Desa and EFS26NR, EFS10TP, EFS10TN Assembling Brass Trim Brass trim shipped with mantel

Page 12

12

INSTALLATION

Optional Mantel Installation (Cont.)

Installing Blower Accessory GA3450T in Remote-Ready Models

INSTALLATION

Continued

10. Attach wood base to floor with two 1 3/4" black screws pro- vided (see Figure 13). If the floor is concrete use anchor method (see Attaching Wood Base to Solid Floor, page 17).

11. Install gas line. See Connecting To Gas Supply, pages 17 and 18.

12. Check for leaks. See Checking Gas Connections, page 19.

13. Place mantel around fireplace. Be careful not to damage wall or mantel.

14. Place brass trim kit on the shoulder screws located on the side and top of the fireplace. Firmly snap the brass trim over the shoulder screws on fireplace (see Figure 12, page 11).

15. Adjust assembly to remove any gaps. Attach remaining two 3" wood screws from hardware pack through openings inside of fireplace sides into the mantel. The openings are located at top behind the area for the brass louvers (see Figure 12, page 11).

16. Reinstall top brass louvers.

1 3/4" Screw

Wood Base

Figure 13 - Attaching Wood Base to Floor

Assembling Brass Trim (Brass trim shipped with mantel)

1.Remove packaging from three remaining pieces of brass trim.

2.Locate two adjusting plates with set screws, and two shims in the hardware packet.

3.Align shim under adjusting plate as shown in Figure 14.

4.Slide one end of adjusting plate/shim in slot on mitered edge of top brass trim (see Figure 14).

5.Slide other end of adjusting plate/shim in slot on mitered edge of side brass trim (see Figure 14).

6.While firmly holding edges of brass trim together, tighten both set screws on the adjusting plate with slotted screwdriver.

7.Repeat steps 1 through 6 for other corner.

8.Set brass assembly aside for later installation.

Set

Screws

Adjusting

Top Brass Trim

Plate

Slot

 

Mitered Edge

Shim

 

Side Brass Trim

Figure 14 - Assembling Brass Trim

INSTALLING OPTIONAL BLOWER ACCESSORY GA3450T IN REMOTE-READY MODELS

Removing Upper Louver Assembly and Branch Support

To install the blower accessory, you must first remove the upper louver assembly.

1.Lift screen off fireplace and remove log set if installed.

2.Remove 2 screws from each side of branch support and pull branch support out (see Figure 15).

3.Remove 4 brass-plated screws from upper louver assembly (see Figure 15). Save these screws.

4.Pull upper louver assembly straight out from the cabinet. Be care- ful not to scratch the paint. Set louver assembly and screws aside.

5.Open lower louver door by swinging door down (see Figure 16, page 13).

