Trouble Shooting, Problem Possible Cause Solution

Trouble Shooting

Problem	Possible Cause	Solution

The main burner does not	The gas valve may not be on.	• Check that the gas control knob is in the “ON” position.
ignite when called for.
ignite when called for.	Thermostat is not calling for	• Adjust the thermostat several degrees above ambient
	Thermostat is not calling for	• Adjust the thermostat several degrees above ambient
	heat.	temperature.

	Problem with gas valve.	• Use a DC voltmeter to measure the voltage across the
		TPTH and TP terminals. Main operator voltage: Open
		circuit ≥ 325mV Closed circuit ≥ 100mV
		• If voltage is not present, check the control circuit for
		proper operation.
		• If proper control system voltage is present, replace the
		gas control.

Spark will not light the pilot	Defective piezo ignitor.	• Check connections to ignitor.
after repeatedly pressing the		• If ignitor connections are good but no spark, replace
spark ignitor.		ignitor.

	Broken spark electrode.	• Check for broken ceramic insulation, replace electrode if
		broken.

	Misaligned spark electrode.	• If spark is not arcing from electrode to pilot, loosen the
		screws on the pilot base adjust and tighten.

Pilot will not remain lit.	Problem with thermocouple	• Check for proper connection of the thermocouple to the
	circuit.	rear of the valve. If loose, fully tighten.
		• Check pilot for full flame impingement around
		thermocouple. If flame is too small, check gas pressure,
		adjust pilot rate screw, check pilot head for damage.
		• Check thermocouple voltage at valve. It must be greater
		than 5 mV. If low, replace thermocouple.

	Air in gas line (pilot dies while	• Bleed line.
	knob is depressed).	• Check gas line pressure.
		• Contact dealer.

Burners will not remain lit.	Problem with thermopile	• Check gas line pressure .
	circuit.	• Check for flame impingement on thermopile. If low, see
		“Pilot will not remain lit”.
		• Check thermopile for minimum of 300 mV when burner is
		switched on.
		• Check wiring to thermostat for breaks.

Flame lifting	Leak in vent pipe	• Check for leaks in vent connections.

	Improper vent configuration	• Check vent configuration with manual.

	Terminal may be recirculating	• Check to see if terminal is on correctly.
	flue gases	• May need to install high wind termination cap.
		• Contact dealer.

Glass fogs up	Normal Condition: after the appliance warms up the glass will clear.
	Due to additives in gas, glass may get hazy during operation Clean as needed.

Blue Flames	Normal during start up: flames will yellow as the fireplace heats up.

Flames are burning “dirty” or	Flame impingement	• Check log positioning.
sooting		• Increase primary air by opening the venturi shutter and/
		or by opening the vent restrictor.
		See also “Burners will not remain lit.”

Remote control doesn’t work	Problem with the remote	• One or more of the batteries are dead. See remote
		control instructions.

	Problem with fireplace	• The on/off switch is turned to OFF.
		• The gas control valve is turned to PILOT or OFF.
		• The pilot has gone out.

50-1628 specifications

Enviro 50-1628 is a revolutionary piece of technology designed to enhance sustainability and efficiency in various applications, particularly in the field of environmental management. This advanced system focuses on achieving ecological balance while delivering high performance, making it a valuable asset for industries aiming for greener operations.

One of the main features of the Enviro 50-1628 is its cutting-edge filtration technology. The system utilizes multi-stage filtering mechanisms that purify air and water, effectively removing pollutants and contaminants. This is accomplished through a combination of mechanical, chemical, and biological processes, ensuring that the output meets or exceeds regulatory standards. The efficiency of the filtration system plays a crucial role in reducing environmental impact by minimizing harmful emissions and discharges.

Another notable characteristic of the Enviro 50-1628 is its intelligent monitoring capabilities. Equipped with advanced sensors, the system continuously collects data on environmental parameters such as air quality, temperature, and humidity. This real-time data is processed through sophisticated algorithms, enabling proactive adjustments to optimize system performance. This not only improves the efficiency of operations but also allows for timely interventions to prevent potential environmental hazards.

In terms of energy efficiency, the Enviro 50-1628 is designed with sustainability in mind. It incorporates renewable energy sources, such as solar panels, to power its systems, significantly reducing dependency on fossil fuels. Moreover, its modular design allows for easy scalability, enabling facilities to expand their capacity while maintaining energy efficiency and reducing carbon footprints.

The Enviro 50-1628 is also user-friendly, featuring an intuitive interface that allows operators to easily monitor and control various functions. This accessibility is crucial for promoting best practices in environmental management, ensuring that organizations can effectively implement and adhere to sustainability initiatives.

Furthermore, the Enviro 50-1628 is built with durability in mind, utilizing high-quality materials to ensure long-lasting performance even in demanding environments. This resilience not only extends the lifespan of the system but also reduces maintenance costs, making it a cost-effective solution for businesses committed to sustainable practices.

In summary, the Enviro 50-1628 stands out as a powerful tool in the pursuit of environmental sustainability. Its advanced filtration technology, intelligent monitoring systems, energy efficiency, user-friendly interface, and durable construction make it an excellent choice for industries looking to minimize their ecological footprint while maximizing operational efficiency. By integrating such technologies, organizations can take significant strides towards a greener future.