Fire Magic 000 BTU Installing Your Fire Magic Regal II Gourmet Series Barbecue, Exhaust Removal

Page 4

EXHAUST REMOVAL

If installed under a patio roof, the grill area should be fully covered by a non-combustible chimney and exhaust hood. An exhaust fan with a rating of up to 1000 CFM may be necessary to efficiently remove smoke and other cooking by-products from the covered area. Installation in fully-enclosed patio areas is not recommended.

GAS SUPPLY PLUMBING REQUIREMENTS

Rigid 1/2" or 3/4" black steel pipe, or local code approved pipe for temperatures up to 800°F (427°C), is required to conduct the gas supply into the enclosure opening for connection to the unit.

23 3/4"

28 1/4"

6"

12"

4"2"

2"

32 1/4"

Apply only joint compounds that are resistant to all gasses on all male pipe fittings. Make sure to tighten every joint securely. Do not use pipe joint compound to connect flare fittings.

The gas supply pipe should enter from the rear wall of the enclosure behind the Barbecue unit, at least 2" from either side, and between 2" and 8" above the floor as illustrated by the shaded area in Figure 2.

If it is not possible to stub the gas line in from the back of the enclosure, the connection may be made through the floor at the rear of the enclosure. Install the gas line stub at least 2" away from the side and back walls, but within 6" of the back wall as illustrated by the shaded area in Figure 2.

SAFETY NOTE: An external valve (with a removable key) in the gas line is necessary for safety when your Barbecue is not in use. It also provides for convenient maintenance and repair.

GAS SUPPLY AND MANIFOLD PRESSURES:

For Natural Gas - Normal 7" Water Column, Minimum 3 1/2", Maximum 10-1/2". For Propane gas - Normal 11" Water Column, Minimum 8", Maximum 13".

Figure 2 - Gas Stub Diagram

INSTALLING YOUR FIRE MAGIC REGAL II GOURMET SERIES BARBECUE

Perform the following checks before installing your Barbecue:

1. CHECK FUEL ORIFICES FOR PROPER SIZE

Your Regal II Barbecue is equipped with fuel orifices for Natural gas, unless otherwise indicated. To use with Propane gas, you must install smaller orifices to avoid hazardous overheating. The proper orifice size for Natural Gas is #52 (drill size). The proper orifice size for Propane gas is #57 (drill size).

2.IF YOU ARE NOT SURE YOU HAVE THE CORRECT BARBECUE BURNER ORIFICE SIZE:

a. Remove the Cooking Grids and Flavor Grids from your Barbecue.

b.If the gas supply has been connected, make sure the Burner Valves are in the “Off” position. Then pull the Valve knobs from their stems. Use a Phillips screwdriver to turn the Face Fastener Screws counter clockwise to release the Face and remove it from the Barbecue. Make sure to retain the screws and finish washers until you are ready to reattach the Face.

NOTE: Carefully lift the face away from the frame. The Spark Generator for the ignition system is attached to the inside of the face panel. The Ignitor Knob need not be detached, but the wires must be unplugged from the generator before the face is removed.

c. Lift off and remove one of the three galvanized steel Heatshields which are resting over the necks of each pair of Burners.

d. Check the orifice size by lifting a Burner up off of the stainless steel screw, or peg, at the back side of the unit and pulling it away from the orifice. The drill size is stamped on the face of each orifice. Be sure not to lose the Air Shutter or Air Shutter Spring which may become detached when the Burner is removed.

e. Change all six orifices if necessary, following instructions provided with your replacement orifices (furnished with all Fire Magic Gas Barbecues).

f.After checking orifice drill size, install the Air Shutter Spring and the Air Shutter over the orifice holder fit- ting, between the Burner and the Pipe Manifold, in the order and position shown in Figure 3.

g.Carefully place the Burners back on the screws or pegs so that the brass orifice and orifice holder fittings project deeply into the Burners.

h.Replace the galvanized Heatshields.

ORIFICE HOLDER/BURNER MANIFOLD

BURNER

BURNER NECK

SPRING

Figure 3 - Burner Orifice Diagram

AIR SHUTTER

ORIFICE

4

Image 4
Contents Installation and Operating Instructions Regal II Gourmet Series Outdoor GAS Barbecue 82,000 BTUFire Magic Regal II Gourmet Series GAS Barbecue Parts List Instructions forWhere to Install Your GAS Barbecue Insuring Proper Combustion AIR and Cooling AIR FlowVentilation of Enclosures Electrical OutletsInstalling Your Fire Magic Regal II Gourmet Series Barbecue Exhaust RemovalGAS Supply Plumbing Requirements GAS Supply and Manifold PressuresAdjusting Your Barbecue Install the Flavor GridsAIR Shutter Adjustment Adjusting the Flame HeightSafety Information Barbecue Safety and MaintenanceUSE and Care of Your Barbecue Drip Collection SystemBurner Maintenance Stainless Steel Cooking GridsPorcelain Coated Cast Iron Grids Protecting Parts and FinishLighting Instructions For Automatic LightingFor Manual Lighting If YOU Smell GAS

000 BTU, REGAL II 82 specifications

The Fire Magic REGAL II 82,000 BTU is a high-performance gas grill designed for outdoor cooking enthusiasts who seek both power and elegance. This grilling machine seamlessly combines advanced technology, robust construction, and an array of features that elevate the outdoor cooking experience.

With an impressive 82,000 BTU output, the REGAL II delivers outstanding heat performance, enabling chefs to sear meats, grill vegetables, and prepare a variety of dishes with precision. The grill features a spacious cooking surface, accommodating multiple food items simultaneously, making it ideal for family gatherings or entertaining guests. This model also includes a stainless steel cooking grate that ensures excellent heat retention and distribution.

One of the standout features of the Fire Magic REGAL II is its advanced ignition system. The reliable push-button electronic ignition allows for quick and easy lighting, ensuring that users spend less time preparing and more time enjoying the grilling experience. Additionally, the grill is equipped with advanced burners made from high-quality stainless steel, which are designed to resist corrosion and provide even heat across the cooking surface.

The REGAL II also boasts a unique heat zone separator that allows users to maintain different cooking temperatures across the grill. This innovative feature permits a versatile cooking experience, letting you simultaneously grill different foods that require varying degrees of heat. In addition to this, the grill comes equipped with a built-in infrared rotisserie burner, perfect for slow-roasting meats to perfection.

Durability and aesthetics have been prioritized in the design of the Fire Magic REGAL II. The grill's construction features heavy-duty stainless steel, providing resilience against the elements while also imparting a sleek, modern look that complements any outdoor kitchen setup. The hood is designed with a double-walled construction to improve heat retention, and the commercial-grade cast aluminum body ensures long-lasting performance.

For added convenience, the REGAL II is equipped with built-in lights that illuminate the cooking surface at night, making it easy to keep an eye on your food regardless of the lighting conditions. The grill’s side shelves provide ample workspace for food prep, while storage options keep cooking tools and accessories organized and within reach.

In conclusion, the Fire Magic REGAL II 82,000 BTU gas grill stands out in the outdoor cooking market for its impressive performance, innovative features, and sturdy construction. Whether you are an amateur griller or a seasoned barbecue expert, this grill promises to enhance your outdoor cooking adventures with its blend of functionality and style.