Centro 6000 SI warranty F E T Y H O S E D R E G U L a T O R

Page 6

S A F E T Y H O S E

A N D R E G U L A T O R

Propane Gas Models: Your barbecue is designed to operate on L.P. (Propane) gas at a pressure of 2.74 Kpa (11˝ water column). A regulator preset to this pressure is supplied with the barbecue and must be used.

This regulator is equipped with the Type-1 quick-closing connecting system, which incor- porates these safety features:

•Will not allow gas to flow until a positive seal has been made.

•Has a thermal component that will automatically shut off the flow of gas between 115-150ºC (240-300ºF).

•Has a flow limiting feature, which will restrict the flow of gas to 10 cubic feet/hour.

Should the large, black thermal-sensitive coupling nut be exposed to any extreme tem- peratures above 115ºC it will soften and allow the regulator probe to disengage from the valve, and will shut off the gas. Should this occur, do not try to reconnect the nut; instead replace the whole regulator assembly with a new one (see the attached parts listing for details). The regulator probe also contains a flow-sensitive feature, which limits the flow of gas to 10 cubic feet/hour, in the event of a regulator malfunction or hose leak. If the flow control feature is activated, the cause of this excessive gas flow should be investigated and corrected before using the barbecue again.

Note: Improperly lighting the barbecue can activate the flow control feature, resulting in lower heat output. If this occurs, the re-flow feature must be reset by turning all the burner controls and the cylinder valve off. Wait at least 30 seconds before slowly turning on the cylinder valve, and then after another 5 seconds turn the burner valve on and light the barbecue.

•Never connect this barbecue to an unregulated propane gas supply, or to another kind of gas. Do not alter or change the hose or regulator in any way.

•Visually inspect the whole hose assembly before each use for evidence of wear or damage such as cracks, burns, or cuts. If any damage is found, replace the assembly before using the barbecue. Use only the recommended replacement hose.

•To avoid possible damage to the hose, do not allow any grease or other hot materials to fall on the hose, and make sure the hose does not contact any hot surfaces of the barbecue.

•The connection fitting must be protected when it’s disconnected from the cylinder. Do not allow the fitting to bump or drag on the ground as nicks and scratches could help create a leak when connecting back to the cylinder.

•It is important to do the “Leak Test” procedure every time a cylinder is refilled or any of the components are changed, and especially at the beginning of a new season.

Natural Gas Conversion Kit is available at Canadian Tire (Part# 85-1621-4)

4

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Serial # B L E O F C O N T E N T S E O F L P G a S C Y L I N D E R Installation I N F O R M a T I O ND I T I O N a L R N I N G S Self-contained Propane Gas SystemTo Avoid Unnecessary Risks N G E RCylinder must also be equipped with L L I N G T H E L P C Y L I N D E RI O R T O U S I N G Hose and Regulator InspectionF E T Y H O S E D R E G U L a T O R Perform a Leak Test To Reset The Gas Regulator Safety DeviceF E T Y A K T E S T I N G Following Must Be CheckedG H T I N G E G R I L L R N I N G If the Selected Burner does not LightTurning The Burners Off Match Lighting The Main BurnersLighting the Side Burner Lighting the Side Burner with a MatchVisually Check Burner Flame A R Z O N E O P E R a T I N G S T R U C T I O N S Guide to Rotisserie Cooking Match Lighting ProcedureP S O N U S I N G U R R O T I S S E R I E Balancing the FoodPage Item No Quantity Specification Ckcl Manual Tools Needed for Assembly S E M B L Y I N S T R U C T I O N SHardware Pack List Top Rear Granite Support Brace Hardware Tools Needed for Assembly Eleg Insert Page Page Page Page Turn EN Page Tank Holder Page Page S T R I B U T O R
Top Page Image Contents