Vermont Casting VCS5017 To Start the Rotisserie Burner, Match Lighting the Rotisserie Burner

Page 14

Operation

LIGHTING THE ROTISSERIE BURNER (if equipped)

The Rotisserie burner provides the steady, even heat required to cook poultry and roasts to self-basted perfection.

TO START THE ROTISSERIE BURNER:

1. Always open the Hood completely before attempting to light the Grill.

WARNING: Never stand with your head directly over the Grill when preparing to light the Rotisserie burner, to prevent possible bodily injury.

2.Always confirm that all of the burner control knobs are in the OFF position before opening the gas supply.

3.Turn on the propane gas supply valve at the tank (1 to 2 turns) or turn on the main natural gas supply valve.

4.Turn the Rotisserie Burner Control Knob to the HIGH position, by pushing down on the knob and turning it counterclockwise.

5.Immediately push the Igniter Button. The Rotisserie burner should light within five seconds.

WARNING: IF THE ROTISSERIE BURNER DOES NOT LIGHT, immediately turn the burner control knob to the OFF position, to prevent gas buildup Wait five (5) minutes for the gas to clear and then repeat the preceding starting procedure. If the burner will not light when using the Igniter, follow the match lighting instructions below.

6.Confirm that the burner is properly lit and that the flame pattern is as desired, (see Figs. 9a, 9b & 9c, for the proper flame patterns). If the flame pattern is other than normal, consult the Troubleshooting Guide on Page 22 for corrective action.

7.Always preheat the Grill before starting to cook on the rotisserie.

8.Never operate the main burner when the rotisserie burner is on.

MATCH LIGHTING THE ROTISSERIE BURNER:

1. Always open the Hood completely, before attempting to light the Grill.

WARNING: Never stand with your head directly over the Grill when preparing to light the Rotisserie Burner, to prevent possible bodily injury.

2. Always confirm that all of the burner control knobs are in the OFF position before opening the gas supply.

3. Turn on the propane gas supply valve at the tank (1 to 2 turns) or turn on the main natural gas supply valve.

4. Insert a lit match or a butane lighter into the match lighting hole located below the rotisserie screen (see Fig. 11).

5. Turn the Rotisserie Control Knob to the HIGH position by pushing down on the knob and turning it counterclockwise.

Page 9

Rotisserie Lighting Hole

Fig. 11

Image 14
Contents USER’S Manual for Models Page Signal Words Safe Locations for USE of this Outdoor Grill Safe USE of LP Propane GAS Safe USE of Natural GASElectrical Safety Prevention of BurnsFuels Additional Warnings Safety For Your Safety LP Propane GAS Supply Connection Gas HookupNatural GAS Supply Connection To Connect To DisconnectControl Functions Propane Tank Valve Activating the Igniter Electronic Ignition SystemLighting the Main Burners Match Lighting the Main Burners Turning the Burners OFFFLARE-UPS To Start the Rotisserie Burner Match Lighting the Rotisserie BurnerRotisserie Setup if equipped Lighting the Side Burner if equipped Shutting the Burner OFFTroubleshooting Guide Troubleshooting Guide Assembly Procedures Unpack Carton and Verify ContentsInstall the Casters Install U-Clip Fasteners Parts RequiredInstall the Side Shelf Supports Parts Required Attach Shelves Parts RequiredSecure Condiment Tray to Console Parts Required Secure Shelves Parts RequiredSecure Side Shelf to Grill Parts Required Remove the Packing Tape Attach Side Burner Lid S/B-Single Parts RequiredAttach Knobs Parts Required Attach Stabilizer Bracket Parts Required Install the Grease Cup and Grease Pan Parts RequiredAttach the Handle to the Door Parts Required Install the Internal Components Parts Required Install the BatteryInstall the LP Cylinder LP Models Only Parts Required