Selecting a Location, Performing a Leak Test

SELECTING A LOCATION

To reduce the risk of serious bodily injury or death:

·This outdoor cooking appliance shall be used only outdoors and shall not be used in a building, garage, or any other enclosed area. Locate outdoor cooking appliance in an area with good ventilation on a level stable surface clear of combustible and flammable material.

·Maintain minimum clearances of 36” from back and sides of grill to any combustible construction.

·Do not locate this appliance under overhead unprotected combustible construction.

·This outdoor cooking appliance is not intended to be used in or on boats or installed in or on recreational vehicles.

·Do not use gas grill as a space heater.

PERFORMING A LEAK TEST

To reduce the risk of serious bodily injury or death:

·Perform a leak test before each use and each time a gas connection or disconnection is done .

·Perform a leak test in a well ventilated area.

·Never use an open flame to test for gas leaks.

·Never smoke near the grill during a leak test.

·Do not perform a leak test on a grill while it is hot or in use.

·Do not use the gas grill if you detect a gas leak that cannot be corrected by using the leak test procedures.

How to perform a leak test:

Supplies Needed for a Leak Test: Clean paint brush, water, and dish washing liquid.

1)Use an LP Cylinder equipped with an OPD (Overfill Prevention Device) and have it filled at an authorized LP gas dealer by a qualified attendant.

2)Make sure all of the grill control panel knobs are turned to the “off” position and verify that the LP gas cylinder valve is closed by turning the knob on the LP gas cylinder clockwise until it stops.

3)Mix one part of water with one part of dish washing liquid.

4)Remove Fabric Panel from the front legs if necessary.

5)Open the knob on the LP gas cylinder counter- clockwise. (FIG. 12A)

6)Check for leaks by brushing the soap solution on all gas valves, hose connections and fittings. (shown by the heavy arrows in (FIG. 12A & 12B) Make sure you generously brush the locations with the soap solution, completely surrounding the connections and fittings.

7)If “growing” bubbles appear on any of the connection points, you have detected a gas leak. Immediately close the LP cylinder valve by turning handle clockwise.

A)If leak appears at either end of hose and regulator assembly, retighten the connection at the leak, but do not over tighten. (Note: Only hand tighten at coupling nut) Repeat Leak Test.

B)If the leak is coming from the Gas Cylinder, from the valves at the control knobs, or if the leak cannot be stopped, do not use the grill. Call Customer Service at 1-800-251-7558.

8)Upon completion of leak test, turn all control knobs to the “off” position. Turn the handle on the LP gas cylinder clockwise until it stops. Disconnect LP gas cylinder by turning coupling nut on regulator in a counter clockwise direction until regulator is released from threaded LP cylinder gas nozzle.

9)Place the protective cap over LP cylinder gas nozzle.

After completing Leak Test, you are

ready to begin using your grill!

Turn LP Gas Cylinder valve counter-clockwise.

Regulator Seal

Regulator

Coupling Nut

FIG. 12A

Gas Valve Fittings

			Hose Fittings
	FIG. 12B		Hose Fittings
	FIG. 12B

7110.7.641 specifications

The Aussie 7110.7.641 is a versatile and robust machinery specifically designed to enhance productivity in various sectors, particularly in agriculture and construction. As part of its standout features, this model offers an impressive balance of power and efficiency, making it a preferred choice among professionals in these industries.

One of the key characteristics of the Aussie 7110.7.641 is its powerful engine, which delivers exceptional torque and horsepower. This allows the machine to handle heavy loads, navigate challenging terrains, and perform demanding tasks with ease. The well-engineered drivetrain ensures that power is effectively transmitted to the wheels, enhancing the overall maneuverability of the machine while minimizing fuel consumption.

The Aussie 7110.7.641 also incorporates state-of-the-art technologies that boost its performance and user-friendliness. It comes equipped with an advanced digital control system that enables operators to monitor machine performance in real time. This system provides critical information such as fuel efficiency, load weight, and operational status, allowing users to optimize their workflows and reduce downtime.

In addition to its advanced control system, the Aussie 7110.7.641 features ergonomic design elements that prioritize user comfort and safety. The operator's cabin is designed with adjustable seating, intuitive controls, and excellent visibility, making it easy for operators to maneuver the machine even in tight spaces. Safety features such as rollover protection systems and robust guarding ensure that users can operate the machine with confidence in various environments.

Furthermore, the Aussie 7110.7.641 supports a variety of attachments, enhancing its versatility. This adaptability allows it to perform multiple tasks, from tilling and plowing in agricultural settings to lifting and hauling materials in construction. With its sturdy construction and high-quality materials, this machine is built to endure the rigors of daily use.

Overall, the Aussie 7110.7.641 stands out in its category for its blend of power, efficiency, and advanced technology. Its ability to tackle diverse applications while prioritizing operator safety and comfort makes it an essential asset for businesses looking to improve productivity and streamline operations.