handling the lowest frequencies. By directing the low frequencies to the main speakers, there is less risk of damage to a small center speaker and no loss of bass information since it will be reproduced by the main speakers.

44

Page 46 Page 48
Image 47
Page 46 Page 48
Contents CP-3 Acknowledgements PrecautionsUnpacking and Inspection Safety Suggestions CP-3 Digital Surround Processor Contents Introduction Introduction to the CP-3 Using the Documentation Glossary of Terms Finding your way around System OverviewIntroduction to the CP-3 Input Controls Indicators Front PanelRear Panel Power On/OffOn/Off Standard RemoteModes Expanded RemoteRefer to the Expanded Remote AC Connections ConnectionAudio/Video Cables Speaker Connections Wiring ConsiderationsWire Lengths Length AWG Size & StrandingAudio/Video Connections Connecting the CP-3 as a preamp Connecting the CP-3 in a Tape Monitor Loop Video Connections D C O N T R a S T Calibration LCD AdjustmentP U T S S P L a Y M E N U O S D P O S I T I O NVideo On-Screen Display Calibration Setting the Speaker Configuration Adjusting Input Parameters Setting Input Levels+ , . / 0-9 A-Z Loading Automatic Input ModeSignal-to-Noise Optimization Auto-Mode LoadPAL and Secam Setting Output LevelsCalibration Calibrating the Listener Position Calibrate Noise Calibrate Left only Setting Rear Delay Settings Lock OFF Customization Locking In Settings Custom NameCustom Modes Mode Loads register Default presetStore Menu Store this Mode SET Mode Name Renaming a mode Presets and User Registers Using the ModesPanorama Parameters Using CP-3Using CP-3 Ambience Parameters AmbienceUsing CP-3 Reverb Parameters Using CP-3 Surround Parameters Television SurroundUsing CP-3 Music Full Range Mono Logic Pro Logic THX Cinema Problem Possible Cause and Solution TroubleshootingPossible Cause and Solution ProblemRestore Mode Setup to Exit Routine Maintenance Restoring DefaultsInstallation Documentation Lexicon Display Time AC Power wiring notesInput OSD PositionSpecifications Lexicon, Inc Oak Park Bedford, MA Tel Fax

CP-3 specifications

The Lexicon CP-3 is a high-performance audio processor known for its exceptional sound quality and advanced features, making it a preferred choice for audiophiles and sound professionals alike. This preamplifier and audio processor delivers a remarkable listening experience, incorporating cutting-edge technologies and sophisticated design.

One of the standout features of the CP-3 is its multi-channel processing capability. With support for various audio formats, it provides an immersive surround sound experience, making it a perfect fit for home theaters and high-end audio setups. The processor boasts a robust array of inputs and outputs, ensuring compatibility with a wide range of audio equipment and allowing seamless integration into existing systems.

The Lexicon CP-3 employs proprietary technologies, such as the acclaimed Lexicon Digital Signal Processing (DSP), which delivers pristine audio reproduction with minimal distortion. This technology, combined with high-resolution audio processing, ensures that every nuance of the source material is preserved. The processor also supports various audio formats, including Dolby Atmos and DTS:X, which enhances the spatial dimension of audio playback.

Another significant aspect of the CP-3 is its user-friendly interface. The processor features an intuitive control panel and a well-organized menu system, allowing users to access and configure settings with ease. Additionally, it is equipped with a remote control for convenient operation, providing flexibility for users who prefer to adjust settings from a distance.

The build quality of the Lexicon CP-3 is impressive, reflecting the brand's commitment to durability and longevity. The chassis is designed to minimize interference and provide optimal shielding against electromagnetic noise. This attention to detail contributes to the overall sound quality, ensuring that users receive the best possible audio experience.

Furthermore, the CP-3 includes advanced room correction technologies that help calibrate the sound output based on the characteristics of the listening environment. This feature optimizes the audio performance, eliminating potential issues caused by room acoustics and providing listeners with a balanced and natural sound.

In conclusion, the Lexicon CP-3 is a versatile and powerful audio processor that excels in delivering high-fidelity sound. With its multi-channel processing capabilities, innovative technologies, user-friendly design, and commitment to quality, it stands as a formidable choice for both casual listeners and discerning audiophiles, enhancing any audio setup to new heights.
Top Page Image Contents