Hearth and Home Technologies HST-42D owner manual 10-7/8 276 mm

Page 46

15-3/4 in.

(400 mm)

TR344 Round Termination Cap

34-3/4 in.

(883 mm)

32-1/2 in.

(826 mm)

TR342 Round Telescoping Termination Cap

23 in. (584 mm)

19 in.

(483 mm)

15-5/8 in.

(397 mm)

ST375 Square Termination Cap

13-1/4 in.

(337 mm)

16-1/4 in.

(413 mm)

22 in.

(559 mm)

23-1/8 in.

(587 mm)

18 in. (457 mm)

TS345/TS345P Square Termination Cap

20in.

(508 mm)

17 in.
(432 mm)
9-3/8 in.
(238 mm)
9-1/4 in.
(235 mm)
TCT375 Terra Cotta Cap
72 in.	36 in.
(1829 mm)	(914 mm)

10-7/8 in.

(276 mm)

2 in. (51 mm)

CT35 Chase Top

	C
	D					B
						B
			A
	LDS33/LDS46 Decorative Shroud
		A		B		C		D
Catalog #	in.	mm	in.	mm	in.	mm	in.	mm
LDS33	36	914	36	914	8-1/2	216	11	279
LDS46	48	1219	72	1829	8-1/2	216	11	279
						E
						D
				C
				B
						A
		LDS-BV Decorative Shroud
Catalog #			A	B	C	D	E
LDS-BV		in.	26	12-1/2	15-1/2	22	23
LDS-BV		mm	660	318	394	533	584
		mm	660	318	394	533	584

46	Heat & Glo • HST-42D • 27177 • Rev AB • 11/08

Image 46

Contents Hot screen/mesh and glass doors will cause burns Wood Burning FireplaceFire Risk Grate Listing Label Information/LocationNumber Installer Guide Table of ContentsUser Guide Warranty Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHeat & Glo HST-42D 27177 Rev AB 11/08 Non-Combustible Materials Listing and Code ApprovalsAppliance Certiﬁcation Combustible MaterialsYour Fireplace Operating InstructionsHot glass will cause burns Grate Seasoned WoodStarting a Fire FirescreenVented Gas Log Sets & Gas Log Lighters Glass DoorsOutside Air optional Optional ComponentsWood Fuel Disposal of Ashes Maintainance and ServiceChimney Inspection/Cleaning Creosote Formation and Need for RemovalInspect Grate Glass CleaningCheck Firebox Refractory Frequency As desiredTroubleshooting Guide Start Fire Problems Possible Cause SolutionGetting Started Typical Fireplace SystemDraft Design and Installation ConsiderationsNegative Pressure Locating Fireplace & Chimney Frequently open doors Central heat outlets or returnsFireplace System Requirements Tools and Supplies NeededInspect Fireplace and Components Framing & Clearances Select Fireplace LocationClearances Clearances to Combustible MaterialsSidewalls/Surrounds Frame the FireplacePosition the Fireplace Installation of FireplaceThings to Consider Place Protective Metal Hearth StripsFt min. from top of uppermost chimney section to air inlet Install Outside Air Kit AK14/AK18 InstallationChimney Assembly Chimney Requirements MetersUsing Offsets/Returns ExampleInstall Chimney Air Kit Assemble Chimney SectionsInstall Ceiling Firestops Installing the Ceiling FirestopInstall Attic Insulation Shield Prepare Attic Insulation ShieldFollowing steps should be skipped if using a chase Complete InstallationInstall Flashing Cut out Hole in RoofChimney Termination Requirements Flat RoofsChase Installations Construct the ChaseInstall Fireplace & Chimney Install Chase TopInstall Termination Cap ST375 Square Termination CapTS345/TS345P Square Termination Cap Field Constructed Shrouds ShroudsRadiation Shield Open Top Shroud TR342 caps require radiation shieldMailbox Style Shroud radiation shield required Roofed Style Shroud radiation shield requiredHearth Extension Finishing= 1/k x inches of thickness Finishing Material Noncombustible FacingCombustible Mantel Clearances to Mantels or other Combustibles above FireplaceSquares Wood Burning Inserts AccessoriesGas Log/Lighter Provision Gas Code, Ansi Z223.1Fireplace Dimensions Reference MaterialsChimney Components Catalog #14-1/2 10-7/8 276 mm Service Parts HST-42DDo not Discard this Manual