Desa (V)KC36PE SERIES, (V)KC36NE SERIES Wall Switch Installation, Replace top and bottom louvers

Page 26

Fireplace

Installation

Continued

7.Remove three screws from deflector shield on the inside top of firebox. Set shield and screws aside.

8.Install rear brick panel first. Rest bottom edge of panel on back edge of burner assembly (see Figure 39).

9.Install left side brick panel by sliding it be- tween the burner assembly and the side of the firebox (see Figure 39).

10.Install the right brick panel using the same method described in step 6 for left brick panel.

11.Replace deflector shield using screws removed in step 7.

12.Using screws removed in step 6, replace plenum and attach to burner.

13.Carefully replace the ember pod and log set.

14.Use screws removed in step 4 to replace andiron assembly.

15.Install lava rock and glowing embers. See

Installing Lava Rock and Glowing Embers, page 25.

16.Close glass door and lock latches on top and bottom of door and replace screen. See Removing Glass Door, steps 5 and 6, page 25.

17.Replace top and bottom louvers.

Left Side Brick

Panel

Rear Brick

Panel

WALL SWITCH INSTALLATION

The installation of a wall switch allows you to ac- tivate the gas control valve and turn the fireplace on and off. The wall switch is to be connected to the incoming 120 volt regular household wiring that supplies the electricity to the fireplace.

optional Remote control INSTALLATION (model WRC)

Note: If using optional wireless hand-held remote control, the wall switch must be in the ON position to be operational. The remote control then becomes the switching mechanism for fireplace operation.

1.Open lower louver panel.

2.The WRC model receiver does not require a battery. The receiver can be installed by first plugging the short extension cord into the fireplace receptacle. Then plug the receiver unit into the extension cord. Finally plug the ignition module plug into the receiver unit (see Figure 40).

3.Activate the remote handset battery by removing the insulating tab on the back of the handset (see Figure 41). The battery is included pre-installed.

4.Once the battery is activated the unit is ready to use.

5.Close lower louver panel.

Remote

FireplaceControl

Receptacle Receiver

Extension Cord

Ignition

 

Module Plug

Figure 40 - Installing the WRC Remote

Receiver

Battery Cover

12 Volt Battery

Figure 39 - Installing Rear Brick Panel

Back of

Pull to Remove

 

 

Handset

 

Insulation Tab

 

 

Figure 41 - Installing Battery into Back of

Handset

26

www.desatech.com

116238-01E

Image 26
Contents What to do if YOU Smell GAS Patent PendingTable of Contents Safety InformationSafety information High traffic areas Product IdentificationLocal Codes Location and space requirements Product FeaturesPre-Installation Preparation Front Top of Standoffs Vent ClearancesFraming and finishing For specific ventingClearances for Combustible Mantels Location of Termination Cap Balcony with Perpendicular Side WallVenting Installation Instructions Installation PrecautionsInstallation Planning Installing Horizontal Vent Cap Noncombustible Exterior Square Termination Round TerminationCorner Installation Recommended Applications Corner ground floor installationHorizontal System Installation Using TWO 90 Elbows Connect a section of pipe and extend up through the hole Installation for vertical terminationFlat Ceiling Installation Twist-lock the vent cap onto the last section of vent pipe High Altitude Installation Vertical VentingParts list for venting kits and components Desa 5/8 Pipe & Vent Kits Number DescriptionModel BK Installation Fireplace InstallationInstalling optional blower accessories Plug in blower power cordModel BKT Installation Blower Model BKTInstallation Items Needed Installing Gas Piping to Fireplace LocationBlower Wiring Diagram Connecting Fireplace to GAS Supply Propane/LP Supply TankExternal Regulator Vent Pointing DownClose equipment shutoff valve see Figure Checking GAS ConnectionsTest Pressures Equal To or Less Than Psig 3.5 kPa Disconnect fireplace and its individual equipRemoving Glass Door Pressure Testing Fireplace Gas ConnectionsRemoving Louver Panels Replace screen/rod assembly by reversing step Installing lava rock and glowing embersInstalling Brick liner Models BL36DASA and BL36DHASA Cleaning Glass DoorReplace top and bottom louvers Wall Switch InstallationOptional Remote control Installation model WRC Wiring Diagram PilotLighting Instructions For your safety Read before lightingOperating Fireplace To Turn OFF GAS To ApplianceInspecting Burners Operating optional blower accessoryPilot Assembly Optional Remote OperationPilot and burners Cleaning MaintenanceGlass Door LogsVenting system TroubleshootingObserved Problem Possible Cause Remedy No gas to burner, although wall Wall switch wires defective Check wiring connectionUle And/or check ground wire to Low, causing safety pilot toStatement at top Gas leak. See WarningTechnical Service Replacement PartsService Hints SpecificationsAccessories Illustrated Parts Breakdown Models KC36NE, VKC36NE, KC36PE and VKC36PE seriesParts List 19 18 31 33 116238-01E Firebox Bottom Limited Warranty DIRECT-VENT Fireplace Warranty InformationKeep this Warranty