Meco 2200 manual Care and Maintenance, Burner Maintenance, How to Clean the Burners

Page 11

CARE AND MAINTENANCE

Burner Maintenance

·Check the LP gas grill for gas leaks and Burner obstructions before each use.

·Always turn off the Control Knobs when not in use. Allow grill to cool before handling parts or cleaning.

Burners should be removed and cleaned annually, or whenever heavy build-up is found, to ensure that there are no signs of blockage (debris, insects) in either the burner portholes, the primary air inlet, or the neck of the burners. (See Burner cleaning instructions next page.)

CAUTION: SOME OF THE METAL EDGES MAY BE SHARP. BE CAREFUL IN HANDLING.

How to Clean the Burners

1)Make sure the Grill Control Knobs are turned to the “OFF” position, and the grill has completely cooled.

2)Disconnect the LP cylinder.

3)Remove Grease Cup, Cooking Surfaces and Leg Shelf.

4)Pull the Control Knobs off the valve stems. Remove: 5- screws, Grid Insert Guide, Control Panel and the Chain/Match Holder. (FIG. 23A)

5)Remove 2-Control Valve Spring Clips with screwdriver.

(FIG. 23B)

6)Remove Ignitor Wire Spring Clip by holding end of clip with pliers and pushing down away from the notch in burner bracket. (FIG. 23C) Hold spring with fingers so clip does not flip away.

7)Lay grill on the back side. Remove 5-screws holding the Burner Brackets to underside of Bowl. (FIG. 23D)

8)Remove both Burner Assemblies from the grill.

9)Use a pipe cleaner to clear obstructions from the Burner holes and inlet hole. (FIG. 23E & FIG. 23F) Verify that there are no insects or insect nests blocking the inlet hole. Normal wear and corrosion may enlarge some holes, however, if large cracks or holes are found the Burners should be replaced.

10)After cleaning, re-assemble Burner Assemblies and other parts in reverse order of previous Steps 2-9 disassembly. Note: When refitting the Burners, be sure the tubes are positioned correctly with the valves.

11)Check burner operation after reassembly or cleaning.

5-Screws Securing Control Panel

Grid Insert

Guide

5)Control Valve Spring Clip

FIG. 23B

6) Electrode Spring Clip

FIG. 23C

FIG. 23D

7)Remove 5-Screws from Burner Brackets under Grill bottom.

Oval Burner

FIG. 23E

9)Use a pipe cleaner to clear obstructions from all burner holes and the Inlet hole. A brass wire brush can be used on the burner surfaces to remove corrosion.

FIG. 23A

Round Burner

 

 

 

 

 

Chain/Match

 

 

 

 

 

Control Panel

 

 

Holder

 

 

 

 

 

FIG. 23F

 

 

 

 

 

 

 

 

 

 

 

 

 

11

Image 11
Contents Meco Corporation For Your SafetyImportant Safeguards Page Preparation and Grill SET-UP Page Attaching the LP GAS Cylinder to the Regulator Before Using Your LP GAS GrillLeak Testing How to perform a leak test See leak test diagrams nextLP Cylinder Operating Your LP GAS GrillGAS CYLINDER, Regulator Information Regulator Assembly Connecting/ Disconnecting LP Gas Cylinder to GrillPage Yellow Tip Grill CookingEnd of Cooking Session Turning Off Your LP Gas GrillHow to Clean the Burners Care and MaintenanceBurner Maintenance Grease Cup Cleaning the GrillPrecautions Preventive MaintenanceGrill Moving and Storage TroubleshootingBurner will not light using the ignitor Low flame or low heat Replacement PartsFlames blow out Flare upParts List Description QTY REL /2004