Blower Bracket

Mounting Holes

Upper Louver

Assembly

Branch Support

Figure 15 - Removing Upper Louver Assembly and Branch Support

For..com

107032-01H

Page 11 Page 13
Image 12
Page 11 Page 13
Contents OWNER’S Operation and Installation Manual Unvented VENT-FREE GAS Compact Classic Hearth FireplaceWhat to do if YOU Smell GAS Table of Contents Safety InformationProduct Identification Vent-Free Compact Classic Hearth FireplaceOptional Remote Control Accessories Product FeaturesLocal Codes UnpackingAssembly Assembling FireplaceAIR for Combustion and Ventilation Providing Adequate VentilationDetermining FRESH-AIR Flow for Fireplace Location Ventilation AIR Ventilation Air From Inside BuildingInstallation Ventilation Air From OutdoorsInstallation Items Check GAS TypeFireplace Clearances BUILT-IN Fireplace Installation Rough Opening for Installing in WallOptional Mantel Installation Mantel Clearances for Built-In InstallationRemoving Upper Louver Assembly and Branch Support Assembling Brass Trim Brass trim shipped with mantelInstalling Blower Accessory Power Cord SnapFor Built-In Installation Removing Upper Louver AssemblyExtension Cord Installing Blower Assembly Removing Valve Cover ShieldValve Cover Shield Switch PlateScrew Connecting to GAS Supply Attaching Wood Base to Solid FloorConnecting Fireplace to GAS Supply Installation Items NeededPressure Testing gas Supply Piping system Checking GAS ConnectionsOptional Wireless HAND-HELD Remote Control Accessories Pressure Testing Fireplace Gas ConnectionsInstalling Receiver Installing 9-Volt Battery in Hand-Held Remote Control Unit Optional Wall Mounted Thermostat GWMT1Optional Wall Switch GWMS2 Remote-Ready Models Only Installing LOG SET and ScreenOperating Fireplace Lighting InstructionsManual Lighting Procedure REMOTE-READY Models For Your Safety Read Before LightingTo Turn OFF GAS To Appliance Thermostat Control OperationPropane/LPGasPilot Manual Mode Auto Thermostatic ModeOptional HAND-HELD Remote Operation Thermostat Series Model GhrctbGWMS2 Wall Mounted Switch Optional Operating Blower Safety FeaturesGWMT1 Wall Mounted Thermostat Optional Inspecting Burners Pilot Flame PatternBurner Flame Pattern Cleaning Maintenance Wiring DiagramCleaning Burner Injector Holder and Pilot AIR Inlet Hole LOG SETTroubleshooting Observed Problem Possible Cause RemedyRefer to Air for Combustion and Venti Gas leak. See Warning statement Specifications Replacement PartsService Hints Technical ServiceIllustrated Parts Breakdown THERMOSTAT-CONTROLLED Models VMH10TPB, VMH10TNBParts List THERMOSTAT-CONTROLLED Models22 36 REMOTE-READY Models Accessories Cleaning KIT GCK WALL-MOUNT Thermostat Switch GWMT1WALL-MOUNT ON/OFF Switch GWMS2 Receiver and HAND-HELD Thermostat Remote Control KIT GhrctbFor . .com Owners Registration Form Postage Required 107032-01H Warranty Information

EFS10TP, EFS10TN, and EFS26NR specifications

Desa is a recognized leader in the innovation and manufacture of advanced heating solutions designed to deliver optimal performance and efficiency. Among their most notable offerings are the EFS26NR, EFS10TP, and EFS10TN models, each engineered with unique features and technologies to meet diverse heating needs.

The EFS26NR is a notable model known for its large heating capacity and effectiveness in maintaining consistent warmth in larger spaces. With a robust output, this unit can efficiently heat areas up to 1,800 square feet, making it suitable for homes or commercial settings. One of the primary characteristics of the EFS26NR is its advanced heating technology, which includes a high-efficiency burner that maximizes fuel usage, reducing operational costs. Additionally, it features a built-in thermostat, providing automated temperature adjustments for enhanced comfort.

On the other hand, the EFS10TP is designed for versatility and practicality. This model is ideal for smaller rooms or as a supplementary heating option. The EFS10TP offers users the convenience of a portable heater equipped with wheels, allowing for easy mobility. This model is equipped with user-friendly controls and a safety shut-off feature, ensuring peace of mind while in use. The EFS10TP utilizes a compact design without sacrificing performance, allowing it to fit seamlessly into various settings.

Similar in size, the EFS10TN focuses on energy efficiency as its main selling point. This model uses a unique infrared heating technology that allows for more direct heating of objects and people rather than warming the air, resulting in lower energy consumption. The EFS10TN is perfect for those looking to reduce their carbon footprint while still achieving a warm, inviting environment. Enhanced safety features such as tip-over protection and overheat shut-off further ensure its suitability for use in homes with children or pets.

Overall, the Desa heating solutions—EFS26NR, EFS10TP, and EFS10TN—each provide distinct advantages tailored to specific heating requirements. With a commitment to innovation, safety, and efficiency, these models are exemplary choices for those seeking dependable and effective heating options. Whether for large areas or cozy spaces, Desa ensures that there is a suitable solution for every heating need.
Top Page Image Contents