Huawei ME909 Audio Interface, Pin Pin Name Description DC Characteristics Min Typ, PCM clock

Page 21

HUAWEI ME909 Series Mini PCIe Module

 

Hardware Guide

Description of the Application Interfaces

To meet the requirements of 3GPP TS 51.010-1 protocols and electromagnetic compatibility (EMC) authentication, the USIM socket should be placed near the PCIe interface (it is recommended that the PCB circuit connects the PCIe interface and the USIM socket does not exceed 100 mm), because a long circuit may lead to wave distortion, thus affecting signal quality.

It is recommended that you wrap the area adjacent to the UIM_CLK and

UIM_DATA signal wires with ground. The Ground pin of the USIM socket and the Ground pin of the USIM card must be well connected to the power Ground pin supplying power to the PCIe Adapter.

A 100 nF capacitor and1 μF capacitor are placed between the UIM_PWR and GND pins in a parallel manner (If UIM_PWR circuit is too long, that the larger capacitance such as 4.7 μF can be employed if necessary). Three 33 pF capacitors are placed between the UIM_DATA and Ground pins, the UIM_RESET and Ground pins, and the UIM_CLK and Ground pins in parallel to filter interference from RF signals.

It is recommended to take electrostatic discharge (ESD) protection measures near the USIM card socket. The TVS diode with Vrwm of 5 V and junction capacitance less than 10 pF must be placed as close as possible to the USIM socket, and the Ground pin of the ESD protection component is well connected to the power Ground pin that supplies power to the PCIe Adapter.

3.11Audio Interface

The ME909 module provides one PCM digital audio interface. Table‎ 3-5lists the signals on the digital audio interface.

The software feature of PCM is planning.

Table 3-5Signals on the digital audio interface

Pin

Pin Name

I/O

Description

DC Characteristics (V)

No.

 

 

 

Min.

Typ.

Max.

 

 

 

 

45

PCM_CLK

O

PCM clock

–0.3

1.8

2.1

 

 

 

 

 

 

 

49

PCM_DIN

I

PCM data input

–0.3

1.8

2.1

 

 

 

 

 

 

 

51

PCM_SYNC

O

PCM interface sync

–0.3

1.8

2.1

 

 

 

 

 

 

 

47

PCM_DOUT

O

PCM data output

–0.3

1.8

2.1

The ME909 module interface enables communication with an external codec to support linear format.

 

Huawei Proprietary and Confidential

21

Issue 0.1 (2013-06-09)

Copyright © Huawei Technologies Co., Ltd.

 

Image 21
Contents Hardware Guide Issue DateNo Warranty About This Document Revision HistoryDocument Date Chapter Descriptions Version Contents Certifications FCC Statement Introduction 1ME909 series product nameProduct name Description State Overall Description Feature DescriptionAbout This Chapter Function OverviewLEDWWAN# Active-low LED signal indicating the state Circuit Block DiagramMini PCIe Interface Description of the Application InterfacesVCC3V3 WAKE#COEX1 GNDWDISABLE# UimresetUimpwr UimdataSmbdata SmbclkUsbd Usbdm USBD+ UsbdpPin No Pin Name Minimum Typical Maximum Power Sources and GroundsPower Valid to USB + high Power Supply Time SequenceCutting off 3.3 V will power off the module Parameter Remarks Time Nominal value UnitResinn Signal WAKE# Signal6Reset pulse timing WDISABLE# Signal LEDWWAN# SignalUSB Interface Pin Pin Name Description DC Characteristics Min Typ Max Pin No Pin Name Description DC Characteristics Min Typ MaxUsim Card Interface OverviewExternal 2.85 Usim card Circuit Recommended for the Usim Card InterfaceAudio Interface Pin Pin Name Description DC Characteristics Min TypPCM clock PCM data inputRF Antenna Connector NC Pins Reserved PinsPin No Pin Name Description Reserved Reserved, please keep openNC pins RF Specifications Operating FrequenciesOperating Band Conducted RF Measurement Conducted Rx Sensitivity and Tx PowerTest Environment Test StandardsBand Typical TBDType Value Modulation RB Allocation MPRdB Conducted Transmit PowerQpsk 16QAMAntenna Design Requirements Antenna Design IndicatorsPolarization 3 GSM/WCDMA/GPS Antenna Requirements InterferenceFrequency range Radio Test EnvironmentOperator, the customer must use the most suitable Antenna for that/those bandsPassive Tests Symbol Specification Min Max Unit Electrical and Reliability FeaturesExternal power voltage Digital input voltage Absolute RatingsElectrical Features of Usim Operating and Storage Temperatures and HumidityElectrical Features of Application Interfaces Specification Min Max UnitInput Power Supply Power Supply FeaturesPower Module Peak GSM Normal Normal LTE Slot Parameter Min Typ Max Ripple UnitDescription Bands Test Value Units Power ConsumptionDescription Band Test Value Units Power dBm WcdmaHsdpa 23dBm Tx Power IMT2100LTE Description Test Value Units ConfigurationGPRS850 TBD GPRS900 TBDDescription Max Test Value Units Configuration EDGE850 TBDEDGE900 TBD Test Condition Standard Reliability Features− UIM − USB EMC and ESD FeaturesHuawei Proprietary and Confidential Issue 0.1 Dimensions and Interfaces Mechanical Specifications1Dimensions of the ME909 module Dimensions of the Mini PCI Express ConnectorInstalling the Mini PCIe Adapter on the Main Board Specification Selection for FastenersHuawei Proprietary and Confidential Issue 0.1 Removing the Mini PCIe Adapter from the Main Board Page Certifications CertificationsCertification Model name ME909u-521 GCF WeeeInterference Safety InformationMedical Device Area with Inflammables and ExplosivesTraffic Security Safety of ChildrenAirline Security Environment ProtectionLaws and Regulations Observance Care and MaintenanceEmergency Call Regulatory InformationFCC Statement Appendix a Circuit of Typical Interface Acronym or Abbreviation Expansion Appendix B Acronyms and AbbreviationsHsupa HSPA+ISO LCP
Related manuals
Manual 13 pages 25.55 Kb