Brinkmann 4905 owner manual Cleaning and Maintenance, Burner ASSEMBLY/MAINTENANCE

Page 17

CLEANING AND MAINTENANCE:

Keep the appliance free and clear of combustible materials, gasoline and other flammable vapors and liquids.

Keep the ventilation openings of the cylinder enclosure free and clear of debris.

Visually check burner flames for proper operation (see pictorial in "Burner Assembly/Maintenance" under Proper Care and Maintenance). Spiders or other insects can nest in the burner causing gas blockage.

For safe grilling and peak performance of your grill, perform these checks at least twice per year or after extended periods of storage.

Be sure to tighten up all hardware (nuts, bolts, screws, etc.) at least twice per year.

CAUTION! Some parts may contain sharp edges. Wear protective gloves if necessary.

Remove the cooking grills, ceramic tiles, tile frames and burners from inside your grill. Use a brush with hot water and detergent to remove excess residue. NEVER use a commercial oven cleaner. Rinse completely with water. Towel dry and replace all components as described in the assembly instructions.

BURNER ASSEMBLY/MAINTENANCE

Although your burners are constructed of stainless steel, they may corrode as a result of the extreme heat and acids from cooking foods. Regularly inspect the burners for cracks, abnormal holes, and other signs of corrosion damage. If found, replace the burner.

DO NOT obstruct the flow of combustion and ventilation air. Burner tubes can become blocked by spiders and other insects building their nests. Blocked burner tubes can prevent gas flow to the burners and could result in a burner tube fire or fire beneath the grill. To clean the Burner Assembly follow these instructions to clean and/or replace parts of burner assembly or if you have trouble igniting the grill.

1.Turn gas off at control knobs and LP cylinder tank valve.

2.Remove cooking grills, ceramic tiles and tile frames.

3.Carefully lift each burner up and away from valve openings.

4.Use a narrow bottle brush or a stiff wire bent into a small hook to run through each burner tube and flame port several times.

NOTE: Wear eye protection when performing procedure 5.

5. Use compressed air to blow into burner tube and out

 

the flame ports. Check each port to make sure air

Debris

comes out each hole.

 

6.Wire brush entire outer surface of burner to remove food residue and dirt.

7.Check burner for damage, if any large cracks or holes are found replace burner. IMPORTANT: Burner opening must slide over valve nozzle.

8. Carefully replace burners.

9. Replace each burner and follow the "Gas Leak Testing" section of this manual. Relight burners to verify proper operation.

10. Replace tile frames,ceramic tiles and cooking grills.

Valve

Burner Orifice

Nozzles

PROPER BURNER OPERATION

16

Image 17
Contents Heavy-Duty Gas Grill For Your Safety Important SafetyTable of Contents General Warnings LP GAS Cylinder not Supplied with this Grill Installation InformationCylinder Specifications Regulator Resetting Procedure Installing the LP GAS Cylinder Onto the GrillFilling the LP GAS Cylinder Hose and RegulatorConnecting Hose and Regulator Connecting Hose and Regulator to AN LP GAS CylinderChecking for Leaks Leak TestingWhen to Perform a Leak Test PRE-START Check List Match Lighting the Main Burners Lighting InstructionsLighting the Main Burners Lighting the Side Burner Lighting the Rotisserie BurnerMatch Lighting the Rotisserie Burner Turning OFF the Grill Match Lighting the Side BurnerBreaking in Your Grill Operating the GrillPreheating the Grill Controlling FLARE-UPSSide Burner Rotisserie CookingHelpful Hints CleanlinessGrilling to Proper Temperature Burner ASSEMBLY/MAINTENANCE Cleaning and MaintenanceCeramic Tiles Cooking GrillsTransporting and Storage Before Storing Your GrillTrouble Shooting Frequently Asked Questions Frequently Asked Questions Assembly Instructions For Missing PARTS, Please Call Customer Service AT Step Step ProSeries 4905 Assembled Accessories Warranty
Related manuals
Manual 8 pages 44.79 Kb