Enviro 50-1628 owner manual Optional Blower Fan Installation

Page 22

Initial Installation

INSTALLATION OF OPTIONAL BLOWER:

Figure 36: Optional Blower (Fan) Installation.

1.Remove the pre-assembled blower from the packaging. Inspect the blower for damage. If damage is noticed call your dealer, distributor or courier company and have components replaced.

2.Remove the side panel by pulling the panel up, slide the panel out of the bottom slots, and set aside.

3.Install the temperature sensor into the holder.

IMPORTANT: The temperature sensor must be in contact with the firebox.

4.Open the pedestal door and remove the four (4) T-20 screws holding the Control Panel in place.

5.Fit the Fan Unit into the cabinet being careful to work around the gas and pilot lines. The fan will fit up behind the gas valve. With an extension driver, fasten the Fan Unit in place with four (4) T-20 screws provided.

6.Install the Fan Controller into the provision in the Control Panel.

7.Install the Strain Relief plate into the stove back by fitting the tab on the plate into the stove back and secure the plate with a T-20 screw provided.

8.Plug in all the electrical connections as indicated in Figure 35. This includes the Fan Controller, Temperature sensor and Fan Unit.

9.Using the provided T-20 screw, located on the right mount below and behind the Temperature Sensor, fasten the wire tie supplied. With the wire tie capture the fan wires including the temperature switch wires, this will secure the wires and route them away from hot surfaces and out of the way of the fan blades

10.Re-install the Control Panel and Side Panel.

11.Plug the fan assembly into the wall outlet and turn the unit on to ensure fan operation.

22

Image 22
Contents Cara DR Safety Precautions GeneralTable of Contents Vented GAS Fireplace Heater Cara DR DV NG/LPG Codes And ApprovalsThis Enviro Cara DR Fireplace Specifications Cara DR Exterior DimensionsFor Your Safety Read Before Operating Operating InstructionsCara Component Sound & Reason Maintenance And Service Pilot FlameNo substitute materials are allowed Check burner for proper operation Kit Parts List Conversion Kit InstallationOpen Flame When Testing for Leaks Initial Installation Qualified Installers onlyManufacturer Trade Name Nominal Sizes Vent Termination Restrictions 51mm at top, 11⁄2 38mm at sides, 11⁄2 38mm at bottom Twist-LockThimble Wall Surface Attach With Installation for Cara DR Manifold Pressure Venturi SettingNatural Gas Propane Main Burner Min. Manifold PressureCanadian Installations Wire Size Max. LengthA. Installations Optional Blower Fan Installation Keep Clear of ALL Obstructions Initial Installation Secondary Installation Log Placement of Rear Log ChunksLog Placement of Left Log Remove door to clean glass Addition the seven 7 small rocks. These can be To clean glass Trouble Shooting Problem Possible Cause SolutionParts List Reference Part Description Part NumberParts List Parts Diagram Warranty To the DealerWarranty Warranty Installation Data Sheet
Related manuals
Manual 35 pages 39.8 Kb

50-1628 specifications

Enviro 50-1628 is a revolutionary piece of technology designed to enhance sustainability and efficiency in various applications, particularly in the field of environmental management. This advanced system focuses on achieving ecological balance while delivering high performance, making it a valuable asset for industries aiming for greener operations.

One of the main features of the Enviro 50-1628 is its cutting-edge filtration technology. The system utilizes multi-stage filtering mechanisms that purify air and water, effectively removing pollutants and contaminants. This is accomplished through a combination of mechanical, chemical, and biological processes, ensuring that the output meets or exceeds regulatory standards. The efficiency of the filtration system plays a crucial role in reducing environmental impact by minimizing harmful emissions and discharges.

Another notable characteristic of the Enviro 50-1628 is its intelligent monitoring capabilities. Equipped with advanced sensors, the system continuously collects data on environmental parameters such as air quality, temperature, and humidity. This real-time data is processed through sophisticated algorithms, enabling proactive adjustments to optimize system performance. This not only improves the efficiency of operations but also allows for timely interventions to prevent potential environmental hazards.

In terms of energy efficiency, the Enviro 50-1628 is designed with sustainability in mind. It incorporates renewable energy sources, such as solar panels, to power its systems, significantly reducing dependency on fossil fuels. Moreover, its modular design allows for easy scalability, enabling facilities to expand their capacity while maintaining energy efficiency and reducing carbon footprints.

The Enviro 50-1628 is also user-friendly, featuring an intuitive interface that allows operators to easily monitor and control various functions. This accessibility is crucial for promoting best practices in environmental management, ensuring that organizations can effectively implement and adhere to sustainability initiatives.

Furthermore, the Enviro 50-1628 is built with durability in mind, utilizing high-quality materials to ensure long-lasting performance even in demanding environments. This resilience not only extends the lifespan of the system but also reduces maintenance costs, making it a cost-effective solution for businesses committed to sustainable practices.

In summary, the Enviro 50-1628 stands out as a powerful tool in the pursuit of environmental sustainability. Its advanced filtration technology, intelligent monitoring systems, energy efficiency, user-friendly interface, and durable construction make it an excellent choice for industries looking to minimize their ecological footprint while maximizing operational efficiency. By integrating such technologies, organizations can take significant strides towards a greener future.