Desa CGCFTN Connecting Equipment Shutoff Valve to Heater Control, Installation Items Needed

Page 15

OWNER’S MANUAL

INSTALLATION

Continued

CONNECTING EQUIPMENT SHUTOFF VALVE TO HEATER CONTROL

Installation Items Needed

Phillips screwdriver

sealant (resistant to propane/LP gas, not provided)

1.

Remove fireplace screen. Remove two

 

screws that hold fireplace screen in

 

place for shipping. These screws are

 

located near top of screen. Discard

 

screws. Lift fireplace screen up and pull

 

out to remove.

2.

Remove screws that attach branch sup-

 

port to fireplace (see Figure 24). Care-

 

fully lift up branch support and remove

 

from fireplace (see Figure 24).

3.

Route flexible gas line, included, from

Screen

Shipping

Branch Screw

Support

Shoulder Screw

Flexible Gas

Line

Screen

Figure 24 - Removing Log Base Assembly From Fireplace

To Fireplace

Gas Regulator

fireplace control to equipment shutoff

valve through side or rear access holes

in outer casing.

NOTICE: Most building codes do not permit concealed gas con- nections. A flexible gas line is provided to allow accessibility from the fireplace (see Figure 24).

Flexible Gas Line from Fireplace Gas Regulator Provided With Fireplace

Equipment

Shutoff Valve

To Gas

 

 

Supply

The flexible gas supply line con- nection to the equipment shutoff valve should be accessible.

CAUTION: Avoid damage to regulator. Hold gas regulator with wrench when connecting it to gas piping and/or fittings.

4.Apply pipe joint sealant lightly to male threads of gas connector attached to flexible gas line/equipment shutoff valve (see Figure 25).

5.Check all gas connections for leaks. See Checking Gas Connections, page 16.

6.Replace branch support back into fire- place. Feed flexible gas line into fire- place base area while replacing branch support. Make sure the entire flexible gas line is in fireplace base area. Reat- tach branch support to fireplace with screws removed in step 2.

Figure 25 - Attaching Flexible Gas Line to Equipment

Shutoff Valve

Continued

107035

15

Image 15
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualCgcftn VENT-FREE Natural GAS Compact Fireplace Safety InformationProduct Identification Product FeaturesLocal Codes UnpackingAssembling Hood AssemblyInstalling Log Assembling FireplaceConfined and Unconfined Space AIR for Combustion and VentilationProviding Adequate Ventilation Unusually Tight ConstructionAIR for Combustion Ventilation Determining FRESH-AIR Flow for Fireplace LocationDetermining if You Have a Confined or Unconfined Space Ventilation AIR Ventilation Air From Inside BuildingVentilation Air From Outdoors Check GAS Type InstallationInstallation Items Locating FireplaceRough Opening for Installing in Wall BUILT-IN Fireplace InstallationOptional Mantel Installation Mantel Clearances for BUILT-IN InstallationRemoving Valve Cover Shield Installing Blower Accessory GA3450TRemoving Upper Louver Assembly Installing Blower AssemblyInstall the switch plate on the valve Wiring Diagram For Blower Accessory Built-In Installation For Built-In InstallationConnecting to GAS Supply Attaching Wood Base to Solid FloorExtension Cord Installation Items Needed Connecting Equipment Shutoff Valve to Heater ControlPressure Testing Gas Supply Piping System Pressure Testing Fireplace Gas ConnectionsChecking GAS Connections For Your Safety Read Before Lighting Operating FireplaceLighting Instructions Inspecting Burner Observed Problem Possible Cause Remedy TroubleshootingMaintenance, Gas leak. See Warning statement at Specifications Technical ServiceParts Centrals Cleaning and Maintenance Replacement PartsService Hints Cgcftn Illustrated Parts BreakdownKEY Description QTY Parts ListAccessories 107035 Warranty Information