Adjusting Your Barbecue

3. CONNECT THE GAS SUPPLY TO BARBECUE

a.You will need an CSA approved stainless steel flex connector to bring the gas supply from the gas line stub to the Valve Manifold. A 1/2" x 36" or 48" flex connector with 1/2" flare to 1/2" pipe adapter on one end, and a 1/2" flare female fitting on the other end is suitable for most installations. CAUTION: Use only stainless steel flex connectors that are C.S.A. listed.

WARNING: A rubber or plastic connector will rupture or leak, resulting in an explosion or serious injury if used inside the Barbecue enclosure.

b.Make sure that your gas supply is turned off! Then connect the 1/2" pipe adapter fitting supplied with the stainless steel flex connector to the gas supply stub. Use pipe joint compound that is resistant to all gasses on the male pipe fitting and tighten securely. Do not use pipe joint compound to connect the Flare Fittings.

c.Slide your Barbecue into place, making sure not to pinch or kink the gas connector.

d.Bring the flex connector around the left-hand side of the Barbecue. Use the Locator Angle Brackets on the left lower-frame to position the flex connector. Continue the flex connector along the left side to the front of the unit and the Valve Manifold Inlet. Be careful not to block the 1" Front Vent opening as this will obstruct Drip Tray removal.

e.Connect the flex connector to the Flare Fitting on the Manifold Inlet. Support the Manifold Inlet Fitting with a wrench to avoid applying excessive torque to the Manifold Assembly while tightening this connection securely. Do not use pipe compound on Flare Fittings.

NOTCH

FLAVOR GRID

BURNER CAPS

BURNER

Figure 4 - Flavor Grid Diagram

f.Make sure the Barbecue Burner valves are in the "OFF" position. Turn the gas supply on. Then carefully check all gas connections for leaks with a brush and soapy water before lighting. NEVER USE A MATCH OR OPEN FLAME TO TEST FOR LEAKS.

g.Refer to the "Air Shutter Adjustment" Instructions below before replacing Barbecue face and knobs.

4. INSTALL THE FLAVOR GRIDS

a.Place the Flavor Grid Burner caps directly on the Burners. Make sure the notched end of the Burner Cap rests over the Ignitor Box (Figure 4). Center the Grids over the Burners with the open side up. This allows heat from the Burners to be evenly distributed throughout the cooking area. Flavor Grids heat and cool quickly, making your Fire Magic Barbecue very responsive to the changes you specify in grill temperature.

The Flavor Grids are made of stainless steel. They are rust resistant and may be cleaned with standard oven cleaners.

IMPORTANT: This appliance will not light and will not heat evenly or cook properly unless the Air Shutters are adjusted following installation (Reference "Air Shutter Adjustment", below).

Burner Air Shutters are easily accessed by removing the Front Panel (Face). The Air Shutters are located at the front of the Burners behind the Face (see Parts List). The Air Shutter has a small dimple (see Figure 5A), which allows it to lock into notches in the burner face. This prevents the air shutter from moving. Close the air shutters by turning the tabs to a vertical position. (Figure 5B). Light your Barbecue in accordance with lighting instructions (Page 8) and burn for 2 minutes with the valves on high and the oven open.

PARTIALLY OPEN

FIGURE 5ATAB

DIMPLE

NOTCH	FLAME OFF PORTS

CLOSED	(TURN TABS)
FIGURE 5B

FLAME ON PORTS

Figure 5A & 5B - Air Shutter Adjustment Diagram

AIR SHUTTER ADJUSTMENT

After burning for 2 minutes, open the Air Shutters until the flames lift off, or appear not to be touching the Burners. Then begin closing the Air Shutters until the flames appear to burn while touching the Burner Ports (Figure 5B). You may then see short yellow tips on the flames. If flames are a lazy yellow, open the Air Shutters until the flame is blue with yellow tipping.

NOTE: Barbecues in some installations achieve a better air/gas mixture and will ignite more quickly if the valve is first turned beyond High to Medium or Low for lighting.

ADJUSTING THE FLAME HEIGHT

The large knobs on the Face of the Barbecue control the Valves and adjust flame height. The first position is “High,” the second “Medium” and the final “Low.” Flame height can also be set anywhere between the High, Medium, and Low settings for all cooking requirements and tastes.

Height of the flame with the valve in low position may be regulated by means of a small adjusting screw in the center of the valve stem. This screw is accessible by removing the plastic valve knob which pulls straight off the end of the valve stem.

000 BTU, REGAL II 82 specifications

The Fire Magic REGAL II 82,000 BTU is a high-performance gas grill designed for outdoor cooking enthusiasts who seek both power and elegance. This grilling machine seamlessly combines advanced technology, robust construction, and an array of features that elevate the outdoor cooking experience.

With an impressive 82,000 BTU output, the REGAL II delivers outstanding heat performance, enabling chefs to sear meats, grill vegetables, and prepare a variety of dishes with precision. The grill features a spacious cooking surface, accommodating multiple food items simultaneously, making it ideal for family gatherings or entertaining guests. This model also includes a stainless steel cooking grate that ensures excellent heat retention and distribution.

One of the standout features of the Fire Magic REGAL II is its advanced ignition system. The reliable push-button electronic ignition allows for quick and easy lighting, ensuring that users spend less time preparing and more time enjoying the grilling experience. Additionally, the grill is equipped with advanced burners made from high-quality stainless steel, which are designed to resist corrosion and provide even heat across the cooking surface.

The REGAL II also boasts a unique heat zone separator that allows users to maintain different cooking temperatures across the grill. This innovative feature permits a versatile cooking experience, letting you simultaneously grill different foods that require varying degrees of heat. In addition to this, the grill comes equipped with a built-in infrared rotisserie burner, perfect for slow-roasting meats to perfection.

Durability and aesthetics have been prioritized in the design of the Fire Magic REGAL II. The grill's construction features heavy-duty stainless steel, providing resilience against the elements while also imparting a sleek, modern look that complements any outdoor kitchen setup. The hood is designed with a double-walled construction to improve heat retention, and the commercial-grade cast aluminum body ensures long-lasting performance.

For added convenience, the REGAL II is equipped with built-in lights that illuminate the cooking surface at night, making it easy to keep an eye on your food regardless of the lighting conditions. The grill’s side shelves provide ample workspace for food prep, while storage options keep cooking tools and accessories organized and within reach.

In conclusion, the Fire Magic REGAL II 82,000 BTU gas grill stands out in the outdoor cooking market for its impressive performance, innovative features, and sturdy construction. Whether you are an amateur griller or a seasoned barbecue expert, this grill promises to enhance your outdoor cooking adventures with its blend of functionality and style.