Pride Mobility Jet 1 To charge the batteries using the onboard charger, OFF-BOARD Charger

Page 31

I X . B A T T E R I E S A N D C H A R G I N G

To charge the batteries using the onboard charger:

1.Position the rear of your Jet 1 close to a standard wall outlet.

2.Be certain the controller power is turned off and the freewheel levers are in the engaged position. See IV. “The Jet 1.”

3.Remove the battery charger cord from the back pouch of your Jet and plug it into the battery charger power outlet that is located on the utility tray. See figure 25.

4.Extend the charger power cord and plug it into the wall outlet. The Jet 1 incorporates an inhibit function that disables the power chair when the charger is plugged into a wall outlet.

5.The ammeter indicates how much charge is needed to fully recharge the batteries. Wait about a minute for the charger to warm up. The ammeter may move as high as 5.5 amps, then gradually move back down to 0 amps as the batteries charge.

6.We recommend you charge the batteries for 8 to 14 hours.As the batteries charge, the ammeter needle slowly drops to “zero” mark. When the batteries are fully charged, the needle vibrates on or about the “zero” mark on the ammeter scale.

7.When your Jet 1’s batteries are fully charged, you can unplug the power cord from the wall outlet, wind it up using the hook and loop strap, and place the cord back into the Jet 1’s back pouch.

OFF-BOARD CHARGER

If your Jet 1 is equipped with an off-board charger, follow these instructions.

1.Position your Jet 1 next to a standard wall outlet.

2.Be certain the controller power is turned off.

3.Remove the run plug located on the utility tray. This activates the inhibit function.

4.Plug the 3-pin extension cable to the charger, then into the utility tray connector.

5.Plug the charger cord into the wall outlet.

6.The ammeter indicates how much charge is needed to fully charge the batteries. Wait about a minute for the charger to warm up. The ammeter should move all the way up to 5 amps, then gradually move back down to 0 amps.

7.We recommend you charge the batteries for 8 to 14 hours. As the batteries charge, the ammeter needle will slowly drop to the “zero” mark. When the batteries are fully charged, the needle vibrates on or about the “zero” mark on the ammeter scale.

8.When your Jet 1’s batteries are fully charged, disconnect the charger cord from the wall outlet.

9.Disconnect the charger from the rear utility tray.

10.Reconnect the run plug into its connector.

NOTE: If the run plug is not reconnected, your Jet 1 will not run.

11. Replace the rear cover.

US Jet 1 ATS/Rev B/Jul03

www.pridemobility.com

31

Image 31
Contents Stylish Design and Premium Performance F E T Y G U I D E L I N E S N T E N T S Introduction N T R O D U C T I O NInformation Exchange My Authorized Pride Provider Is Pride Owners ClubS a F E T Y Pre-Ride Safety CheckModifications Tire Inflation Weight LimitationsIncline Information Cornering Information Braking InformationOutdoor Driving Surfaces Freewheel ModeStationary Obstacles Steps, Curbs, etc EMI & RFI Positioning Belts TransfersBatteries Inclement Weather Precautions Reaching and BendingRemovable Parts AlcoholWhere do radio waves come from? EMI-RFI-FREQUENTLY Asked Questions FaqsI . E M I / R F What is the FDA doing about the problem? Are all power chairs susceptible to EMI-RFI?What should I do if my power chair moves unexpectedly? Jet T H E J E TRear View Specifications Utility Tray Utility TrayFreewheel Levers To engage or disengage the freewheel featureACTIVE-TRAC System To mount the seatback to the hinge Parts List QuantitySeatback Assembly S S E M B L YTo install the seat Seat InstallationJoystick Installation To change the seat height To install the joystick controllerC O M F O R T a D J U S T M E N T S Seat HeightJoystick Extension Armrest WidthArmrest Angle Armrest Height OptionalElevating LEG Rests Option Footrest AngleBody Shroud Removal Battery RemovalI . D I S a S S E M B L Y Seat RemovalJoystick Battery Condition MeterI I . O P E R a T I O N Dynamic DL-50 ControllerSpeed Control Pin ConnectorPin Charger Inhibit Connector Joystick Out Of Neutral At Power UpFault Codes TroubleshootingBatteries B a T T E R I E S a N D C H a R G I N GCharging the Batteries OFF-BOARD Charger To charge the batteries using the onboard chargerInfrequent Use Battery BREAK-INTo break in new batteries for maximum efficiency Daily UseHow can I get maximum range or distance per charge? What type of battery should I use?Battery Specifications Why do my new batteries seem weak?What about shipping? How can I ensure maximum battery life?How should I store my Jet 1 and its batteries? What about public transportation?Should your Jet 1 come in contact with water Routine MaintenanceTemperature A R E a N D M a I N T E N a N C EWeekly Checks Daily ChecksTo check the brakes Storage Cleaning Instructions Tires and TubesMonthly Checks Yearly ChecksMotor Brushes Battery ReplacementFollow these easy steps for a quick and safe repair To replace the batteriesWhen to see Your Pride Provider for Service Corrective MaintenanceTo inspect or replace the motor brushes O P T I O N a L a C C E S S O R I E S Warranty Exclusions FIVE-YEAR Limited Frame WarrantyONE-YEAR Limited Warranty Warranty ExceptionsThere is no other express warranty Quality Control Model Jet 1 ATS