Desa CF26NT installation manual For Built-In Installation, Installing Blower Bracket Assembly

Page 11

INSTALLATION

Installing Blower Assembly - GA3450T (Cont.)

11

INSTALLATION

Continued

4.Note the wire locations on back of AUTO/OFF/ON switch. Carefully remove red wire from the AUTO terminal and blue wire from the ON terminal. Black wire can remain on the middle or OFF terminal (see Figure 16).

5.Carefully disconnect green and white wires from power cord harness at their insulated connectors.

6.In top of the heater cabinet, locate the four mounting holes on the outer casing. Align these four holes with those on the blower bracket assembly. Attach blower bracket assembly to the outer casing with 4 - #10 screws provided (see Figure 16).

7.Route the wire harness through the hole to the left side of heat deflector. Pull wire harness through lower opening to the left of the blower control shield. (see Figure 16).

8.Insert the 4 wire harness into one of the round holes in the rear of the blower control shield and through the rectangular hole in the front of shield (see Figure 16).

9.Reconnect red wire to the AUTO switch position. Reconnect blue wire to the ON switch position. Reconnect green and white wires to the power cord.

Wiring Routing Hole

Blower Bracket

AssemblyHeat

Deflector

Screw

Switch

Wire Harness

 

Power

 

Cord

Blue

Red

 

Switch

Wire

Harness

Plate

 

Blower

 

Control

Shield Cover

Shield

Figure 16 - Installing Blower Bracket Assembly

10.Install the switch plate on the blower control shield with 2 - #10 screws provided (see Figure 17). Route power cord out of the cabinet by inserting it through the bushing on the outer casing (see Figure 16). Plug fan kit into 120-Volt grounded power sup- ply and test operation. Note: When switch is in the AUTO posi- tion, the fan will start after the heater has run for a few mo- ments. The fan will continue to run for several moments after the heater has been turned off. When switch is in the ON posi- tion, the fan will run until turned to OFF. Reinstall hood assem- bly and close lower louver door.

11.Place log set back on the unit.

Blower

Control

Shield

Switch Plate

Screw

Figure 17 - Installing Switch Plate to Blower Control Shield

For Built-In Installation

WARNING: A licensed electrician must connect the wiring harness to electrical supply following all local codes. Electrician must provide a clamp on the box cover to secure the wiring. Wiring should be routed through the bushing in the hole on the outer casing of heater.

1.Install a snap bushing found in hardware kit into one of the holes found on rear of blower control shield. The other hole is for a strain relief clamp (not supplied) to secure incoming elec- trical supply.

2.Follow steps 2 through 6 in Installing Blower Assembly begin- ning on page 10. Also remove black wire from middle/OFF switch terminal.

3.Remove black plastic strain relief and power cord from switch plate (see Figure 18, page 12). The power cord supplied will not be used in built-in installations. Pop in the plastic snap bushing found in hardware kit into the hole left by supply cord/ strain relief.

4.A licensed electrician must follow the wiring diagram in Figure 19, page 12 to connect incoming electrical supply to fan kit wiring harness.

For morevisit www..com

111410-01C

Page 10 Page 12
Image 11
Page 10 Page 12
Contents What to do if YOU Smell GAS OWNER’S Operation and Installation ManualSafety Information Table of ContentsVent-Free Bay Front Compact Fireplace Product IdentificationAIR for Combustion and Ventilation Product FeaturesLocal Codes UnpackingDetermining if You Have a Confined or Unconfined Space Determining FRESH-AIR Flow for Heater LocationConfined and Unconfined Space Ventilation Air From Inside Building InstallationVentilation AIR Check GAS TypeLocating Fireplace Rough Opening for Installing in Wall BUILT-IN Fireplace InstallationAssembling Trim Optional Mantel InstallationMantel Clearances for Built-In Installation Removing Brick Liner RetainerRemoving Screen Installing Blower Assembly GA3450TInstalling Blower Bracket Assembly For Built-In InstallationInstallation Items Connecting to GAS SupplyInstallation Items Needed Connecting Fireplace to GAS SupplyChecking GAS Connections Pressure Testing Gas Supply Piping SystemPressure Testing Fireplace Gas Connections Installing LogsTo Turn OFF GAS To Appliance For Your Safety Read Before LightingOperating Fireplace Lighting InstructionsInspecting Burners Cleaning MaintenanceCabinet SpecificationsService Hints Technical ServiceObserved Problem Possible Cause Remedy TroubleshootingRefer to Air for Combustion and Venti Top Models CF26PT Shown CF26NT Illustrated Parts BreakdownKEY Part Number CF26PT CF26NT Description QTY Parts ListModels CF26PT and CF26NT KEY Description QTY Parts Centrals Replacement PartsParts Under Warranty Parts not Under WarrantyOwners Registration Form Postage Required Corner Mantel with Full Hearth Base AccessoriesBrass Accent Trim GA6095 Cabinet Mantel with Full Hearth BaseKeep this Warranty Warranty Information

CF26NT specifications

Desa CF26NT is a modern gas fireplace that showcases a blend of contemporary design and efficient heating technology. Established to elevate the aesthetic appeal of homes while ensuring optimal warmth, the CF26NT stands out with its sleek lines and sophisticated finish. With a focus on user experience, this fireplace is not just a source of heat but a centerpiece that enhances any living space.

One of the main features of the Desa CF26NT is its innovative design, which allows it to fit seamlessly into various interior styles. The fireplace is built with a large viewing window, providing an expansive view of the flames. This not only adds to the ambiance but also creates a sense of openness in the room. The minimalist frame and clean edges contribute to a modern aesthetic, making it a perfect addition to contemporary living areas.

In terms of technology, the CF26NT utilizes advanced gas burning systems, which ensure efficient fuel use and lower emissions. This fireplace is designed to provide consistent heat output while minimizing the environmental impact. With adjustable flame heights, users can customize the intensity of the fire, allowing for a personalized heating experience that can cater to different occasions.

Moreover, the Desa CF26NT is equipped with a user-friendly control system that allows for effortless operation. The intuitive interface enables users to easily adjust the temperature and flame settings, ensuring comfort at their fingertips. For added convenience, many models come with remote control options, allowing users to operate the fireplace from the comfort of their seating area.

Another noteworthy characteristic of the CF26NT is its safety features. The fireplace includes an automatic shut-off system that activates in case of any malfunction or overheating, providing peace of mind for homeowners. Additionally, the unit is designed with insulated materials, ensuring that the exterior remains cool to the touch, making it safe for households with children and pets.

In conclusion, the Desa CF26NT is an exceptional choice for anyone looking to enhance their home with a stylish, efficient, and safe gas fireplace. Its combination of modern design, innovative technology, and user-centric features make it a standout option in the market for gas fireplaces today. Whether for heating or aesthetic purposes, the CF26NT promises to deliver an exceptional experience.
Top Page Image Contents